SIST EN 12735-1:2002
(Main)Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes used for refrigeration and air-conditioning piping systems (i.e. piping, connections, repairs). These tubes are supplied in straight lengths in the hard or half-hard tempers, or in coils in the annealed temper.
Kupfer und Kupferlegierungen - Nahtlose Rundrohre aus Kupfer für die Kälte- und Klimatechnik - Teil 1: Rohre für Leitungssysteme
Diese Europäische Norm legt die Anforderungen, Probenentnahme, Prüfverfahren und Lieferbedingungen für
nahtlose Rundrohre aus Kupfer fest, die in Leitungssystemen der Kälte- und Klimatechnik (d. h. Rohrleitungen,
Verbindungen, Ausbesserungen) verwendet werden.
Diese Rohre werden in geraden Längen geliefert, hart oder halbhart, oder in Ringen, geglüht.
Cuivre et alliages de cuivre - Tubes ronds sans soudure en cuivre pour l'air conditionné et la réfrigération - Partie 1: Tubes pour canalisations
La présente norme européenne spécifie les exigences, le mode d'échantillonnage, les méthodes d'essai et les conditions de livraison applicables aux tubes ronds en cuivre sans soudure utilisés dans les circuits d'air conditionné et de réfrigération (c'est-a-dire : Canalisations, raccordements, réparations).
Ces tubes sont livrés en longueurs droites a l'état dur ou demi-dur ou bien en couronnes a l'état recuit.
Baker in bakrove zlitine - Nevarjene okrogle bakrene cevi za hladilno in klimatsko tehniko - 1. del: Cevi za napeljave
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Nevarjene okrogle bakrene cevi za hladilno in klimatsko tehniko - 1. del: Cevi za napeljaveKupfer und Kupferlegierungen - Nahtlose Rundrohre aus Kupfer für die Kälte- und Klimatechnik - Teil 1: Rohre für LeitungssystemeCuivre et alliages de cuivre - Tubes ronds sans soudure en cuivre pour l'air conditionné et la réfrigération - Partie 1: Tubes pour canalisationsCopper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems77.150.30Bakreni izdelkiCopper products23.040.15Cevi iz neželeznih kovinNon-ferrous metal pipesICS:Ta slovenski standard je istoveten z:EN 12735-1:2001SIST EN 12735-1:2002en01-februar-2002SIST EN 12735-1:2002SLOVENSKI
STANDARD
SIST EN 12735-1:2002
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12735-1April 2001ICS 23.040.15English versionCopper and copper alloys - Seamless, round copper tubes forair conditioning and refrigeration - Part 1: Tubes for pipingsystemsCuivre et alliages de cuivre - Tubes ronds sans soudure encuivre pour l'air conditionné et la réfrigération - Partie 1:Tubes pour canalisationsKupfer und Kupferlegierungen - Nahtlose Rundrohre ausKupfer für die Kälte- und Klimatechnik - Teil 1: Rohre fürLeitungssystemeThis European Standard was approved by CEN on 6 March 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12735-1:2001 ESIST EN 12735-1:2002
Page 2EN 12735-1:2001ContentsPagePageForeword.3 Introduction.41Scope.4 2Normative references .43Terms and definitions
.............44Designations
....................54.1Material
........................54.2Temper
.........................54.3Product
.........................55Ordering information
..............66Requirements
...................66.1Composition
.....................66.2Mechanical properties
..............76.3Dimensions and tolerances
..........76.4Drift expanding
...................106.5Surface quality
...................106.6Freedom from defects
..............107Sampling
.......................10
8Test methods
...................11
8.1Analysis
.......................11
8.2Tensile test
.....................11
8.3Hardness test
...................11
8.4Drift expanding test
...............11
8.5Residue test.11
8.6Eddy current test
.................11
8.7Retests
........................12
9Declaration of conformity and inspection documentation
.........12
9.1Declaration of conformity
...........12
9.2Inspection documentation
...........1210Packaging, marking and form of delivery
.......................1210.1Packaging and marking
............1210.2Form of delivery
.................13Annex ZA
(informative) Clauses of thisEuropean Standard addressing essentialrequirements or other provisions ofEU Directives .14Bibliography .15SIST EN 12735-1:2002
Page 3EN 12735-1:2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 133 "Copper and copper alloys", thesecretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latestby October 2001.Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 3.1 "Copper tubes"to prepare the following standard:EN 12735-1,
Copper and copper alloys — Seamless, round copper tubes for air conditioning and refrigeration —Part 1: Tubes for piping systems.This European Standard has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard.The attention of the user of this standard is drawn to the fact that national or local regulations or practices mightrestrict the choice of dimensions and tempers in the application of products conforming to this standard.This is one of a series of European Standards for copper and copper alloy tubes. Other products are specified asfollows:EN 1057,
Copper and copper alloys — Seamless, round copper tubes for water and gas in sanitary and heatingapplications.EN 12449,
Copper and copper alloys — Seamless, round tubes for general purposes.EN 12450,
Copper and copper alloys — Seamless, round copper capillary tubes.EN 12451,
Copper and copper alloys — Seamless, round tubes for heat exchangers.EN 12452,
Copper and copper alloys — Rolled, finned, seamless tubes for heat exchangers.EN 12735-2,
