SIST EN ISO 12625-3:2005

Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2005)

This part of prEN 12625 specifies a test method for the determination of thickness, bulking thickness and apparent bulk density of tissue papers and tissue products when under a specified pressure of 2,0 kPa. Note: This European Standard has been developed to provide a consistent test method for the determination of certain properties of tissue paper and tissue products. Corresponding test methods for paper and board in general are covered in EN 20534.

Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung der Dicke, der Blattdicke im Stapel und der scheinbaren Stapeldichte (ISO 12625-3:2005)

Dieser Teil der ISO 12625 legt ein Prüfverfahren zur Bestimmung der Dicke, der Blattdicke im Stapel und der scheinbaren Stapeldichte von Tissue-Papieren und Tissue-Produkten fest, die einem speziellen Anpressdruck von 2,0 kPa ausgesetzt werden.
ANMERKUNG   Dieser Teil der ISO 12625 wurde erarbeitet, um ein in sich geschlossenes Prüfverfahren zur Bestimmung der Dicke und Dichte von Tissue-Papier und Tissue-Produkten anzubieten. Ähnliche Prüfverfahren für allgemeine Papiere und Pappen werden nach ISO 534 geprüft.
Darüber hinaus wird ausdrücklich darauf hingewiesen, dass zur Erkennung von Unreinheiten und Verunreinigungen in Tissue-Papier und Tissue-Produkten ISO 15755 angewendet werden sollte.
Für die Bestimmung des Feuchtegehaltes in Tissue-Papier und Tissue-Produkten sollte ISO 287 angewendet werden.

Papier tissu et produits en tissu - Partie 3: Détermination de l'épaisseur, de l'épaisseur moyenne d'une feuille en liasse et de la masse volumique moyenne (ISO 12625-3:2005)

Cette partie de prEN 12625 spécifie une méthode d'essai pour la détermination de l'épaisseur des feuilles uniques ou des feuilles en liasse et de la masse volumique apparente de papiers tissu et de produits tissu sous une pression spécifique de 2,0 kPa. Note: Cette norme européenne a été mise au point pour que l'on dispose d'une méthode appropriée pour la détermination de certaines propriétés du papier tissu et des produits tissu. Les méthodes d'essai correspondantes pour le papier et le carton sont traitées dans EN 20534.

Tissue papir in proizvodi iz tissue papirja - 3. del: Ugotavljanje debeline, specifičnega volumna in prostorninske mase (ISO 12625-3:2005)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2005
• Withdrawal Date: 04-Aug-2014
• ICS: 85.080.20 - Tissue paper
• Technical Committee: VPK - Pulp, paper, board and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Aug-2014
• Due Date: 28-Aug-2014
• Completion Date: 05-Aug-2014
• Ref Project: EN ISO 12625-3:2005 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2005)

Relations

• Replaced By: SIST EN ISO 12625-3:2014 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2014)
• Effective Date: 01-Sep-2014
• Replaced By: SIST EN ISO 12625-3:2014 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2014)
• Effective Date: 08-Jun-2022
• Replaces: SIST EN 12625-3:2000 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density
• Effective Date: 01-Jul-2005

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12625-3:2005
01-julij-2005
1DGRPHãþD
SIST EN 12625-3:2000
7LVVXHSDSLULQSURL]YRGLL]WLVVXHSDSLUMDGHO8JRWDYOMDQMHGHEHOLQH
VSHFLILþQHJDYROXPQDLQSURVWRUQLQVNHPDVH,62
Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness
and apparent bulk density (ISO 12625-3:2005)
Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung der Dicke, der Blattdicke im
Stapel und der scheinbaren Stapeldichte (ISO 12625-3:2005)
Papier tissu et produits en tissu - Partie 3: Détermination de l'épaisseur, de l'épaisseur
moyenne d'une feuille en liasse et de la masse volumique moyenne (ISO 12625-3:2005)
Ta slovenski standard je istoveten z: EN ISO 12625-3:2005
ICS:
85.080.20 Tissue papir Tissue paper
SIST EN ISO 12625-3:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12625-3:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 12625-3:2005



EUROPEAN STANDARD
EN ISO 12625-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2005
ICS 85.060 Supersedes EN 12625-3:1999
English version
Tissue paper and tissue products - Part 3: Determination of
thickness, bulking thickness and apparent bulk density (ISO
12625-3:2005)
Papier tissu et produits en tissu - Partie 3: Détermination Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung
de l'épaisseur, de l'épaisseur moyenne d'une feuille en der Dicke, der Blattdicke im Stapel und der scheinbaren
liasse et de la masse volumique moyenne (ISO 12625- Stapeldichte (ISO 12625-3:2005)
3:2005)
This European Standard was approved by CEN on 15 March 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12625-3:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12625-3:2005
EN ISO 12625-3:2005 (E)




Foreword



This document (EN ISO 12625-3:2005) has been prepared by Technical Committee CEN/TC 172 "Pulp,
paper and board", the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC
6 "Paper, board and pulps”.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn
at the latest by October 2005.

