SIST EN 12392:2016/oprA1:2019
(Amendment)Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
This European Standard specifies the material requirements and testing procedures applicable to wrought and cast aluminium and aluminium alloys intended for use in the production of pressure equipment, according to the definition given in European Pressure Equipment Directive 97/23/EC.
The standard covers:
- the products forms, grades and tempers of wrought and cast aluminium and aluminium alloys which may be used for such applications together with data for wrought and cast alloys over their permissible working temperature ranges;
- the permissible alloys/ tempers covered by this are those given in Table A.1 and in B.1 for wrought alloys and in Table A.2 and in B.2 for castings;
- the technical conditions for inspection and delivery, mechanical property limits and tolerances on form and dimensions by reference to the appropriate European standards for the relevant wrought and cast aluminium and aluminium alloys, and
- additional requirements which are specific to pressure equipment applications.
It applies to hot-rolled plate, cold-rolled sheet/ strip/ circles, extruded or extruded and cold drawn rod/bar, tube, extruded open / hollow profiles, forgings and castings.
It is the sole objective of this standard to cover materials only for pressure purposes and it excludes any elements of fabrication or fabrication methods for pressure equipment; such information can be found in the relevant standards listed in the 'Bibliography' section.
Aluminium und Aluminium Legierungen - Knet- und Gusserzeugnisse - Besondere Anforderungen an Erzeugnisse für die Fertigung von Druckgeräten
Aluminium et alliage d'aluminium - Produits corroyés et moulés - Exigences particulières pour les produits destinés à la fabrication des appareils à pression
Aluminij in aluminijeve zlitine - Gnetne in ulite zlitine - Posebne zahteve za aluminijeve izdelke za izdelavo naprav, ki delajo pod tlakom - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12392:2016/oprA1:2019
01-julij-2019
Aluminij in aluminijeve zlitine - Gnetne in ulite zlitine - Posebne zahteve za
aluminijeve izdelke za izdelavo naprav, ki delajo pod tlakom - Dopolnilo A1
Aluminium and aluminium alloys - Wrought products and cast products - Special
requirements for products intended for the production of pressure equipment
Aluminium und Aluminium Legierungen - Knet- und Gusserzeugnisse - Besondere
Anforderungen an Erzeugnisse für die Fertigung von Druckgeräten
Aluminium et alliage d'aluminium - Produits corroyés et moulés - Exigences particulières
pour les produits destinés à la fabrication des appareils à pression
Ta slovenski standard je istoveten z: EN 12392:2016/prA1
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 12392:2016/oprA1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12392:2016/oprA1:2019
---------------------- Page: 2 ----------------------
SIST EN 12392:2016/oprA1:2019
DRAFT
EUROPEAN STANDARD
EN 12392:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2019
ICS 77.150.10
English Version
Aluminium and aluminium alloys - Wrought products and
cast products - Special requirements for products intended
for the production of pressure equipment
Aluminium et alliage d'aluminium - Produits corroyés Aluminium und Aluminium Legierungen - Knet- und
et moulés - Exigences particulières pour les produits Gusserzeugnisse - Besondere Anforderungen an
destinés à la fabrication des appareils à pression Erzeugnisse für die Fertigung von Druckgeräten
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 132.
This draft amendment A1, if approved, will modify the European Standard EN 12392:2016. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserve
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.