iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 334:2000

(Main)

Gas pressure regulators for inlet pressures up to 100 bar

Gas pressure regulators for inlet pressures up to 100 bar

This European Standard specifies constructional and functional requirements, regulator sizing, testing, documentation and marking of gas pressure regulators: - for inlet pressures up to 100 bar, - used at an ambient temperature range from -20°C to +60°C which operate with fuel gases of the 1st and of the 2nd family in accordance with EN 437 in transmission and distribution networks and also in industrial installations. "Gas pressure regulators" hereafter will be called "regulators" except in the titles.

Gas-Druckregelgeräte für Eingangsdrücke bis 100 bar

Diese Europäische Norm legt die Anforderungen an Bauweise, Funktionsverhalten, Dimensionierung, Prüfung, Dokumentation und Kennzeichnung von Gas-Druckregelgeräten fest für: - Eingangsdrücke bis 100 bar, - Umgebungstemperaturen von -20°C bis +60°C, soweit sie mit Brenngasen der 1. und 2. Familie nach EN 437 in Gasversorgungsnetzen wie auch in industriellen Anlagen betrieben werden. " Gas-Druckregelgeräte" werden nachfolgend, außer in den Überschriften, als "Regelgeräte" bezeichnet.

Appareils de régulation de pression de gaz (régulateurs) pour des pressions amont jusqu'a 100 bar

La présente norme européenne spécifie les exigences relatives a la construction et au fonctionnement, au dimensionnement, aux essais, a la documentation et au marquage des appareils de régulation de pression (régulateurs). Il concerne les régulateurs: - pour une pression amont jusqu'a 100 bar; - pour une plage de température ambiante de -20°C a +60°C qui sont exploités avec des gaz combustibles de la premiere et de la deuxieme famille conformément a l'EN 437 dans les réseaux de transport et de distribution ainsi que dans les installations industrielles.

Regulatorji tlaka plina za vstopne tlake do 100 bar

General Information

Status
Withdrawn
Publication Date
31-Jan-2000
Withdrawal Date
31-May-2005
ICS
23.060.40 - Pressure regulators
Technical Committee
DPL - Gas supply
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jun-2005
Due Date
01-Jun-2005
Completion Date
01-Jun-2005
Ref Project
EN 334:1999 - Gas pressure regulators for inlet pressures up to 100 bar

Relations

Amended By
SIST EN 334:2000/A1:2003 - Gas pressure regulators for inlet pressures up to 100 bar
Effective Date
22-Dec-2008
Replaced By
SIST EN 334:2005 - Gas pressure regulators for inlet pressures up to 100 bar
Effective Date
01-Jun-2005

Buy Standard

EN 334:2000EN 334:2000
PreviousNext
Standard
EN 334:2000
English language
65 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Regulatorji tlaka plina za vstopne tlake do 100 barGas-Druckregelgeräte für Eingangsdrücke bis 100 barAppareils de régulation de pression de gaz (régulateurs) pour des pressions amont jusqu'a 100 barGas pressure regulators for inlet pressures up to 100 bar23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 334:1999SIST EN 334:2000en01-februar-2000SIST EN 334:2000SLOVENSKI
STANDARD



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



SIST EN 334:2000



...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 14382:2019(Main)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
EN 14382:2019

This document specifies constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations in accordance with EN 12186 or EN 12279:
- for inlet pressures up to 100 bar and nominal diameters up to DN 400;
- for an operating temperature range from –20 °C to +60 °C,
which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 334:2019(Main)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
EN 334:2019

This document specifies constructional, functional, testing and marking requirements, sizing and
documentation of gas pressure regulators used in the pressure regulating stations in accordance with
EN 12186 or EN 12279:
- for inlet pressures up to 100 bar and nominal diameters up to DN 400;
- for an operating temperature range from -20 °C to +60 °C,
which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and
distribution networks and also in commercial and industrial installations.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12186:2015(Main)
Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
EN 12186:2014

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flowrate is equal to or less than 200 m³/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorisation systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European standard are based on the physical and chemical data of gaseous fuels - including non-conventional gases - in accordance with Table 1 of EN 437:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.
This European Standard specifies common basic principles for the gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation shall take precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 gives:
-  clarification of all legislations/regulations applicable in a member state;
-  if appropriate, more restrictive national requirements;
-  a national contact point for the latest information.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12279:2000/A1:2005(Amendment)
Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements
EN 12279:2000/A1:2005
  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12279:2000(Main)
Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements
EN 12279:2000

This European Standard contains the relevant functinal requirements for gas pressure regulating installations forming a part of the service lines in gas supply systems.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 334:2019/oprA1:2023(Amendment)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
EN 334:2019/prA1

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 334:2005/kprA1:2008(Amendment)
Gas pressure regulators for inlet pressures up to 100 bar
EN 334:2005/prA1

Tolerance of 9 months requested before UAP per CEN/TC 235 C02/2006.

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14382:2019/kFprA1:2023(Amendment)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
EN 14382:2019/FprA1

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14382:2005/kprA1:2008(Amendment)
Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
EN 14382:2005/prA1

Tolerance of 9 months before UAP per CEN/TC 235 res. C03/2006.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 407:2023(Main)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)
EN ISO 407:2023

This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with a working pressure up to a maximum of 200 bar or test pressure up to a maximum of 300 bar, or both.
NOTE 1    This type of connection is primarily used for small cylinders (5 l or below).
NOTE 2    In this document the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa (1 bar = 105 Pa = 105 N/m2).
This document specifies:
—    basic dimensions;
—    requirements for alternative designs of the yoke-type valve connections;
—    dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for gases and gas mixtures.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day