SIST EN 60086-2:2016

Primary batteries - Part 2: Physical and electrical specifications

This part of IEC 60086 is applicable to primary batteries based on standardized electrochemical
systems.
It specifies
– the physical dimensions,
– the discharge test conditions and discharge performance requirements.

Primärbatterien - Teil 2: Physikalische und elektrische Spezifikationen

Piles électriques - Partie 2: Spécifications physiques et électriques

L'IEC 60086-2:2015 est applicable aux piles fonctionnant avec des systèmes électrochimiques normalisés. Elle spécifie les dimensions physiques, les conditions d'essai de décharge et les spécifications de performance de décharge. Cette treizième édition annule et remplace la douzième édition (2011) dont elle constitue une révision technique. Les modifications majeures par rapport à l'édition précédente sont des modifications relatives aux essais des piles de type R03, LR03, R6, LR6, PR70, PR41, PR48, 6F22, 6LR61, 6LP3146 4LR25-2, R14, LR14, R20, LR20, CR2025 et CR2032, la réintégration du type de pile 5AR40 dans la norme, l'ajout de désignations communes, l'ajout des deux nouveaux types de piles FR14505 et FR10G445, la suppression des types de piles LR53, R40, 2EP3863 et 6F100, et des modifications éditoriales générales.
Mots clés: piles électriques, systèmes électrochimiques

Primarne baterije - 2. del: Specifikacije fizikalnih in električnih veličin

Ta del standarda IEC 60086 se uporablja za primarne baterije na osnovi standardiziranih elektrokemičnih
sistemov.
Določa:
– fizične mere,
– preskusne pogoje praznjenja in zahteve zmogljivosti praznjenja.

General Information

• Status: Published
• Publication Date: 09-Mar-2016
• ICS: 29.220.10 - Primary cells and batteries
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 02-Mar-2016
• Due Date: 07-May-2016
• Completion Date: 10-Mar-2016
• Ref Project: EN 60086-2:2016 - Primary batteries - Part 2: Physical and electrical specifications

Relations

• Replaced By: SIST EN IEC 60086-2:2021 - Primary batteries - Part 2: Physical and electrical specifications (IEC 60086-2:2021)
• Effective Date: 15-Jun-2021
• Revised: SIST EN IEC 60086-2:2021 - Primary batteries - Part 2: Physical and electrical specifications (IEC 60086-2:2021)
• Effective Date: 25-Jul-2017
• Replaces: SIST EN 60086-2:2011 - Primary batteries - Part 2: Physical and electrical specifications (IEC 60086-2:2011)
• Effective Date: 01-Apr-2016
• Replaces: SIST EN 60086-2:2011 - Primary batteries - Part 2: Physical and electrical specifications (IEC 60086-2:2011)
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60086-2:2016
01-april-2016
1DGRPHãþD
SIST EN 60086-2:2011
3ULPDUQHEDWHULMHGHO6SHFLILNDFLMHIL]LNDOQLKLQHOHNWULþQLKYHOLþLQ
Primary batteries - Part 2: Physical and electrical specifications
Primärbatterien - Teil 2: Physikalische und elektrische Spezifikationen
Piles électriques - Partie 2: Spécifications physiques et électriques
Ta slovenski standard je istoveten z: EN 60086-2:2016
ICS:
29.220.10 3ULPDUQLþOHQLLQEDWHULMH Primary cells and batteries
SIST EN 60086-2:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60086-2:2016

---------------------- Page: 2 ----------------------

SIST EN 60086-2:2016


EUROPEAN STANDARD EN 60086-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2016
ICS 29.220.10 Supersedes EN 60086-2:2011
English Version
Primary batteries - Part 2: Physical and electrical specifications
(IEC 60086-2:2015)
Piles électriques - Partie 2: Spécifications physiques et Primärbatterien - Teil 2: Physikalische und elektrische
électriques Spezifikationen
(IEC 60086-2:2015) (IEC 60086-2:2015)
This European Standard was approved by CENELEC on 2015-12-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60086-2:2016 E

---------------------- Page: 3 ----------------------

SIST EN 60086-2:2016
EN 60086-2:2016
European foreword
The text of document 35/1350/FDIS, future edition 13 of IEC 60086-2, prepared by IEC/TC 35
"Primary cells and batteries" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60086-2:2016.
The following dates are fixed:
(dop) 2016-09-03
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2018-12-03
the document have to be withdrawn

