SIST EN IEC 60684-3-283:2019

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation (IEC 60684-3-283:2019)

This document gives the requirements for two types of heat-shrinkable, polyolefin sleeving for bus-bar insulation, with a nominal shrink ratio of 2,5:1. This sleeving has been found suitable up to temperatures of 100 °C. • Type A: Medium wall - internal diameter up to 170,0 mm typically • Type B: Thick wall - internal diameter up to 165,0 mm typically These sleevings are normally supplied in colour, red or brown. Since these types of sleeving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) provides guidance to the range of sizes available.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283: Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen (IEC 60684-3-283:2019)

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 283: Gaines thermorétractables, en polyoléfine pour isolation de barre omnibus (IEC 60684-3-283:2019)

IEC 60684-3-283:2019 est disponible sous forme de IEC 60684-3-283:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

IEC 60684-3-283:2019 donne les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, pour isolation des barres omnibus dont le rapport de rétreint nominal est 2,5:1. Ces gaines se sont avérées appropriées pour une utilisation à des températures allant jusqu’à 100 °C.
Type A: Paroi moyenne - diamètre intérieur généralement jusqu’à 170,0 mm
Type B: Paroi épaisse - diamètre intérieur généralement jusqu’à 165,0 mm
Ces gaines sont normalement disponibles en rouge ou en brun. Comme ces types de gaines couvrent une plage très étendue de tailles et d’épaisseurs de paroi, l'Annexe A (Tableaux A.1 et A.2) fournit un guide des tailles disponibles dans cette plage. La taille réelle et l'épaisseur de la paroi font l’objet d’un accord entre l’utilisateur et le fournisseur en fonction de la rigidité diélectrique du tube installé et des exigences de l’utilisateur. Les matériaux conformes à la présente spécification satisfont à des niveaux de performances établis. Cependant, le choix d’un matériau par un utilisateur, pour une application spécifique, est fondé sur les exigences réelles nécessaires pour obtenir des performances adéquates pour l'application concernée, et n'est pas fondé sur cette seule spécification. Cette deuxième édition annule et remplace la première édition parue en 2010 et l'Amendement 1:2013. Cette édition constitue une révision technique. Cette édition inclut la modification technique majeure suivante par rapport à l'édition précédente:
- modification de l'épaisseur des plaques moulées pour les essais de résistance aux courants de cheminement et les essais de résistance aux intempéries qui devient (6 ± 0,5) mm.
Mots-clés : Gaines thermorétractables en polyoléfine pour isolation de barre omnibus

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 283. list: Toplotno skrčljive poliolefinske cevi za izolacijo zbiralk (IEC 60684-3-283:2019)

Ta dokument podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi za izolacijo zbiralk z nazivnimi razmerji krčenja do 2,5:1. Te cevi so primerne za temperature do 100 °C.
• Tip A: srednje debela stena – notranji premer običajno do 170,0 mm.
• Tip B: debela stena – notranji premer običajno do 165,0 mm. Te cevi so običajno dobavljive v rdeči ali rjavi barvi. Ker ta tipa cevi zajemata bistveno velik razpon velikosti in debelin sten, so v preglednicah A.1 in A.2 v dodatku A podane smernice glede razpona razpoložljivih velikosti.

General Information

• Status: Published
• Publication Date: 04-Nov-2019
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 23-Oct-2019
• Due Date: 28-Dec-2019
• Completion Date: 05-Nov-2019
• Ref Project: EN IEC 60684-3-283:2019 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation

