SIST EN 12573-2:2000

Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks

This standard establishes rules for the design and calculation of welded static,vertical, non-pressurised, cylindrical, flat-bottom thermoplastic tanks. This standard applies to tanks fabricated in the following thermoplastics: Polyethylene (PE), Polypropylene (PP), Poly (vinyl chloride) (PVC), Poly (vinylidene fluoride) (PVDF). This standard does not take into account wind and/or snow loading. If wind or/and snow loading has to be taken into account additional calculations are necessary.

Geschweißte orstfeste drucklose Behälter (Tanks) aus Thermoplasten - Teil 2: Berechnung von runden stehenden Behältern (Tanks)

Diese Norm legt Regeln für die Konstuktion und Berechnung von geschweißten ortsfesten drucklosen runden stehenden Flachbodentanks aus Thermoplasten fest. Diese Norm gilt für Tanks, die aus den folgenden Thermoplasten gefertigt werden: Polyethylen (PE), Polypropylen (PP), Polyvinylchlorid (PVC), Polyvinylidenfluorid (PVDF). Wind- und/oder Schneelasten werden in dieser Norm nicht berücksichtigt. Wenn Wind- und/oder Schneelasten zu berücksichtigen sind, sind zusätzliche Berechnungen notwendig.

Cuves statiques soudées en matieres thermoplastiques sans pression - Partie 2: Calcul des cuves cylindriques verticales

La présente norme fixe les regles de conception et de calcul des cuves cylindriques verticales, statiques, soudées, a fond plat, en matieres thermo- plastiques, sans pression. La présente norme s'applique aux cuves fabriquées a partir des matériaux thermoplastiques suivants: polyéthylene (PE), polypropylene(PP), polychlorure de vinyle (PVC), polyfluorure de vinylidene (PVDF). La présente norme ne tient pas compte de la charge due au vent et/ou a la neige. Si la charge due au vent et/ou la neige doit etre prise en compte, des calculs supplémentaires sont nécessaires.

Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks

General Information

• Status: Published
• Publication Date: 30-Nov-2000
• ICS: 23.020.10 - Stationary containers and tanks
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2000
• Due Date: 01-Dec-2000
• Completion Date: 01-Dec-2000
• Directive: 89/106/EEC - Construction products
• Mandate: M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
• Ref Project: EN 12573-2:2000 - Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanksGeschweißte orstfeste drucklose Behälter (Tanks) aus Thermoplasten - Teil 2: Berechnung von runden stehenden Behältern (Tanks)Cuves statiques soudées en matieres thermoplastiques sans pression - Partie 2: Calcul des cuves cylindriques verticalesWelded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks23.020.10UH]HUYRDUMLStationary
...