SIST EN 9300-120:2024

Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data - Part 120: CAD 3D explicit geometry with graphic product and manufacturing information

1.1 Introduction
This document defines the requirements for the long term digital preservation of the presentation of Product and Manufacturing Information (PMI) with their possible links to the 3D explicit shape and geometry of single CAD parts. The goal is to preserve this 3D information with respect to the geometry and related PMI produced by the original CAD system, following the principles laid down in EN 9300 003 “Fundamentals and Concepts”.
The requirements of EN 9300 110 “CAD mechanical 3D explicit geometry information” about the preservation of the 3D explicit shape shall apply within this document.
The meaning of terms "Presentation" and "Representation", defined in the EN 9300 100 “Common concepts for Long term archiving and retrieval of CAD 3D mechanical information” is required to understand this EN 9300 document.
1.2 In scope
The following outlines the total scope of this document:
- the Presentation of 3D geometrical dimension and tolerance, and 3D annotation attributes;
- their possible semantic links with 3D Geometric shape;
- User Defined Attributes: that are assigned to 3D geometric entities or at the part level.
For the purpose of this document, the semantic definition is at the level that supports associative “Cross-highlighting”, to illustrate the portion of the geometry to which a PMI element applies.
In this version, the technology used to preserve this 3D information is based on polyline and tessellated presentation. Polyline presentation is a conversion to lines and curves of all 3D annotations by the STEP interfaces of the CAD system, including validation properties.  Tessellated presentation is a conversion to tessellated curves and tessellated faces. The main use cases are the Certification and Product Liability of static information, however, re-use is also possible after the deletion of previous PMI and creation of new PMI (refer to clause 3 for definition).
1.3 Out of scope
The following is outside the scope:
- machine-interpretable PMI “Representation”;
- how to preserve additional information:
- - property rights;
- -form features;
- -machining features;
- CAD Assemblies.

Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und -Bereitstellung digitaler technischer Produktdokumentationen, wie zum Beispiel von 3D-, CAD- und PDM-Daten - Teil 120: Eindeutige 3D-CAD-Geometrie mit grafischen Produkt- und Fertigungsinformationen

Série aérospatiale - LOTAR - Archivage long terme et récupération des données techniques produits numériques, telles que CAO 3D et PDM - Partie 120 : Géométrie CAO 3D explicite avec données graphiques de produit et de fabrication

Aeronavtika - LOTAR - Dolgotrajno arhiviranje in iskanje digitalne tehnične dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 120. del: CAD 3D eksplicitne informacije o geometriji z grafičnim izdelkom in izdelavo

1.1 Uvod
Ta dokument določa zahteve za dolgoročno digitalno shranjevanje predstavitve informacij o grafičnem izdelku in proizvodnji (PMI) z morebitnimi povezavami do 3D eksplicitne oblike in geometrije posameznih delov CAD. Cilj je ohraniti 3D informacije glede na geometrijo ter povezane informacije o grafičnem izdelku in proizvodnji, ki jih proizvede prvotni sistem CAD, v skladu z načeli, določenimi v standardu EN 9300-003 »Osnove in pojmi«.
V tem dokumentu je treba upoštevati zahteve standarda EN 9300-110 »CAD mehanske 3D eksplicitne informacije o geometriji« v zvezi s shranjevanjem 3D eksplicitne oblike.
Za razumevanje tega dokumenta EN 9300 je potreben pomen izrazov »predstavitev« in »prikaz«, opredeljenih v standardu EN 9300-100 »Splošni pojmi za dolgoročno arhiviranje in pridobivanje CAD 3D mehanskih informacij«.
1.2 Znotraj področja uporabe
Naslednje opisuje celotno področje uporabe tega dokumenta:
– predstavitev 3D geometrijskih dimenzij in toleranc ter 3D atributov opomb;
– njihove morebitne semantične povezave s 3D geometrijsko obliko;
– uporabniško določeni atributi, ki so dodeljeni 3D geometrijskim entitetam ali na ravni dela.
Za namene tega dokumenta je semantična definicija na ravni, ki podpira asociativno »navzkrižno poudarjanje« za ponazoritev dela geometrije, za katerega se uporablja element informacij o grafičnem izdelku in proizvodnji.
V tej različici tehnologija, ki se uporablja za shranjevanje 3D informacij, temelji na lomljeni in mozaični predstavitvi. Lomljena predstavitev je pretvorba v črte in krivulje vseh 3D opomb prek vmesnikov STEP sistema CAD, vključno s potrjevalnimi lastnostmi.  Mozaična predstavitev je pretvorba v mozaične krivulje in mozaične ploščice. Glavna primera uporabe sta certificiranje in odgovornost za izdelek v okviru statičnih informacij, vendar je možna tudi vnovična uporaba po izbrisu prejšnjih oziroma ustvarjanju novih informacij o grafičnem izdelku in proizvodnji (za definicijo glej točko 3).
1.3 Zunaj področja uporabe
Naslednje ne spada na področje uporabe:
– »prikaz« strojno berljivih informacij o grafičnem izdelku in proizvodnji;
– način shranjevanja dodatnih informacij;
– lastninske pravice;
– oblikovne lastnosti;
– lastnosti strojne obdelave;
– sestavi CAD.