Relations

• Revised: SIST EN 60684-3-283:2011 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation (IEC 60684-3-283:2010)
• Effective Date: 21-Aug-2018
• Replaces: SIST EN 60684-3-283:2011 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation (IEC 60684-3-283:2010)
• Effective Date: 22-Oct-2019
• Replaces: SIST EN 60684-3-283:2011/A1:2014 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
• Effective Date: 22-Oct-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60684-3-283:2019
01-december-2019
Nadomešča:
SIST EN 60684-3-283:2011
SIST EN 60684-3-283:2011/A1:2014
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 283. list:
Toplotno skrčljive poliolefinske cevi za izolacijo zbiralk (IEC 60684-3-283:2019)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation (IEC 60684-3-283:2019)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283:
Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen (IEC 60684
-3-283:2019)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 283: Gaines thermorétractables, en polyoléfine pour isolation de barre omnibus
(IEC 60684-3-283:2019)
Ta slovenski standard je istoveten z: EN IEC 60684-3-283:2019
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
SIST EN IEC 60684-3-283:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60684-3-283:2019

---------------------- Page: 2 ----------------------
SIST EN IEC 60684-3-283:2019


EUROPEAN STANDARD EN IEC 60684-3-283

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2019
ICS 29.035.20 Supersedes EN 60684-3-283:2011 and all of its
amendments and corrigenda (if any)
English Version
Flexible insulating sleeving - Part 3: Specifications for individual
types of sleeving - Sheet 283: Heat-shrinkable, polyolefin
sleeving for bus-bar insulation
(IEC 60684-3-283:2019)
Gaines isolantes souples - Partie 3: Spécifications pour Isolierschläuche - Teil 3: Anforderungen für einzelne
types particuliers de gaines - Feuille 283: Gaines Schlauchtypen - Blatt 283: Polyolefin-
thermorétractables, en polyoléfine pour isolation de barres Wärmeschrumpfschläuche für die Isolierung von
omnibus Sammelschienen
(IEC 60684-3-283:2019) (IEC 60684-3-283:2019)
This European Standard was approved by CENELEC on 2019-09-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60684-3-283:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60684-3-283:2019
EN IEC 60684-3-283:2019 (E)
European foreword
The text of document 15/892/FDIS, future edition 2 of IEC 60684-3-283, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60684-3-283:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-24
document have to be withdrawn

This document supersedes EN 60684-3-283:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60684-3-283:2019 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60684-3 (series) NOTE Harmonized as EN 60684-3-420 to 422 (series)

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60684-3-283:2019
EN IEC 60684-3-283:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60296 2012 Fluids for electrotechnical applications - Unused EN 60296 2012
mineral insulating oils for transformers and
switchgear
IEC 60684-1 2003 Flexible insulating sleeving - Part 1: Definitions EN 60684-1 2003
and general requirements
IEC 60684-2 2011 Flexible insulating sleeving - Part 2: Methods of EN 60684-2 2011
test
IEC 60757 1983 Code for designation of colours HD 457 S1 1985
ISO 846 2019 Plastics - Evaluation of the action of micro- EN ISO 846 2019
organisms
ISO 4892-3 2016 Plastics - Methods of exposure to laboratory light EN ISO 4892-3 2016
sources - Part 3: Fluorescent UV lamps

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60684-3-283:2019

---------------------- Page: 6 ----------------------
SIST EN IEC 60684-3-283:2019



IEC 60684-3-283

®


Edition 2.0 2019-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Flexible insulating sleeving –

Part 3: Specifications for individual types of sleeving –

Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation




Gaines isolantes souples –

Partie 3: Spécifications pour types particuliers de gaines –


Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barres

omnibus












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.035.20 ISBN 978-2-8322-7215-2




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60684-3-283:2019
– 2 – IEC 60684-3-283:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designation . 7
5 Conditions of test . 7
6 Requirements . 7
7 Sleeving conformance . 7
Annex A (informative) Guidance to the available sizes and wall thicknesses . 12
Bibliography . 13

Table 1 – Property requirements . 8
Table 2 – Requirements for dielectric strength . 10
Table 3 – Resistance to selected fluids . 10
Table 4 – Additional property requirements . 11
Table A.1 – Type A, medium wall . 12
Table A.2 – Type B, thick wall . 12

---------------------- Page: 8 ----------------------
SIST EN IEC 60684-3-283:2019
IEC 60684-3-283:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use
...