SIST EN 60406:1998
(Main)Cassettes for medical X-ray diagnosis - Radiographic cassettes and mammographic cassettes
Cassettes for medical X-ray diagnosis - Radiographic cassettes and mammographic cassettes
Deals with the manufacture of radiographic cassettes and mammographic cassettes intended to be used with radiographic screens in medical practice.
Kassetten für medizinische Röntgenaufnahmen - Röntgenkassetten und Mammographie-Kassetten
Cassettes pour la radiographie médicale - Cassettes radiographiques et cassettes mammographiques
Concerne la fabrication de cassettes radiographiques et de cassettes mammographiques destinées à être utilisées avec des écrans radiographiques dans la pratique médicale.
Cassettes for medical X-ray diagnosis - Radiographic cassettes and mammographic cassettes (IEC 60406:1997)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-1998
Cassettes for medical X-ray diagnosis - Radiographic cassettes and
mammographic cassettes (IEC 60406:1997)
Cassettes for medical X-ray diagnosis - Radiographic cassettes and mammographic
cassettes
Kassetten für medizinische Röntgenaufnahmen - Röntgenkassetten und Mammographie
-Kassetten
Cassettes pour la radiographie médicale - Cassettes radiographiques et cassettes
mammographiques
Ta slovenski standard je istoveten z: EN 60406:1997
ICS:
11.040.50 Radiografska oprema Radiographic equipment
37.040.99 Drugi standardi v zvezi s Other standards related to
fotografijo photography
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
...
This May Also Interest You
IEC 63522-48:2024 is used for for testing electromechanical elementary relays (electromechanical relays, reed relays, reed contacts, reed switches and technology combinations of these) and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for contact failure rate test of electromechanical elementary relays applied to low-load applications (e.g., CC 0, CC 1) and failure rates and failure rate levels at low loads under specified conditions.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
- 20-Mar-2025
- 29.120.70
- ISS EIT.ERE
IEC 63522-13:2024 is used for testing electromechanical elementary relays (electromechanical relays, reed relays, reed contacts, reed switches and technology combinations of these) and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method to simulate impacts of sulfuric atmospheres to relays. The test conditions simulate an artificial situation and allow a performance comparison for usability of the devices under test (DUT) with regard to known and existing switching solutions.
The test is a static test without actual operation of the DUT to simulate a worst-case scenario for corrosion, since corrosion increases over time. The corrosion layer can potentially create contact sticking, increase resistance or other undesired effects in the relay. Those aspects can be affected by DUT actuations during the test, which can destroy the corrosion layers or hide relevant long-term effects.
In addition to polluted atmospheres, the suitability of the DUT for use and/or storage in corrosive atmospheres can be assessed in a salt-laden atmosphere as described in IEC 63522-44.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
- 31-Oct-2023
- 20-Mar-2025
- 29.120.70
- ISS EIT.ERE
IEC 63522-15:2024 is used for testing electromechanical elementary relays (electromechanical relays, reed relays, reed contacts, reed switches and technology combination of these) and evaluates their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method that applies defined loads to relay terminals (direct axial pulls, bending or twisting) as they can be present in assembled configurations or during handling. In addition, it covers torque stress for nuts and threaded terminals as they are likely to be experienced during normal assembly operations.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
- 31-Oct-2023
- 20-Mar-2025
- 29.120.70
- ISS EIT.ERE
IEC 63522-17:2024 is used for testing electromechanical elementary relays (electromechanical relays, reed relays, reed contacts, reed switches and technology combination of these) and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method to simulate the mechanical stress on relays as it can occur in service, during handling or during transportation. This document comprises test procedures to simulate shock impacts, steady acceleration environments (such as moving vehicles, aircraft and projectiles) as well as vibration conditions.
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
- 31-Oct-2023
- 20-Mar-2025
- 29.120.70
- ISS EIT.ERE
1.1 This document specifies the safety requirements and measures for manually loaded and unloaded
— single-end tenoning machines with a manual feed sliding table,
— single-end tenoning machines with a mechanical feed sliding table,
— single-end tenoning-profiling machines with mechanical feed,
— double-end tenoning-profiling machines with mechanical feed, also designed to be automatically either
loaded or unloaded, or both, and
— angular systems for tenoning and profiling with mechanical feed
with maximum workpiece height capacity of 200 mm for single-end machines and 500 mm for double-end
machines, capable of continuous production use, altogether referred to as “machines”.