Copper and copper alloys — Seamless, round copper tubes for air conditioning and refrigeration —Part 2: Tubes for equipment.prEN 13348, Copper and copper alloys — Seamless, round copper tubes for medical gases.prEN 13349,
Copper and copper alloys — Pre-insulated copper tubes with solid covering.prEN 13600,
Copper and copper alloys — Seamless copper tubes for electrical purposes.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.SIST EN 12735-1:2002
Page 4EN 12735-1:2001IntroductionIt is recommended that tubes manufactured to this standard are certified as conforming to the requirements of thisstandard based on continuing surveillance which should be coupled with an assessment of a supplier's qualitymanagement system against EN ISO 9001.1 ScopeThis European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamlessround copper tubes used for refrigeration and air-conditioning piping systems (i.e. piping, connections, repairs).These tubes are supplied in straight lengths in the hard or half-hard tempers, or in coils in the annealed temper.2 Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references, the latest edition of thepublication referred to applies (including amendments).EN 1655,
Copper and copper alloys — Declarations of conformity.EN 1971,
Copper and copper alloys — Eddy current test for tubes. EN 10002-1,
Metallic materials — Tensile testing — Part 1: Method of test (at ambient temperature).EN 10204,
Metallic products — Types of inspection documents.EN 10234,
Metallic materials — Tube — Drift expanding test.EN ISO 6507-1,
Metallic materials — Vickers hardness test - Part 1: Test method (ISO 6507-1:1997).NOTE
Informative references to documents used in the preparation of this standard, and cited at the appropriate places in thetext, are listed in the bibliography.3 Terms and definitionsFor the purposes of this standard, the following terms and definitions apply:3.1 seamless round copper tubehollow semi-finished product, circular in cross-section, made of copper, having a uniform wall thickness, which at allstages of production has a continuous periphery3.2 mean diameterarithmetical mean of any two diameters normal to each other at the same cross-section of the tube3.3 deviation from circular formdifference between the maximum and minimum outside diameters measured at any one cross-section of the tubeSIST EN 12735-1:2002
Page 5EN 12735-1:20013.4 deviation from concentricityhalf of the difference between the maximum and minimum wall thicknesses at the same cross-section of the tube3.5
production batchdefinite quantity of products of the same form, the same temper and the same cross-sectional dimensions manufac-tured during the same production sequence under uniform conditions4 Designations4.1 Material4.1.1 GeneralThe material is designated either by symbol or number (see 6.1).4.1.2 SymbolThe material symbol designation is based on the designation system given in ISO 1190-1.NOTE
Although the material symbol designation used in this standard might be the same as that in other standards using thedesignation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same.4.1.3 NumberThe material number designation is in accordance with the system given in EN 1412.4.2 TemperFor the purposes of this standard, the following designation, which is in accordance with the system given inEN 1173, applies for the material temper (see Table 1):R.
Temper designated by the minimum value of tensile strength requirement for the product with mandatorytensile strength and elongation requirements.4.3 ProductThe product designation provides a standardized pattern of designation from which a rapid and unequivocaldescription of a product is conveyed in communication. It provides mutual comprehension at the international levelwith regard to products which meet the requirements of the relevant European Standard.The product designation is no substitute for the full content of the standard.The product designation for products to this standard shall consist of:–denomination (Copper tube);–number of this European Standard (EN 12735-1);–temper designation (see Table 1);–nominal cross-sectional dimensions: outside diameter × wall thickness (see Table 2).The derivation of a product designation is shown in the following example.SIST EN 12735-1:2002
Page 6EN 12735-1:2001EXAMPLE
Copper tube conforming to this standard, in temper R290 (hard), nominal outside diameter 28 mm, nominal wallthickness 1,5 mm, shall be designated as follows:5 Ordering informationIn order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and thesupplier, the purchaser shall state on his enquiry and order the following information:a)quantity of product required (length, mass);b)denomination (Copper tube);c)number of this European Standard (EN 12735-1);d)temper designation (see 4.2 and Table 1);e)nominal cross-sectional dimensions: outside diameter × wall thickness (see Table 2);f)nominal length (see 10.2);g)form of delivery (see 10.2).NOTE 1
It is recommended that the product designation, as described in 4.3 is used for items b)to e).NOTE 2
In addition, the purchaser may also state on the enquiry and the order special requirements if any.EXAMPLE 1
Ordering details for 500 m copper tube conforming to EN 12735-1, in temper R290 (hard), nominal outsidediameter 28 mm, nominal wall thickness 1,5 mm, nominal length 5 m, straight lengths:500 m Copper tube EN 12735-1 – R290 – 28 × 1,5– 5 m straight lengthsEXAMPLE 2
Ordering details
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.