General Information

• Status: Published
• Public Enquiry End Date: 14-Sep-2022
• Publication Date: 19-Nov-2023
• ICS: 01.110 - Technical product documentation
• ICS: 35.240.30 - IT applications in information, documentation and publishing
• ICS: 49.020 - Aircraft and space vehicles in general
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 16-Nov-2023
• Due Date: 21-Jan-2024
• Completion Date: 20-Nov-2023
• Ref Project: EN 9300-120:2023 - Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data - Part 120: CAD 3D explicit geometry with graphic product and manufacturing information

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 9300-120:2024
01-januar-2024
Aeronavtika - LOTAR - Dolgotrajno arhiviranje in iskanje digitalne tehnične
dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 120. del: CAD 3D
eksplicitne informacije o geometriji z grafičnim izdelkom in izdelavo
Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical
product documentation such as 3D CAD and PDM data - Part 120: CAD 3D explicit
geometry with graphic product and manufacturing information
Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und -Bereitstellung digitaler
technischer Produktdokumentationen, wie zum Beispiel von 3D-, CAD- und PDM-Daten -
Teil 120: Eindeutige 3D-CAD-Geometrie mit grafischen Produkt- und
Fertigungsinformationen
Série aérospatiale - LOTAR - Archivage long terme et récupération des données
techniques produits numériques, telles que CAO 3D et PDM - Partie 120 : Géométrie
CAO 3D explicite avec données graphiques de produit et de fabrication
Ta slovenski standard je istoveten z: EN 9300-120:2023
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
35.240.30 Uporabniške rešitve IT v IT applications in information,
informatiki, dokumentiranju in documentation and
založništvu publishing
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
SIST EN 9300-120:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 9300-120:2024

---------------------- Page: 2 ----------------------
SIST EN 9300-120:2024


EN 9300-120
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2023
EUROPÄISCHE NORM
ICS 01.110
English Version

Aerospace series - LOTAR - LOng Term Archiving and
Retrieval of digital technical product documentation such
as 3D CAD and PDM data - Part 120: CAD 3D explicit
geometry with graphic product and manufacturing
information
Série aérospatiale - LOTAR - Archivage long terme et Série aérospatiale - LOTAR - Archivage long terme et
récupération des données techniques produits récupération des données techniques produits
numériques, telles que CAD 3D et PDM - Partie 120: numériques telles que CAO, 3D et PDM - Partie 120 :
CAO 3D explicite et informations graphiques 3D pour Géométrie CAO 3D explicite avec données graphiques
la fabrication du produit de produit et de fabrication
This European Standard was approved by CEN on 22 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 9300-120:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 9300-120:2024
EN 9300-120:2023 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
1.1 In scope . 6
1.2 Out of scope . 6
2 Normative references .
...

SLOVENSKI STANDARD
oSIST prEN 9300-120:2022
01-september-2022
Aeronavtika - LOTAR - Dolgotrajno arhiviranje in iskanje digitalne tehnične
dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 120. del: CAD 3D
eksplicitne informacije o geometriji z grafičnim izdelkom in izdelavo
Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical
product documentation such as 3D CAD and PDM data - Part 120: CAD 3D explicit
geometry with graphic product and manufacturing information
Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und -Bereitstellung digitaler
technischer Produktdokumentationen, wie zum Beispiel von 3D-, CAD- und PDM-Daten -
Teil 120: Eindeutige 3D-CAD-Geometrie mit grafischen Produkt- und
Fertigungsinformationen
Série aérospatiale - LOTAR - Archivage long terme et récupération des données
techniques produits numériques, telles que CAO 3D et PDM - Partie 120 : Géométrie
CAO 3D explicite avec données graphiques de produit et de fabrication
Ta slovenski standard je istoveten z: prEN 9300-120
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
35.240.30 Uporabniške rešitve IT v IT applications in information,
informatiki, dokumentiranju in documentation and
založništvu publishing
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
oSIST prEN 9300-120:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 9300-120:2022

---------------------- Page: 2 ----------------------
oSIST prEN 9300-120:2022


DRAFT
EUROPEAN STANDARD
prEN 9300-120
NORME EUROPÉENNE

EUROPÄISCHE NORM

June 2022
ICS 01.110
English Version

Aerospace series - LOTAR - LOng Term Archiving and
Retrieval of digital technical product documentation such
as 3D CAD and PDM data - Part 120: CAD 3D explicit
geometry with graphic product and manufacturing
information
Série aérospatiale - LOTAR - Archivage long terme et Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung
récupération des données techniques produits und -Bereitstellung digitaler technischer
numériques, telles que CAO 3D et PDM - Partie 120 : Produktdokumentationen, wie zum Beispiel von 3D-,
Géométrie CAO 3D explicite avec données graphiques CAD- und PDM-Daten - Teil 120: Eindeutige 3D-CAD-
de produit et de fabrication Geometrie mit grafischen Produkt- und
Fertigungsinformationen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 9300-120:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 9300-120:2022
FprEN 9300-120:2022 (E)
Contents Page

European foreword . 3
1 Scope . 4
1.1 Introduction . 4
1.2 In scope .
...