1.2 This document deals with all significant hazards, hazardous situations and events as listed in Annex A,
relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen
by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling,
disabling and scrapping phases have been taken into account.
1.3 The machines are designed to process in one pass one end or two sides, either opposite or perpendicular
to each other, of workpieces made of
a) solid wood, and
b) materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2); and
only the machines with mechanical feed, made of
c) fibre-cement,
d) rock wool and glass wool,
e) gypsum,
f) plasterboard,
g) matrix engineered mineral boards, silicate boards and sulfate boards,
h) composite materials with core consisting of polyurethane or mineral material laminated with light alloy,
i) polymer-matrix composite materials and reinforced thermoplastic, thermoset and elastomeric
materials,
j) aluminium light alloy profiles, and
k) composite boards made from the materials listed above.
1.4 This document is also applicable to machines fitted with one or more of the following devices or
additional working units, whose hazards have been dealt with:
— sanding units;
— fixed or movable workpiece support;
— automatic tool changing;
— automatic workpiece returner;
— glass bead saw unit;
— hinge recessing unit;
— boring unit;
— dynamic processing unit;
— sawing unit installed out of the integral enclosure, between machine halves in double-end machines;
— foiling unit;
— coating unit;
— grooving unit with a milling tool installed out of the integral enclosure, between machine halves;
— brushing unit;
— gluing unit;
— sealing unit;
— dowels inserting unit;
— tongues inserting unit;
— inkjet marking unit;
— laser marking unit;
— labelling unit;
— workpiece back-up device (device that is either anti-chipping or anti-splintering, or both);
— quick tool changing system;
— post-formed edge pre-cutting unit;
— additional workpiece support (at either infeed or outfeed, or both);
— parallel infeed device on single-end machines;
— transversal infeed device on single-end machines;
— intermediate workpiece support on double-end machines;
— automatic infeed device;
— feed chain with dogs.
1.5 This document does not deal with any hazards related to:
a) systems for automatic loading and unloading of the workpiece to a single machine other than automatic
workpiece returner;
b) single machine being used in combination with any other machine (as part of a line);
c) use of tools, other than saw blades or boring tools or milling tools for grooving, installed between
machine halves and out of the integral enclosure in double-end machines;
d) use of tools protruding out of the integral enclosure;
e) chemical characteristics of all materials listed in 1.3 c) to i) and their dust.
1.6 This document is not applicable to machines intended for use in potentially explosive atmosphere nor
to machines manufactured prior to its publication.
- Standard76 pagesEnglish languagesale 10% offe-Library read for×1 day
- 27-Feb-2023
- 17-Mar-2025
- 13.110
- 79.120.10
- 2006/42/EC
- M/396
- VSN
This document specifies requirements and measures for removal or reduction of hazards resulting from the design and application of power-driven brushes.
NOTE Power-driven brushing tools are e.g. cup brushes, wheel brushes, end brushes, disc brushes, tube brushes and head brushes.
