SIST EN 1669:1998
(Main)Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip
Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip
This standard specifies the method for determining the ear height of sheet and strip of nominal thicknesses from 0,08 mm to 6 mm after deep drawing.
Aluminium und Aluminiumlegierungen - Prüfverfahren - Zipfelprüfung an Blechen und Bändern
Diese Norm legt ein Verfahren zur Bestimmung der Zipfelausbildung nach dem Näpfchenziehversuch fest. Sie gilt für Bleche und Bänder mit einer Nenndicke von 0,08 mm bis 6 mm.
Aluminium et alliages d'aluminium - Méthodes d'essai - Mesure de l'indice de cornes a l'emboutissage pour les tôles et les bandes
La présente norme spécifie la méthode qui permet de déterminer la hauteur des cornes apres emboutissage profond, sur une tôle ou une bande dont l'épaisseur nominale est comprise entre 0,08 mm et 6 mm.
Aluminij in aluminijeve zlitine - Metode preskušanja - Preskus ušesenja pločevine in trakov
General Information
Standards Content (sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Prüfverfahren - Zipfelprüfung an Blechen und BändernAluminium et alliages d'aluminium - Méthodes d'essai - Mesure de l'indice de cornes a l'emboutissage pour les tôles et les bandesAluminium and aluminium alloys - Test methods - Earing test for sheet and strip77.150.10Aluminijski izdelk
...This May Also Interest You
This document specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test pieces for these alloys.
Annex C is included as a guide to the selection of alloys for a specific use or process.
This document is intended to be used in conjunction with EN 576, EN 1559 1, EN 1559 4, EN 1676 and EN ISO 8062 3.
- Standard36 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard defines the requirements for grades of alloyed aluminium ingots intended for remelting.
It specifies the classifications and designations applicable to these grades, the conditions in which they are produced, their properties and the marks by which they are identified.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.
- Standard55 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European ...view more
- Standard97 pagesEnglish languagesale 10% offe-Library read for×1 day
TC request to delete an unnecessary and confusing Figure in publication
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard establishes temper designation for all forms of wrought aluminium and aluminium alloys and to continuously cast aluminium alloy drawing stock and strip intended to be wrought.
- Standard25 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see Figures 1 and 2). It applies to extruded products supplied without further surface treatment. Precision profiles covered in this standard are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
- they are mainly for architectural applications;
- ...view more
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy cold drawn rod/bar and tube. Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.
- Standard39 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft37 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where different or additional requirements are formulated and the appropriate alloys a...view more
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft18 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy extruded rod/bar, tube and profile for general engineering applications.
This European Standard does not apply to:
- forging stock (EN 603 (all parts),
- extruded precision profiles in alloys EN AW-6060 and EN AW-6063 (EN 12020) (all parts),
- products delivered in coils (EN 13957),
- coiled tubes cut to length (EN 13957).
- Standard19 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft18 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded porthole tubes with an outside diameter (OD) from 8 mm to 450 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 350 mm (other than round tube, see Figure 2), supplied in straight lengths.
This European Standard only applies to extruded porthole tube for general engineering applications made in the following alloys:
- E...view more
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft17 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded seamless tubes with an outside diameter (OD) from 8 mm to 450 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 350 mm (other than round tube, see Figure 2), supplied in straight lengths.
This European Standard only applies to tube produced by the seamless die/mandrel method of extrusion. This standard applies to extrud...view more
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft17 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm (see Figure 1).
The temper designations used in this part are according to EN 515.
This European Standard applies to extruded profiles for general engineering applications only.
- Standard20 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn porthole tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see Figure 2), supplied in straight lengths.
This document only applies to cold drawn tube for general engineering applications made in the following alloys:
- EN AW-1050A, EN ...view more
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft16 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloys cold drawn seamless tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see Figure 2) supplied in straight lengths.
This European Standard only applies to tube produced by the seamless die/mandrel method of extrusion (and then cold drawn to the fin...view more
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft16 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy extruded rod/bar, tube and profile.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 755-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.
- Standard58 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft58 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications.
This document applies to products which are extruded and then cold drawn.
This document does not apply to:
- forging stock (EN 603),
- products delivered in coils (EN 13958),
- coiled tubes cut to length (EN 13958).
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft17 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the material requirements and testing procedures applicable to wrought and cast aluminium and aluminium alloys intended for use in the production of pressure equipment, according to the definition given in European Pressure Equipment Directive 97/23/EC.
The standard covers:
- the products forms, grades and tempers of wrought and cast aluminium and aluminium alloys which may be used for such applications together with data for wrought and cast alloys over their...view more
- Standard79 pagesEnglish languagesale 10% offe-Library read for×1 day
- 05-Oct-2014
- 20-Mar-2016
- 77.150.10
- 2014/68/EU
- 97/23/EC
- M/071
- INEK
This document provides a guideline about manufacturing practices for rolled products in the thicknesses range between 35 and 200 µm having surface quality characteristics essential for production of aluminium semi-rigid containers, lids and disposable platters which are used in contact with foodstuff.
This document can be applied to the production cycle of the "rolled semi-finished goods". The document cannot be applied to the production process of containers, lids and disposable platters.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm.
It applies to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip.
It does not apply to co...view more
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.