SIST EN ISO 10309:2016
(Main)Metallic coatings - Porosity tests - Ferroxyl test (ISO 10309:1994)
Metallic coatings - Porosity tests - Ferroxyl test (ISO 10309:1994)
This International Standard specifies a method of revealing pores or other discontinuities, when testing metallic coatings, that are not visibly affected by ferricyanide and chloride ions during the test period and that are cathodic to iron and steel. This method is especially useful for thick, hard chromium coatings used for wear resistance.
NOTE 1 With some coating materials a very thin layer is dissolved by the sodium chloride solution during a 10 minute application period (see 5.2.3). The impact of such dissolution is that potential porosity, i.e. pores that have been covered over by very thin layers, are sometimes re-exposed. Experience has shown that such potential porosity is frequently re-exposed during actual service.
Metallische Überzüge - Prüfverfahren zur Bestimmung der Porosität - Ferroxylprüfung (ISO 10309:1994)
Diese Internationale Norm legt ein Verfahren zum Erkennen von Poren oder anderen Fehlstellen bei der
Prüfung metallischer Überzüge fest, die während der Prüfdauer durch Hexacyanoferrat- und Chlorionen
nicht erkennbar beeinträchtigt werden und die sich gegenüber Eisen und Stahl kathodisch verhalten. Dieses
Verfahren ist besonders für dicke, harte Chromüberzüge, die zur Verbesserung der Verschleißbeständigkeit
dienen, geeignet.
ANMERKUNG 1 Bei einigen Überzugswerkstoffen löst die Natriumchloridlösung innerhalb einer 10-minütigen
Anwendungsdauer (siehe 5.2.3) eine sehr dünne Schicht auf. Diese Auflösung bewirkt, dass eine mögliche Porosität, d. h.
von sehr dünnen Schichten überdeckte Poren, manchmal wieder freigelegt wird. Erfahrungsgemäß wird diese mögliche
Porosität häufig beim tatsächlichen Einsatz wieder freigelegt.
Revêtements métalliques - Essais de porosité - Essai au ferroxyle (ISO 10309:1994)
L'IEC 60194:2015 définit la terminologie utilisée dans le domaine des cartes de circuits imprimés et des produits d'assemblage de cartes de circuits imprimés. Les principaux changements par rapport à l'édition précédente sont les suivantes:
- Quelque deux cents termes et définitions ont été mis à jour, le cas échéant, et
- deux cents nouveaux termes et définitions ont été ajoutés.
Kovinske prevleke - Preskus ugotavljanja poroznosti - Preskus ferroxyl (ISO 10309:1994)
Ta mednarodni standard določa metodo odkrivanja por ali drugih prekinitev pri preskušanju kovinskih prevlek, na katere med preskusnim obdobjem nimajo vidnega vpliva fericianidni in kloridni ioni, ki delujejo katodno na železo in jeklo. Ta metoda je zlasti uporabna za debele prevleke iz trdega kroma, ki se uporabljajo za odpornost na obrabo. OPOMBA 1: Med 10-minutnim obdobjem uporabe nekaterih prevlečnih materialov (glej točko 5.2.3) raztopina natrijevega klorida povzroči raztopitev zelo tanke plasti. Zaradi te raztopitve se možna porozivnost oz. pore, ki jih prekrijejo zelo tanke plasti, včasih znova pojavijo. Izkušnje so pokazale, da se ta možna porozivnost pogosto znova pojavi med dejansko uporabo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10309:2016
01-julij-2016
1DGRPHãþD
SIST ISO 10309:1999
Kovinske prevleke - Preskus ugotavljanja poroznosti - Preskus ferroxyl (ISO
10309:1994)
Metallic coatings - Porosity tests - Ferroxyl test (ISO 10309:1994)
Metallische Überzüge - Prüfverfahren zur Bestimmung der Porosität - Ferroxylprüfung
(ISO 10309:1994)
Revêtements métalliques - Essais de porosité - Essai au ferroxyle (ISO 10309:1994)
Ta slovenski standard je istoveten z: EN ISO 10309:2016
ICS:
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 10309:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10309:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 10309:2016
EN ISO 10309
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2016
EUROPÄISCHE NORM
ICS 25.220.40
English Version
Metallic coatings - Porosity tests - Ferroxyl test
(ISO 10309:1994)
Revêtements métalliques - Essais de porosité - Essai au Metallische Überzüge - Prüfverfahren zur Bestimmung
ferroxyle (ISO 10309:1994) der Porosität - Ferroxylprüfung (ISO 10309:1994)
This European Standard was approved by CEN on 2 April 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10309:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10309:2016
EN ISO 10309:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10309:2016
EN ISO 10309:2016 (E)
European foreword
The text of ISO 10309:1994 has been prepared by Technical Committee ISO/TC 107 “Metallic and other
inorganic coatings” of the International Organization for Standardization (ISO) and has been taken over
as EN ISO 10309:2016 by Technical Committee CEN/TC 262 “Metallic and other inorganic coatings” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10309:1994 has been approved by CEN as EN ISO 10309:2016 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10309:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 10309:2016
ISO
INTERNATIONAL
10309
STANDARD
First edition
1994-12-01
Metallic coatings - Porosity tests -
Ferroxyl test
ßedtements mktalliques - Essais de porositk - Essai au ferroxyle
Reference number
ISO 10309:1994(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 10309:2016
ISO 10309:1994(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 10309 was prepared by Technical Committee
lSO/TC 107, MetaNc and other inorganic coatings, Subcommittee SC 7,
Corrosion tests.