This document also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
This document does not apply to cylinder brushes and strip brushes, brushes for car washing, vacuum cleaners, floor cleaning, drain and street cleaning machines and dental brushes.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the main characteristics of the voltage at a network user's supply terminals in public low voltage, medium, high, and extra-high voltage AC electricity networks under normal operating conditions. This document specifies the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public European electricity networks, only. Industrial networks are excluded from the scope of EN 50160. NOTE 1 If non-public networks (e.g. residential quarters, energy communities, office centres, shopping centres) have similar end-users as public networks, it is strongly advised to apply the same requirements as for public networks. This document does not apply under abnormal operating conditions, including the following: a) a temporary supply arrangement to keep network users supplied during conditions arising as a result of a fault, maintenance and construction work, or to minimize the extent and duration of a loss of supply; b) in the case of non-compliance of a network user's installation or equipment with the relevant standards or with the technical requirements for connection, established either by the public authorities or the network operator, including the limits for the emission of conducted disturbances; NOTE 2 A network user’s installation can include load and generation. c) in exceptional situations, in particular: 1) exceptional weather conditions and other natural disasters; 2) third party interference; 3) acts by public authorities, 4) industrial actions (subject to legal requirements); 5) force majeure; 6) power shortages resulting from external events. The voltage characteristics given in this document refer to conducted disturbances in public electric power networks. They are not intended to be used as electromagnetic compatibility (EMC) levels or product emission limits. Power quality is related to EMC in several ways – especially because compliance with power quality requirements depends on the control of cumulative effect of electromagnetic emissions from all/multiple equipment and/or installations. Therefore, the voltage characteristics given in this document gives guidance for specifying requirements in equipment product standards and in installation standards. NOTE 3 The performance of equipment might be impaired if it is subjected to supply conditions which are not specified in the equipment product standard. NOTE 4 This document can be superseded in total or in part by the terms of a contract between the individual network user and the network operator. The sharing of complaint management and problem mitigation costs between the involved parties is outside the scope of EN 50160.
- Amendment7 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements for the positioning and dimensioning of safeguards with respect
to the approach of the human body or its parts towards hazard(s) within the intended span-of-control as
follows:
— the position and dimension of the detection zone(s) of ESPE and pressure-sensitive mats and pressuresensitive
floors;
— the position of two-hand control devices and single control devices;
— the position of interlocking guards.
This document also specifies requirements for the positioning of safety-related manual control devices
(SRMCD) with respect to the approach of the human body or its parts from within the safeguard space
relative to:
— the position and dimension of the detection zone(s) of ESPE and pressure-sensitive mats and pressuresensitive
floors; and
— the position and dimension of interlocking guards.
When evaluating the ability of the human body or its parts to access SRMCD from within the intended
safeguarded space, the requirements of this document are also applicable to determine the dimensions of
safeguard(s). Approaches such as running, jumping or falling, are not considered in this document.
NOTE 1 The values for approach speeds (walking speed and upper limb movement) in this document are time
tested and proven in practical experience.
NOTE 2 Other types of approach can result in approach speeds that are higher or lower than those defined in this
document.
This document applies to safeguards used on machinery for the protection of persons 14 years and older.
Safeguards considered in this document include:
a) electro-sensitive protective equipment (ESPE) such as:
— active opto-electronic protective devices (AOPDs) (see IEC 61496-2);
— AOPDs responsive to diffuse reflection that have one or more detection zone(s) specified in two
dimensions (AOPDDRs-2D) (see IEC 61496-3);
— AOPDs responsive to diffuse reflection that have one or more detection zone(s) specified in three
dimensions (AOPDDRs-3D) (see IEC 61496-3);
— vision based protective devices using reference pattern techniques (VBPDPP) (see IEC/TS 61496-4-2);
— vision based protective devices using stereo vision techniques (VBPDST) (see IEC/TS 61496-4-3);
b) pressure-sensitive mats and pressure-sensitive floors (see ISO 13856-1);
c) two-hand control devices (see ISO 13851);
d) single control devices;
e) interlocking guards (see ISO 14120).
This document is not applicable to:
— safeguards (e.g. pendant two-hand control devices) that can be manually moved, without using tools,
nearer to the hazard zone than the separation distance;
— protection against the risks from hazards arising from emissions (e.g. the ejection of solid or fluid
materials, radiation, electric arcs, heat, noise, fumes, gases);
— protection against the risks arising from failure of mechanical parts of the machine or gravity falls.
The separation distances derived from this document do not apply to safeguards used solely for presence
sensing function.
- Standard85 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Apr-2022
- 17-Mar-2025
- 13.110
- 13.180
- 2006/42/EC
- M/396
- VSN
This document defines terms which are used to describe power-driven brushes and strip brushes and
describes the designation system.
This document does not cover brushes for car wash sites, vacuum cleaners, carpet cleaning machines,
sewer and street cleaning machines, dental brushes, brushes for sealing and stripping.
- Standard77 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the design and metrological characteristics of coherence scanning interferometry (CSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.