This document supersedes EN 60086-2:2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60086-2:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated :
IEC 60086-3 NOTE Harmonized as EN 60086-3.
IEC 60086-4 NOTE Harmonized as EN 60086-4.
IEC 60086-5 NOTE Harmonized as EN 60086-5.
IEC 62281 NOTE Harmonized as EN 62281.
2

---------------------- Page: 4 ----------------------

SIST EN 60086-2:2016
EN 60086-2:2016

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60086-1 2015 Primary batteries - Part 1: General EN 60086-1 2015
ISO 1101 -  Geometrical product specifications (GPS) - EN ISO 1101 -
Geometrical tolerancing - Tolerances of
form, orientation, location and run-out

3

---------------------- Page: 5 ----------------------

SIST EN 60086-2:2016

---------------------- Page: 6 ----------------------

SIST EN 60086-2:2016



IEC 60086-2

®


Edition 13.0 2015-10




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Primary batteries –

Part 2: Physical and electrical specifications




Piles électriques –

Partie 2: Spécifications physiques et électriques
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.220.10 ISBN 978-2-8322-2974-3



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60086-2:2016
– 2 – IEC 60086-2:2015 © IEC 2015
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions, symbols and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Symbols and abbreviations . 9
4 Battery dimensions, symbols . 10
5 Constitution of the battery specification tables . 10
6 Physical and electrical specifications . 12
6.1 Category 1 batteries . 12
6.1.1 General . 12
6.1.2 Category 1 – Specifications: LR20, R20P, R20S . 13
6.1.3 Category 1 – Specifications: LR14, R14P, R14S . 14
6.1.4 Category 1 – Specifications: LR6, FR14505, R6P, R6S . 15
6.1.5 Category 1 – Specifications: LR03, FR10G445, R03 . 16
6.1.6 Category 1 – Specifications: LR1, R1, LR8D425 . 17
6.2 Category 2 batteries – Specifications: CR14250, CR15H270, CR17345,
CR17450, BR17335 . 18
6.3 Category 3 batteries – Specifications: LR9, CR11108 . 19
6.4 Category 4 batteries . 20
6.4.1 General . 20
6.4.2 Category 4 – Specifications: PR70, PR41, PR48, PR44 . 20
6.4.3 Fit acceptance gauge for PR batteries . 22
6.4.4 Category 4 – Specifications: LR41, LR55, LR54, LR43, LR44 . 23
6.4.5 Category 4 – Specifications: SR62, SR63, SR65, SR64, SR60, SR67,
SR66, SR58, SR68, SR59, SR69, SR41, SR57, SR55, SR48, SR54,
SR42, SR43, SR44 . 25
6.4.6 Category 4 – Specifications: CR1025, CR1216, CR1220, CR1616,
CR2012, CR1620, CR2016, CR2025, CR2320, CR2032, CR2330,
CR2430, CR2354, CR3032, CR2450, BR1225, BR2016, BR2320,
BR2325, BR3032 . 27
6.5 Category 5 batteries . 29
6.5.1 Category 5 – Specifications: 4LR44, 2CR13252, 4SR44 . 29
6.5.2 Category 5 – Specifications: 5AR40 . 30
6.6 Category 6 batteries . 31
6.6.1 Category 6 – Specifications: 3R12P, 3R12S, 3LR12 . 31
6.6.2 Category 6 – Specifications: 4LR61 . 32
6.6.3 Category 6 – Specifications: CR-P2 . 33
6.6.4 Category 6 – Specifications: 2CR5 . 34
6.6.5 Category 6 – Specifications: 4R25X, 4LR25X . 35
6.6.6 Category 6 – Specifications: 4R25Y . 36
6.6.7 Category 6 – Specifications: 4R25-2, 4LR25-2 . 37
6.6.8 Category 6 – Specifications: 6F22, 6LR61, 6LP3146 . 38
6.6.9 Category 6 – Configurations: Stud for 6F22, 6LR61 6LP3146 . 39
6.6.10 Category 6 – Specifications: 6AS4 . 40
6.6.11 Category 6 – Specifications: 6AS6 . 41

---------------------- Page: 8 ----------------------

SIST EN 60086-2:2016
IEC 60086-2:2015 © IEC 2015 – 3 –
Annex A (informative) Tabulation of batteries by application . 42
Annex B (informative) Cross-reference index . 48
Annex C (informative) Index . 51
Annex D (informative) Common designation. 52
Bibliography . 53