This document supersedes EN 12625-3:1999.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12625-3:2005

INTERNATIONAL ISO
STANDARD 12625-3
First edition
2005-04-15


Tissue paper and tissue products —
Part 3:
Determination of thickness, bulking
thickness and apparent bulk density
Papier tissu et produits en tissu —
Partie 3: Détermination de l'épaisseur, de l'épaisseur moyenne d'une
feuille en liasse et de la masse volumique moyenne





Reference number
ISO 12625-3:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 12625-3:2005
ISO 12625-3:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 12625-3:2005
ISO 12625-3:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle . 2
5 Apparatus. 2
6 Conditioning . 3
7 Preparation of test pieces . 3
8 Procedure. 4
9 Calculation. 4
10 Test report. 5
11 Precision . 5
Annex A (normative) Measurement conditions. 7
Annex B (informative) Foot pressure . 9
Bibliography . 10

© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 12625-3:2005
ISO 12625-3:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12625-3 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 172, Pulp, paper and board, in collaboration with Technical Committee ISO/TC 6, Paper, board and
pulps, Subcommittee SC 2, Test methods and quality specifications for paper and board, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This first edition cancels and replaces EN 12625-3:1999, which has been technically revised.
With regard to EN 12625-3:1999, the following changes have been made:
a) more precise definitions;
b) more precise description of the apparatus;
c) preparation of test pieces more precisely described;
d) editorial updating.
ISO 12625 consists of the following parts, under the general title Tissue paper and tissue products:
 Part 1: General guidance on terms
 Part 3: Determination of thickness, bulking thickness and apparent bulk density
 Part 4: Determination of tensile strength, stretch at break and tensile energy absorption
 Part 5: Determination of wet tensile strength
 Part 6: Determination of grammage
 Part 7: Determination of optical properties
 Part 8: Water absorption time and water absorption capacity, basket immersion test method
 Part 9: Determination of ball burst strength
iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12625-3:2005
ISO 12625-3:2005(E)
Introduction
Thickness is an important property of tissue paper and tissue products.
In the tissue industry, thickness-related parameters, such as the roll diameter of rolled products (kitchen towel)
or the stack height of folded products (paper towels) are often measured. However, the fact that not only
end-use tissue products, but also the base tissue paper from which these products are made, is the subject of
trade between companies and countries, means that there is a genuine need for a consistent measure of
thickness that can be applied to tissue products at any stage of their manufacture.
The thickness of tissue paper and tissue products is known to be dependent on the pressure applied to the
material at the time of measurement. Several different loading pressures, pressure-foot diameters and loading
speeds have been used within the tissue industry. This part of ISO 12625 has been prepared by harmonising
those standards applicable to tissue and tissue products currently in use. It specifies a single loading pressure,
foot diameter and loading speed to be used for all thickness measurements of tissue and tissue products.
© ISO 2005 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 12625-3:2005

---------------------- Page: 10 ----------------------

SIST EN ISO 12625-3:2005
INTERNATIONAL STANDARD ISO 12625-3:2005(E)

Tissue paper and tissue products —
Part 3:
Determination of thickness, bulking thickness and apparent
bulk density
1 Scope
This part of ISO 12625 specifies a test method for the determination of thickness and bulking thickness, and
the calculation of apparent bulk density, of tissue paper and tissue products under a pressure of 2,0 kPa.
NOTE This part of ISO 12625 has been developed to provide a consistent test method for the determination of
thickness and density of tissue paper and tissue products. Corresponding test methods for paper and board in general are
covered in ISO 534.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products should
be applied according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 should be applied.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 186, Paper and board — Sampling to determine average quality
ISO 187, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 12625-1, Tissue paper and tissue products — Part 1: General guidance on terms
ISO 12625-6, Tissue paper and tissue products — Part 6: Determination of grammage
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12625-1 and the following apply.
3.1
single-ply thickness
distance between the two principal surfaces of a single ply of tissue paper measured under the applied static
load specified in this part of ISO 12625
NOTE A “ply” of tissue is an unlaminated tissue, like that made directly from a tissue machine.
© ISO 2005 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 12625-3:2005
ISO 12625-3
...