Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data - Part 125: Explicit CAD assembly structure with Graphic Product and Manufacturing Information (PMI)

1.1 Introduction
This document defines the requirements for the long-term digital preservation of the presentation of Product and Manufacturing Information (PMI) with their possible links to the 3D explicit shape and geometry of CAD assembly structure. The goal is to preserve this 3D information, without loss, with respect to the geometry produced by the original CAD system, following the principles laid down in EN 9300 003 “Fundamentals and Concepts”.
This will allow the retrieval of the assembly structure including the placement information.
This standard extends EN 9300-115 “Explicit CAD Assembly Structure” by including assembly level PMI.
PMI for the assembly structure can be recorded in the same file as the geometry, can be in a nested assembly structure or the PMI will be contained in its own separate file (Side-Car).
The PMI elements shall be presented on the graphic level only (i.e. polyline, tessellated).
1.2 Out of scope
The following is outside the scope:
- The archiving of assembly Form Features.
- Semantic PMI representation is out of scope for this document.
- The geometry defined at assembly level is out of scope for this document.
(This document covers PMI at the assembly level only.)

Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und - Bereitstellung digitaler technischer Produktdokumentationen, wie zum Beispiel von 3D , CAD und PDM-Daten - Teil 125: Eindeutige CAD-Baugruppenstruktur mit grafischen Produkt und Fertigungsinformationen (PMI)

Série aérospatiale - LOTAR - Archivage long terme et récupération des données techniques produits numériques telles que CAO, 3D et PDM - Partie 125 : Structure d’assemblage CAO explicite avec données graphiques de produit et de fabrication (PMI)

Aeronavtika - LOTAR - Dolgoročno arhiviranje in pridobivanje digitalne tehnične dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 125. del: Eksplicitna struktura sestavljanja CAD z informacijami o grafičnem izdelku in proizvodnji (PMI)

1.1 Uvod
Ta dokument določa zahteve za dolgoročno digitalno shranjevanje predstavitve informacij o grafičnem izdelku in proizvodnji (PMI) z morebitnimi povezavami do 3D eksplicitne oblike in geometrije strukture sestavljanja CAD. Cilj je ohraniti te 3D informacije brez izgub podatkov glede na geometrijo, ki jo proizvede prvotni sistem CAD, v skladu z načeli, določenimi v standardu EN 9300-003 »Osnove in pojmi«.
S tem bo omogočena pridobitev strukture sestavljanja, vključno z informacijami o postavitvi.
Ta standard razširja standard EN 9300-115 »Eksplicitna struktura sestavljanja CAD« z vključitvijo informacij o grafičnem izdelku in proizvodnji na ravni sestavljanja.
Informacije o grafičnem izdelku in proizvodnji za strukturo sestavljanja je mogoče beležiti v isti datoteki kot geometrijo, v ugnezdeni strukturi sestavljanja ali v ločeni datoteki (Side-Car).
Elementi informacij o grafičnem izdelku in proizvodnji morajo biti predstavljeni izključno na ravni grafike (tj. lomljeno, mozaično).
1.2 Zunaj področja uporabe
Naslednje ne spada na področje uporabe:
– arhiviranje oblikovnih lastnosti sestavljanja;
– semantična predstavitev informacij o grafičnem izdelku in proizvodnji ne spada na področje uporabe tega dokumenta;
– geometrija, opredeljena na ravni sestavljanja, ne spada na področje uporabe tega dokumenta.
(Ta dokument obravnava samo informacije o grafičnem izdelku in proizvodnji na ravni sestavljanja.)

General Information

Status
Published
Public Enquiry End Date
14-Sep-2022
Publication Date
19-Nov-2023
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Nov-2023
Due Date
21-Jan-2024
Completion Date
20-Nov-2023

