SIST EN 13981-3:2006
(Main)Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 3: Castings
Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 3: Castings
This document specifies requirements for castings which contribute to the structural properties of the railcar bodyshell and other major structural components.
It specifies particular requirements regarding qualification, quality control, material properties and dimensional tolerances and gives guide-lines for application and use.
Aluminium und Aluminiumlegierungen - Erzeugnisse für tragende Anwendungen im Schienenfahrzeugbau - Technische Lieferbedingungen - Teil 3: Gussstücke
Dieses Dokument Norm legt Anforderungen an Gussstücke fest, die für die tragenden Eigenschaften von
Wagenkästen für Schienenfahrzeuge und für andere wichtige tragende Bauteile maßgeblich sind.
Es legt besondere Anforderungen an Eignung, Qualitätsprüfung, Werkstoffeigenschaften und Maßtoleranzen
fest und gibt Leitlinien für Anwendung und Gebrauch an.
Aluminium et alliages d'aluminium - Produits pour applications ferroviaires structurales - Conditions techniques de contrôle et de livraison - Partie 3 : Pieces moulées
La présente Norme européenne spécifie les exigences pour les pieces moulées qui contribuent aux propriétés
structurales des caisses de véhicules ferroviaires et d'autres composants structuraux.
Des exigences particulieres concernant la qualification, le contrôle qualité, les propriétés des matériaux et les
tolérances dimensionnelles sont spécifiées. En outre, des lignes directrices pour l'application et l'utilisation
sont données.
Aluminij in aluminijeve zlitine – Proizvodi za železniške naprave - Tehnični pogoji za prevzem in dobavo – 3. del: Ulitki
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 3: CastingsAluminium et alliages d'aluminium - Produits pour applications ferroviaires structurales - Conditions techniques de contrôle et de livraison - Partie 3 : Pieces mouléesAluminium und Aluminiumlegierungen - Erzeugnisse für tragende Anwendungen im Schienenfahrzeugbau - Technische Lieferbedingungen - Teil 3: GussstückeTa slovenski standard je istoveten z:EN 13981-3:2006SIST EN 13981-3:2006en77.150.1045.040ICS:SLOVENSKI
STANDARDSIST EN 13981-3:200601-november-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13981-3September 2006ICS 77.150.10 English VersionAluminium and aluminium alloys - Products for structural railwayapplications - Technical conditions for inspection and delivery -Part 3: CastingsAluminium et alliages d'aluminium - Produits pourapplications ferroviaires structurales - Conditionstechniques de contrôle et de livraison - Partie 3 : PiècesmouléesAluminium und Aluminiumlegierungen - Erzeugnisse fürtragende Anwendungen im Schienenfahrzeugbau -Technische Lieferbedingungen - Teil 3: GussstückeThis European Standard was approved by CEN on 6 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13981-3:2006: E
EN 13981-3:2006 (E) 2 Contents Page Foreword.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Ordering information.6 5 Requirements.7 5.1 Production and manufacturing processes.7 5.2 Quality assurance.7 5.3 Chemical composition and tempers.7 5.4 Mechanical properties of castings.8 5.4.1 Mechanical properties of castings under static loading.8 5.4.2 Mechanical properties of castings under cyclic loading.8 5.5 Properties of welded joints.8 5.6 Internal defects.8 5.7 Surface imperfections.8 5.8 Finishing welding.8 5.9 Tolerances on dimensions and form.9 6 Qualification procedures.9 6.1 First-off article approval procedure.9 6.2 Additional qualification procedure.9 7 Sampling and test methods.10 7.1 General.10 7.2 Analysis of chemical composition.10 7.3 Tensile test.10 7.4 Preparation of test pieces for the testing of welded joints.11 7.5 Tensile testing on welded joints.11 7.6 Fatigue testing.11 7.7 Visual inspection.11 7.8 Dye penetrant testing.11 7.9 X-ray examination.11 7.10 Measurement of dimensions.11 8 Traceability.11 9 Marking of products.12 10 Inspection certificate.12 11 Record keeping.12 12 Packaging.13 13 Application and use.13 14 Complaints of non-conformity.13 Annex A (normative)
Chemical composition and mechanical properties of EN AC-AIZn10Si8Mg.14 Annex B (informative)
Guidelines for application and use.17 B.1 Selection of alloys.17 B.2 Fatigue Design.17 B.3 Welding.17
EN 13981-3:2006 (E) 3 Bibliography.18
EN 13981-3:2006 (E) 4 Foreword This document (EN 13981-3:2006) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2007, and conflicting national standards shall be withdrawn at the latest by March 2007. Within its program of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 21 "Aluminium for railway applications" to prepare the following standard : EN 13981-3, Aluminium and aluminium alloys – Products for structural railway applications — Technical conditions for inspection and delivery – Part 3 : Castings. "EN 13981 comprises the following parts under the general title "Aluminium and aluminium alloys – Products for structural railway applications – Technical conditions for inspection and delivery". Part 1 : Extruded products Part 2 : Plates and sheets Part 3 : Castings Part 4 : Forgings Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 13981-3:2006 (E) 5 1 Scope This document specifies requirements for castings which contribute to the structural properties of the railcar bodyshell and other major structural components. It specifies particular requirements regarding qualification, quality control, material properties and