SIST EN ISO 12162:2010
(Main)Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
This International Standard establishes the classification of thermoplastics materials in pipe form and specifies the material designation. It also specifies a method for calculating the design stress. It is applicable to materials intended for pipes and fittings for pressure applications. NOTE 1 Classification, minimum design coefficient and calculation method are based on the resistance to internal pressure with water at 20 °C for 50 years, derived by extrapolation using the method given in ISO 9080. NOTE 2 Design coefficients for multilayer pipes are described in the appropriate product (system) standards.
Thermoplastische Werkstoffe für Rohre und Formstücke für Anwendungen unter Druck - Klassifizierung, Gesamtbetriebs-(berechnungs-)Koeffizient und Werkstoffkennzeichnung (ISO 12162:2009)
Diese internationale Norm beschreibt die Klassifizierung von thermoplastischen Werkstoffen in Gestalt eines
Rohres und legt die Anforderungen an die Werkstoffkennzeichnung fest. Sie enthält außerdem ein Verfahren
zur Berechnung der Betriebsspannung.
Sie ist auf Werkstoffe, die für Rohre und Formstücke für Anwendungen unter Druck vorgesehen sind,
anwendbar.
ANMERKUNG 1 Die Klassifizierung, der kleinste Gesamtbetriebs-(berechnungs-)Koeffizient und das Berechnungsverfahren
beruhen auf der Widerstandsfähigkeit gegen Innendruck, hergeleitet nach dem Extrapolationsverfahren nach
ISO 9080 für 50 Jahre bei 20 °C in Wasser.
ANMERKUNG 2 Die Gesamtbetriebs-(berechnungs-)Koeffizienten für Mehrschichtverbundrohre sind in den entsprechenden
Produkt-(System-)Normen beschrieben.
Matières thermoplastiques pour tubes et raccords pour applications avec pression - Classification, coefficient de calcul et désignation (ISO 12162:2009)
L'ISO 12162:2009 établit une classification des matières thermoplastiques sous forme de tube et spécifie la désignation des matières. Elle spécifie également une méthode de détermination de la contrainte de calcul.
L'ISO 12162:2009 s'applique aux matières destinées aux tubes et aux raccords pour applications avec pression.
Plastomerni materiali za cevi in fitinge v tlačnih cevovodih - Razvrščanje, označevanje in skupni koeficient za projektiranje (ISO 12162:2009)
Ta mednarodni standard vzpostavlja klasifikacijo plastomernih materialov v cevasti obliki in določa označevanje materialov. Določa tudi metodo za izračun projektne obremenitve. Velja za materiale za cevi in fitinge v tlačnih cevovodih. OPOMBA 1: Klasifikacija, minimalni koeficient za projektiranje in metoda izračunavanja temeljijo na upornosti proti notranjemu tlaku vode pri 20 °C za 50 let, ki se izračuna z ekstrapolacijo po metodi, podani v ISO 9080. OPOMBA 2: Koeficienti za projektiranje večplastnih cevi so opisani v ustreznih standardih za proizvode (sisteme).
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.]YUãþDQMHThermoplastische Werkstoffe für Rohre und Formstücke für Anwendungen unter Druck - Klassifizierung, Gesamtbetriebs-(berechnungs-)Koeffizient und Werkstoffkennzeichnung (ISO 12162:2009)Matières thermoplastiques pour tubes et raccords pour applications avec pression - Classification, coefficient de calcul et désignation (ISO 12162:2009)Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)23.040.45Fitingi iz polimernih materialovPlastics fittings23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN ISO 12162:2009SIST EN ISO 12162:2010en01-marec-2010SIST EN ISO 12162:2010SLOVENSKI
STANDARDSIST EN ISO 12162:19971DGRPHãþD
SIST EN ISO 12162:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12162
November 2009 ICS 23.040.20; 23.040.45 Supersedes EN ISO 12162:1995English Version
Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
Matières thermoplastiques pour tubes et raccords pour applications avec pression - Classification, désignation et coefficient de calcul (ISO 12162:2009)
Thermoplastische Werkstoffe für Rohre und Formstücke für Anwendungen unter Druck - Klassifizierung, Gesamtbetriebs-(berechnungs-)Koeffizient und Werkstoffkennzeichnung (ISO 12162:2009) This European Standard was approved by CEN on 10 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12162:2009: ESIST EN ISO 12162:2010
EN ISO 12162:2009 (E) 2 Contents Page Foreword .3 SIST EN ISO 12162:2010
EN ISO 12162:2009 (E) 3 Foreword This document (EN ISO 12162:2009) has been prepared by Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 12162:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 12162:2009 has been approved by CEN as a EN ISO 12162:2009 without any modification.
SIST EN ISO 12162:2010
SIST EN ISO 12162:2010
Reference numberISO 12162:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO12162Second edition2009-11-15Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient Matières thermoplastiques pour tubes et raccords pour applications avec pression — Classification, désignation et coefficient de calcul
SIST EN ISO 12162:2010
ISO 12162:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
SIST EN ISO 12162:2010
ISO 12162:2009(E) © ISO 2009 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12162 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories — Test methods and basic specifications. This second edition cancels and replaces the first edition (ISO 12162:1995), which has been technically revised. SIST EN ISO 12162:2010
ISO 12162:2009(E) iv © ISO 2009 – All rights reserved Introduction The revision of this International Standard incorporates the introduction of a CRSθ,t value (categorized required strength at a temperature θ and time t), in addition to the MRS classification and the introduction of minimum design coefficients for additional materials. The classification in this International Standard does not qualify a material for a specific application. For specific applications, the relevant product standards require that additional mechanical and physical properties be met. SIST EN ISO 12162:2010
INTERNATIONAL STANDARD ISO 12162:2009(E) © ISO 2009 – All rights reserved 1 Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient 1 Scope This International Standard establishes the classification of thermoplastics materials in pipe form and specifies the material designation. It also specifies a method for calculating the design stress. It is applicable to materials intended for pipes and fittings for pressure applications. NOTE 1 Classification, minimum design coefficient and calculation method are based on the resistance to internal pressure with water at 20 °C for 50 years, derived by extrapolation using the method given in ISO 9080. NOTE 2 Design coefficients for multilayer pipes are described in the appropriate product (system) standards. 2 Normative references The following referenced documents are indispensable for the applicati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.