0 ISO 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronrc or mechanrcal, including photocopyrng and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 0 Switzerland
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 10309:2016
~~~~
INTERNATIONAL STANDARD 0 ISO ISO 10309:1994(E)
- Porosity tests - Ferroxyl test
Metallic coatings
tom of discontinuities in metallic coatings migrate to
1 Scope
treated test Paper held in contact with the coating
surface. The bas
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kovinske prevleke - Preskus ugotavljanja poroznosti - Preskus ferroxyl (ISO 10309:1994)Metallische Überzüge - Prüfverfahren zur Bestimmung der Porosität - Ferroxylprüfung (ISO 10309:1994)Revêtements métalliques - Essais de porosité - Essai au ferroxyle (ISO 10309:1994)Metallic coatings - Porosity tests - Ferroxyl test (ISO 10309:1994)25.220.40Kovinske prevlekeMetallic coatingsICS:Ta slovenski standard je istoveten z:FprEN ISO 10309kSIST FprEN ISO 10309:2015en,fr,de01-december-2015kSIST FprEN ISO 10309:2015SLOVENSKI
STANDARDSIST ISO 10309:19991DGRPHãþD
kSIST FprEN ISO 10309:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 10309
October
t r s w ICS
t wä t t rä v r English Version
Revêtements métalliques æ Essais de porosité æ Essai au
Metallische Überzüge æ Prüfverfahren zur Bestimmung This draft European Standard is submitted to CEN members for unique acceptance procedureä It has been drawn up by the
If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä
This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä
Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä FprEN ISO
s r u r {ã t r s w EkSIST FprEN ISO 10309:2015
FprEN ISO 10309:2015 (E) 2 Contents Page European foreword . 3 kSIST FprEN ISO 10309:2015
FprEN ISO 10309:2015 (E) 3 European foreword The text of ISO 10309:1994 has been prepared by Technical Committee ISO/TC 107 “Metallic and other inorganic coatings” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 10309:2015 by Technical Committee CEN/TC 262 “Metallic and other inorganic coatings” the secretariat of which is held by BSI. This document is currently submitted to the Unique Acceptance Procedure. Endorsement notice The text of ISO 10309:1994 has been approved by CEN as FprEN ISO 10309:2015 without any modification. kSIST FprEN ISO 10309:2015
kSIST FprEN ISO 10309:2015
INTERNATIONAL STANDARD ISO 10309 First edition 1994-12-01 Metallic coatings - Porosity tests - Ferroxyl test ßedtements mktalliques - Essais de porositk - Essai au ferroxyle Reference number ISO 10309:1994(E) kSIST FprEN ISO 10309:2015
ISO 10309:1994(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10309 was prepared by Technical Committee lSO/TC 107, MetaNc and other inorganic coatings, Subcommittee SC 7, Corrosion tests. 0 ISO 1994 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronrc or mechanrcal, including photocopyrng and microfilm, without Permission in writing from the publisher. International Organization for Standardization Case Postale 56 l CH-l 211 Geneve 20 0 Switzerland Printed in Switzerland ii kSIST FprEN ISO 10309:2015
~~~~ INTERNATIONAL STANDARD 0 ISO ISO 10309:1994(E) Metallic coatings - Porosity tests - Ferroxyl test 1 Scope This International Standard specifies a method of re- vealing pores or other discontinuities, when testing metallic coatings, that are not visibly affected by ferricyanide and chloride ions during the test period and that are cathodic to iron and steel. This method is especially useful for thick, hard chromium coatings used for wear resistance. NOTE 1 With some coating materials a very thin layer is dissolved by the sodium chloride Solution during a 10 min- ute application period (see 5.2.3). The impact of such dis- Solution is that potential porosity, i.e. pores that have been covered over by very thin layers, are sometimes re-exposed. Experience has shown that such potential
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.