Buy Standard

Standard
EN 9300-125:2024 - BARVE
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 9300-125:2022 - BARVE
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 9300-125:2024
01-januar-2024
Aeronavtika - LOTAR - Dolgoročno arhiviranje in pridobivanje digitalne tehnične
dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 125. del: Eksplicitna
struktura sestavljanja CAD z informacijami o grafičnem izdelku in proizvodnji (PMI)
Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical
product documentation such as 3D, CAD and PDM data - Part 125: Explicit CAD
assembly structure with Graphic Product and Manufacturing Information (PMI)
Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und - Bereitstellung digitaler
technischer Produktdokumentationen, wie zum Beispiel von 3D , CAD und PDM-Daten -
Teil 125: Eindeutige CAD-Baugruppenstruktur mit grafischen Produkt und
Fertigungsinformationen (PMI)
Série aérospatiale - LOTAR - Archivage long terme et récupération des données
techniques produits numériques telles que CAO, 3D et PDM - Partie 125 : Structure
d’assemblage CAO explicite avec données graphiques de produit et de fabrication (PMI)
Ta slovenski standard je istoveten z: EN 9300-125:2023
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
35.240.30 Uporabniške rešitve IT v IT applications in information,
informatiki, dokumentiranju in documentation and
založništvu publishing
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
SIST EN 9300-125:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 9300-125:2024

---------------------- Page: 2 ----------------------
SIST EN 9300-125:2024


EN 9300-125
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2023
EUROPÄISCHE NORM
ICS 01.110
English Version

Aerospace series - LOTAR - LOng Term Archiving and
Retrieval of digital technical product documentation such
as 3D, CAD and PDM data - Part 125: Explicit CAD
assembly structure with Graphic Product and
Manufacturing Information (PMI)
Série aérospatiale - LOTAR - Archivage long terme et Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung
récupération des données techniques produits und - Bereitstellung digitaler technischer
numériques telles que CAO, 3D et PDM - Partie 125 : Produktdokumentationen, wie zum Beispiel von 3D ,
Structure d'assemblage CAO explicite avec données CAD und PDM-Daten - Teil 125: Eindeutige CAD-
graphiques de produit et de fabrication (PMI) Baugruppenstruktur mit grafischen Produkt und
Fertigungsinformationen (PMI)
This European Standard was approved by CEN on 22 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 9300-125:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 9300-125:2024
EN 9300-125:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
1.1 General . 4
1.2 Out of scope . 4
2 Normative references .
...

SLOVENSKI STANDARD
oSIST prEN 9300-125:2022
01-september-2022
Aeronavtika - LOTAR - 125. del: Eksplicitna struktura sestavljanja CAD z
informacijami o grafičnem izdelku in proizvodnji (PMI)
Aerospace series - LOTAR - Part 125: Explicit CAD assembly structure with Graphic
Product and Manufacturing Information (PMI)
Luft- und Raumfahrt - LOTAR - Teil 125: Explizite CAD Baugruppenstruktur mit Grafik
Produkt- und Herstellungsrelevanten Informationen
Série aérospatiale - LOTAR - Archivage long terme et récupération des données
techniques produits numériques telles que CAO 3D et PDM - Partie 125 : Structure
d'assemblage explicite CAO avec données graphiques de produit et de fabrication (PMI)
Ta slovenski standard je istoveten z: prEN 9300-125
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
35.240.30 Uporabniške rešitve IT v IT applications in information,
informatiki, dokumentiranju in documentation and
založništvu publishing
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
oSIST prEN 9300-125:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 9300-125:2022

---------------------- Page: 2 ----------------------
oSIST prEN 9300-125:2022


DRAFT
EUROPEAN STANDARD
prEN 9300-125
NORME EUROPÉENNE

EUROPÄISCHE NORM

June 2022
ICS 01.110
English Version

Aerospace series - LOTAR - Part 125: Explicit CAD
assembly structure with Graphic Product and
Manufacturing Information (PMI)
Série aérospatiale - LOTAR - Archivage long terme et Luft- und Raumfahrt - LOTAR - Teil 125: Explizite CAD
récupération des données techniques produits Baugruppenstruktur mit Grafik Produkt- und
numériques telles que CAO 3D et PDM - Partie 125 : Herstellungsrelevanten Informationen
Structure d'assemblage explicite CAO avec données
graphiques de produit et de fabrication (PMI)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 9300-125:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 9300-125:2022
FprEN 9300-125:2022 (E)
Contents

European foreword . 4
1 Scope . 5
1.1 Introduction . 5
1.2 Out of scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
4 Applicability .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.