dimensional tolerances and gives guide-lines for application and use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 444, Non-destructive testing – General principles for radiographic examination of metallic materials by X- and gamma-rays EN 462-1, Non-destructive testing – Image quality of radiographs – Part 1: Image quality indicators (wire type) – Determination of image quality value EN 473, Non destructive testing – Qualification and certification of NDT personnel – General principles EN 571-1, Non destructive testing – Penetrant testing – Part 1: General principles EN 895, Destructive tests on welds in metallic materials – Transverse tensile test EN 1011-4, Welding – Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys EN 1371-1, Founding - Liquid penetrant inspection – Part 1: Sand, gravity die and low pressure die castings EN 1559-1, Founding – Technical conditions of delivery – Part 1: General EN 1559-4, Founding – Technical conditions of delivery – Part 4: Additional requirements for aluminium alloy castings EN 1706:1998, Aluminium and aluminium alloys – Castings – Chemical compositions and mechanical properties EN 10204, Metallic products – Types of inspection documents. EN 12258-1:1998, Aluminium and aluminium alloys – Terms and definitions – Part 1: General terms EN 12681, Founding – Radiographic examination EN ISO 9606-2, Qualification test of welders – Fusion welding – Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) EN ISO 10042, Welding - Arc-welded joints in aluminium and its alloys – Quality levels for imperfections (ISO 10042:2005)
EN 13981-3:2006 (E) 6 EN ISO 15614-4, Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 4: Finishing welding of aluminium castings (ISO 15614-4:2005) ISO 5579, Non-destructive testing – Radiographic examination of metallic materials by X- and gamma-rays – Basic rules ISO 8062, Castings – System of dimensional tolerances and machining allowances ASTM-E 155 Standard, Reference Radiographs for Inspection of Aluminium and Magnesium Castings 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 cast quantity of products of the same shape and cast from the same melt 3.2 inspection lot consignment, or part thereof, submitted for inspection, comprising products of the same grade or alloy, form, temper, size, shape, thickness or cross-section and processed in the same manner 3.3 structural property property having a direct effect on the static and dynamic load carrying capability of a component or assembly 4 Ordering information The order shall define the product required for structural applications and shall contain the following information: a) designation of the aluminium alloy and temper according to EN 1706; b) drawing of casting including the following indications: area for X-ray-testing and the relevant acceptance criteria according to ASTM-E 155; acceptance criteria for surface imperfections according to EN 1371-1; c) reference to this European Standard (EN 13981-3); d) quantity: total mass or number of pieces; tolerances on quantity if required; e) any requirements for certificates of conformity, test and/or analysis reports or inspection certificates; f) any additional requirements agreed between supplier and purchaser. If special requirements are stated in the order agreed between supplier and purchaser which differ from requirements specified or referenced in this document, then these special requirements shall apply.
EN 13981-3:2006 (E) 7 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified on the order, the production and manufacturing processes shall be left to the manufacturer’s discretion. Any modification of the production process qualified by the first-off procedure (see 6.1), which can affect the quality of the product shall be reported to and approved by the purchaser. In specific cases, a new first-off approval can be necessary. Unless it is explicitly stated on the order, no obligation shall be placed on the manufacturer to use the same processes for subsequent and similar orders. 5.2 Quality assurance The manufacturer shall establish and maintain a quality management system which should be at least equivalent to EN ISO 9001. Furthermore, the ordering railway company may require a formal approval of the manufacturer according to a specified procedure. The manufacturer shall establish and maintain inspection plans defining all inspections and tests to be performed on the product, the frequency of the inspections and tests and the type of record to be established. The inspection plan shall specify for each inspection or test whether it is to be performed per cast, per heat treatment batch, per inspection lot or per any other lot of importance. The inspection plan shall conform as a minimum to the test procedures and test requirements stipulated in this standard. The inspection plan shall include additional schemes for appropriate process control. If required the inspection plan shall be submitted to the purchaser for approval before the start of production. The manufacturer shall be responsible for carrying out all inspections and tests required by this standard prior to the shipment of the product. If the purchaser wishes to inspect the product at the manufacturer's works, he or she shall stipulate this at the time of order. The extent of inspections shall be in accordance with Table 1. Unless explicitly stated, quality controls and inspections shall be performed on cast and/
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.