Figure 1 – Dimensional drawing: Category 1 . 12
Figure 2 – Dimensional drawing: LR20, R20P, R20S . 13
Figure 3 – Dimensional drawing: LR14, R14P, R14S . 14
Figure 4 – Dimensional drawing: LR6, FR14505, R6P, R6S . 15
Figure 5 – Dimensional drawing: LR03, FR10G445, R03 . 16
Figure 6 – Dimensional drawing: LR1, R1, LR8D425 . 17
Figure 7 – Dimensional drawing: CR14250, CR15H270, CR17345, CR17450, BR17335 . 18
Figure 8 – Dimensional drawing: LR9, CR11108 . 19
Figure 9 – Dimensional drawing: Category 4 . 20
Figure 10 – Dimensional drawing: PR70, PR41, PR48, PR44 . 20
Figure 11 – Gauge opening for P system batteries . 22
Figure 12 – Suggested gauge layout . 22
Figure 13 – Air hole placement diagram for P system batteries . 23
Figure 14 – Dimensional drawing: LR41, LR55, LR54, LR43, LR44 . 23
Figure 15 – Dimensional drawing: SR62, SR63, SR65, SR64, SR60, SR67, SR66,
SR58, SR68, SR59, SR69, SR41, SR57, SR55, SR48, SR54, SR42, SR43, SR44 . 25
Figure 16 – Dimensional drawing: CR1025, CR1216, CR1220, CR1616, CR2012,
CR1620, CR2016, CR2025, CR2320, CR2032, CR2330, CR2430, CR2354, CR3032,
CR2450, BR1225, BR2016, BR2320, BR2325, BR3032 . 27
Figure 17 – Dimensional drawing: 4LR44, 2CR13252, 4SR44 . 29
Figure 18 – Dimensional drawing: 5AR40. 30
Figure 19 – Dimensional drawing: 3R12P, 3R12S, 3LR12 . 31
Figure 20 – Dimensional drawing: 4LR61 . 32
Figure 21 – Dimensional drawing: CR-P2 . 33
Figure 22 – Dimensional drawing: 2CR5 . 34
Figure 23 – Dimensional drawing: 4R25X, 4LR25X . 35
Figure 24 – Dimensional drawing: 4R25Y. 36
Figure 25 – Dimensional drawing: 4R25-2, 4LR25-2 . 37
Figure 26 – Dimensional drawing: 6F22, 6LR61, 6LP3146 . 38
Figure 27 – Dimensional drawing: Stud . 39
Figure 28 – Dimensional drawing: 6AS4 . 40
Figure 29 – Dimensional drawing: 6AS6 . 41

Table 1 – Gauge opening dimension (mm) . 22
Table A.1 – Automatic camera . 42
Table A.2 – CD, digital audio, wireless gaming and accessories . 42
Table A.3 – Digital audio . 42
Table A.4 – Digital still camera . 42

---------------------- Page: 9 ----------------------

SIST EN 60086-2:2016
– 4 – IEC 60086-2:2015 © IEC 2015
Table A.5 – Electric equipment . 42
Table A.6 – Electric fence controller . 43
Table A.7 – Electronic key . 43
Table A.8 – Hearing aid . 43
Table A.9 – Hearing aid high drain . 43
Table A.10 – Hearing aid standard . 43
Table A.11 – High intensity lighting . 43
Table A.12 – Laser pointer . 44
Table A.13 – Pager . 44
Table A.14 – Photo . 44
Table A.15 – Portable lighting (LED) . 44
Table A.16 – Portable stereo . 45
Table A.17 – Radio . 45
Table A.18 – Radio / Clock . 45
Table A.19 – Radio / Clock / Remote control . 45
Table A.20 – Remote control . 45
Table A.21 – Road warning lamp . 46
Table A.22 – Smoke detector . 46
Table A.23 – Toy (motor) . 46
Table A.24 – Toy (non-motorized) . 46
Table A.25 – Wireless streaming . 47
Table B.1 – Category 1 batteries . 48
Table B.2 – Category 2 batteries . 48
Table B.3 – Category 3 batteries . 48
Table B.4 – Category 4 batteries . 49
Table B.5 – Category 5 batteries . 50
Table B.6 – Category 6 batteries . 50
Table C.1 – Index . 51
Table D.1 – Index . 52

---------------------- Page: 10 ----------------------

SIST EN 60086-2:2016
IEC 60086-2:2015 © IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

PRIMARY BATTERIES –

Part 2: Physical and electrical specifications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60086-2 has been prepared by IEC technical committee 35:
Primary cells and batteries.
This thirteenth edition cancels and replaces the twelfth edition (2011) and constitutes a
technical revision.
Significant changes from the previous edition are test changes to battery types R03, LR03, R6,
LR6, PR70, PR41, PR48, 6F22, 6LR61, 6LP3146 4LR25-2, R14, LR14, R20, LR20, CR2025,
and CR2032, adding the 5AR40 back into the standard, addition of common designations,
addition of two new battery types FR14505 and FR10G445, deletion of battery types LR53,
R40, 2EP3863, 6F100, and general editorial changes.

