SIST EN ISO 15480:2001
(Main)Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999)
Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999)
Migrated from Progress Sheet (TC Comment) (2000-07-10): BP = to be published together with EN ISO 10666 (WI 00185156) (NT/1998-12-11).
Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde (ISO 15480:1999)
Diese Internationale Norm legt die Eigenschaften für Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde von ST2,9 bis ST6,3 fest.
Vis autoperceuses a tete hexagonale a ambase plate, avec filetage de vis a tôle (ISO 15480:1999)
La présente Norme internationale spécifie les caractéristiques des vis autoperceuses à tête hexagonale à embase plate, avec filetage de vis à tôle ST2,9 à ST6,3 inclus.
Pločevinski vijaki s šestrobo glavo s podglavkom in pločevinskim navojem (ISO 15480:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15480:2001
01-julij-2001
3ORþHYLQVNLYLMDNLVãHVWURERJODYRVSRGJODYNRPLQSORþHYLQVNLPQDYRMHP ,62
Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999)
Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde (ISO 15480:1999)
Vis autoperceuses a tete hexagonale a ambase plate, avec filetage de vis a tôle (ISO
15480:1999)
Ta slovenski standard je istoveten z: EN ISO 15480:1999
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 15480:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15480:2001
---------------------- Page: 2 ----------------------
SIST EN ISO 15480:2001
---------------------- Page: 3 ----------------------
SIST EN ISO 15480:2001
---------------------- Page: 4 ----------------------
SIST EN ISO 15480:2001
---------------------- Page: 5 ----------------------
SIST EN ISO 15480:2001
---------------------- Page: 6 ----------------------
SIST EN ISO 15480:2001
INTERNATIONAL ISO
STANDARD 15480
First edition
1999-09-01
Hexagon washer head drilling screws
with tapping screw thread
Vis autoperceuses à tête hexagonale à embase plate, avec filetage de vis
à tôle
A
Reference number
ISO 15480:1999(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 15480:2001
ISO 15480:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 15480 was prepared by Technical Committee ISO/TC 2, Fasteners.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 15480:2001
INTERNATIONAL STANDARD © ISO ISO 15480:1999(E)
Hexagon washer head drilling screws with tapping screw
thread
1 Scope
This International Standard specifies the characteristics of hexagon washer head drilling screws with tapping screw
threads from ST2,9 up to and including ST6,3.
Normative references
2
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.