SIST EN 303 372-2 V1.1.1:2016
(Main)Satellite Earth Stations and Systems (SES) - Satellite broadcast reception equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 2: Indoor unit
Satellite Earth Stations and Systems (SES) - Satellite broadcast reception equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 2: Indoor unit
The present document applies to indoor units (IDUs) for satellite broadcast reception. An indoor unit gets on an input
interface the signal that has been received from satellite and processed by the outdoor unit (ODU). It performs carrier
selection, demodulation, audio and video decoding.
Part of the IDU functionality may be integrated with the ODU. In that case the present document applies to this part of
functionality as well as the remaining part in the IDU.
The indoor unit may be integrated with a domestic television receiver.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
Satelitske zemeljske postaje in sistemi (SES) - Oprema za sprejemanje satelitske radiodifuzije - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU - 2. del: Notranja enota
Ta dokument se uporablja za notranje enote (IDU) za sprejemanje satelitske radiodifuzije. Notranja enota dobi prek vhodnega vmesnika signal, ki je bil sprejet iz satelita in ga je obdelala zunanja enota (ODU). Izvede izbiro nosilca, demodulacijo ter avdio in video dekodiranje.
Del funkcionalnosti notranje enote se lahko vključi v zunanjo enoto. V tem primeru se ta dokument uporablja za takšen del funkcionalnosti, kot tudi za preostali del v notranji enoti.
Notranja enota se lahko vključi v televizijski sprejemnik za domačo uporabo. Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja in tudi podpira
učinkovito uporabo radijskega spektra, tako da ne pride do škodljivih motenj.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 303 372-2 V1.1.1 (2016-04)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Satellite broadcast reception equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 2: Indoor unit
---------------------- Page: 1 ----------------------
2 ETSI EN 303 372-2 V1.1.1 (2016-04)
Reference
DEN/SES-00376-2
Keywords
broadcasting, receiver, requirements, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 372-2 V1.1.1 (2016-04)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Symbols and abbreviations . 6
3.1 Symbols . 6
3.2 Abbreviations . 6
4 Technical requirements specifications . 6
4.1 Environmental profile . 6
4.2 Equipment capabilities . 6
4.3 Conformance requirements . 6
4.3.1 Adjacent signal selectivity . 6
4.3.2 Dynamic range . 7
5 Testing for compliance with technical requirements . 7
5.1 Environmental conditions for testing . 7
5.2 Interpretation of the measurement results . 8
6 Test methods . 8
6.1 Adjacent signal selectivity . 8
6.2 Dynamic range . 8
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 9
Annex B (informative): Interface between ODU and IDU . 10
Annex C (informative): Applicability in conjunction with CENELEC EN 50585:2014 . 11
Annex D (informative): Applicability of parameters given in ETSI EG 203 336 . 12
Annex E (informative): Other IDU features and performance characteristics . 13
History . 14
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 372-2 V1.1.1 (2016-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations
and Systems (SES).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in ETSI
EN 303 372-1 [i.1].
National transposition dates
Date of adoption of this EN: 13 April 2016
Date of latest announcement of this EN (doa): 31 July 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2017
Date of withdrawal of any conflicting National Standard (dow): 31 January 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
See ETSI EN 303 372-1 [i.1].
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 372-2 V1.1.1 (2016-04)
1 Scope
The present document applies to indoor units (IDUs) for satellite broadcast reception. An indoor unit gets on an input
interface the signal that has been received from satellite and processed by the outdoor unit (ODU). It performs carrier
selection, demodulation, audio and video decoding.
Part of the IDU functionality may be integrated with the ODU. In that case the present document applies to this part of
functionality as well as the remaining part in the IDU.
The indoor unit may be integrated with a domestic television receiver.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 303 372-1: "Satellite Earth Stations and Systems (SES); Satellite broadcast reception
equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive
2014/53/EU; Part-1: Outdoor unit receiving in the 10,7 GHz to 12,75 GHz frequency band".
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] ETSI EG 203 336 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Guide for the selection of technical parameters for the production of Harmonised Standards
covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.4] CENELEC EN 50585:2014: "Communications protocol to transport satellite delivered signals over
IP networks".
[i.5] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 372-2 V1.1.1 (2016-04)
3 Symbols and abbreviations
3.1 Symbols
For the purposes of the present document, the following symbols apply:
F ideal signal occupied bandwidth
R symbol rate
s
α roll-off
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
EIRP Equivalent Isotropically Radiated Power
IDU InDoor Unit
ODU OutDoor Unit
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Satellite Earth Stations and Systems (SES) - Satellite broadcast reception equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 2: Indoor unit33.170Televizijska in radijska difuzijaTelevision and radio broadcasting33.070.40SatelitSatelliteICS:Ta slovenski standard je istoveten z:ETSI EN 303 372-2 V1.1.1 (2016-04)SIST EN 303 372-2 V1.1.1:2016en01-julij-2016SIST EN 303 372-2 V1.1.1:2016SLOVENSKI
STANDARD
SIST EN 303 372-2 V1.1.1:2016
ETSI EN 303 372-2 V1.1.1 (2016-04) Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: Indoor unit
HARMONISED EUROPEAN STANDARD SIST EN 303 372-2 V1.1.1:2016
ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 2
Reference DEN/SES-00376-2 Keywords broadcasting, receiver, requirements, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 372-2 V1.1.1:2016
ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Modal verbs terminology . 4 Introduction . 4 1 Scope . 5 2 References . 5 2.1 Normative references . 5 2.2 Informative references . 5 3 Symbols and abbreviations . 6 3.1 Symbols . 6 3.2 Abbreviations . 6 4 Technical requirements specifications . 6 4.1 Environmental profile . 6 4.2 Equipment capabilities . 6 4.3 Conformance requirements . 6 4.3.1 Adjacent signal selectivity . 6 4.3.2 Dynamic range . 7 5 Testing for compliance with technical requirements . 7 5.1 Environmental conditions for testing . 7 5.2 Interpretation of the measurement results . 8 6 Test methods . 8 6.1 Adjacent signal selectivity . 8 6.2 Dynamic range . 8 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 9 Annex B (informative): Interface between ODU and IDU . 10 Annex C (informative): Applicability in conjunction with CENELEC EN 50585:2014 . 11 Annex D (informative): Applicability of parameters given in ETSI EG 203 336 . 12 Annex E (informative): Other IDU features and performance characteristics . 13 History . 14
SIST EN 303 372-2 V1.1.1:2016
ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.2]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in ETSI EN 303 372-1 [i.1].
National transposition dates Date of adoption of this EN: 13 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 January 2017 Date of withdrawal of any conflicting National Standard (dow): 31 January 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction See ETSI EN 303 372-1 [i.1].
SIST EN 303 372-2 V1.1.1:2016
ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 5 1 Scope The present document applies to indoor units (IDUs) for satellite broadcast reception. An indoor unit gets on an input interface the signal that has been received from satellite and processed by the outdoor unit (ODU). It performs carrier selection, demodulation, audio and video decoding.
Part of the IDU functionality may be integrated with the ODU. In that case the present document applies to this part of functionality as well as the remaining part in the IDU. The indoor unit may be integrated with a domestic television receiver. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI EN 303 372-1: "Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part-1: Outdoor unit receiving in the 10,7 GHz to 12,75 GHz frequency band". [i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.3] ETSI EG 203 336 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU". [i.4] CENELEC EN 50585:2014: "Communications protocol to transport satellite delivered signals over IP networks". [i.5] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. SIST EN 303 372-2 V1.1.1:2016
ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 6 3 Symbols and abbreviations 3.1 Symbols For the purposes of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.