---------------------- Page: 11 ----------------------

SIST EN 60086-2:2016
– 6 – IEC 60086-2:2015 © IEC 2015
The text of this standard is based on the following documents:
FDIS Report on voting
35/1350/FDIS 35/1352/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60086 series, under the general title Primary batteries, can be
found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------

SIST EN 60086-2:2016
IEC 60086-2:2015 © IEC 2015 – 7 –
INTRODUCTION
The technical content of this part of IEC 60086 provides physical dimensions, discharge test
conditions and discharge performance requirements. IEC 60086-2 complements the general
information and requirements of IEC 60086-1.
This part was prepared to benefit primary battery users, device designers and battery
manufacturers by furnishing the specifics of form, fit and function for individual standardized
primary cells and batteries. Over the years, this part has been changed to improve its
contents and may again be revised in due course in the light of comments made by national
committees and experts on the basis of practical experience and changing technology.
This current revision is the result of a reformatting initiative, as well as some content changes,
aimed at making this part more user-friendly, less ambiguous, and, from a cross reference
basis, fully harmonized with other parts of IEC 60086.
NOTE Safety information is available in IEC 60086-4, IEC 60086-5 and IEC 62281.

---------------------- Page: 13 ----------------------

SIST EN 60086-2:2016
– 8 – IEC 60086-2:2015 © IEC 2015
PRIMARY BATTERIES –

Part 2: Physical and electrical specifications



1 Scope
This part of IEC 60086 is applicable to primary batteries based on standardized electro-
chemical systems.
It specifies
– the physical dimensions,
– the discharge test conditions and discharge performance requirements.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60086-1:2015, Primary batteries – Part 1: General
ISO 1101, Geometrical product specifications (GPS) – Geometrical tolerancing – Tolerances
of form, orientation, location and run-out
3 Terms, definitions, symbols and abbreviations
For the purposes of this document, the terms, definitions, symbols and abbreviations given in
IEC 60086-1 and the following apply.
3.1 Terms and definitions
3.1.1
application test
simulation of the actual use of a battery in a specific application
3.1.2
closed-circuit voltage
CCV
voltage across the terminals of a battery when it is on discharge
3.1.3
end-point voltage
EV
specified voltage of a battery at which the battery discharge is terminated
[SOURCE: IEC 60050-482:2004, 482-03-30]
3.1.4
minimum average duration
MAD
minimum average time on discharge which is met by a sample of batteries

---------------------- Page: 14 ----------------------

SIST EN 60086-2:2016
IEC 60086-2:2015 © IEC 2015 – 9 –
Note 1 to entry: The discharge test is carried out according to the specified methods or standards and designed
to show conformity with the standard applicable to the battery types.
3.1.5
nominal voltage (of a primary battery )
V
n
suitable approximate value of the voltage used to designate or identify a cell, a battery or an
electrochemical system
[SOURCE: IEC 60050-482:2004, 482-03-31, modified ("(of a primary battery)" added)]
3.1.6
open-circuit voltage
OCV
voltage across the terminals of a cell or battery when it is off discharge
3.1.7
primary (cell or battery)
cell or battery that is not designed to be electrically recharged
3.1.8
round (cell or battery)
cell or battery with circular cross section
3.1.9
service output (of a primary battery)
service life, or capacity, or energy output of a battery under specified conditions of discharge
3.1.10
service output test
test designed to measure the service output of a battery
Note 1 to entry: A service output test may be prescribed, for example, when
a) an application test is too complex to replicate;
b) the duration of an application test would make it impractical for routine testing purposes.
3.1.11
storage life
duration under specified conditions at the end of which a battery retains its ability to perform a
specified service output
[SOURCE: IEC 60050-482:2004, 482-03-47, modified ("specified function" replaced by
"specified service output”)]
3.1.12
terminals (of a primary battery)
conductive parts of a battery that provide connection to an external circuit
3.2 Symbols and abbreviations
EV end-point voltage
MAD minimum average duration
OCV open-circuit voltage (off-load voltage)
R load resistance
V nominal voltage of a primary battery
n

---------------------- Page: 15 ----------------------

SIST EN 60086-2:2016
– 10 – IEC 60086-2:2015 © IEC 2015
4 Battery dimensions, symbols
The symbols used to denote the various dimensions are as follows:
h maximum overall height of the battery;
1
h minimum dis
...