SIST EN 13210-2:2021
(Main)Child care articles - Part 2: Children's harnesses incorporating backpacks and reins - Safety requirements and test methods
Child care articles - Part 2: Children's harnesses incorporating backpacks and reins - Safety requirements and test methods
Part 2 of this European standard specifies the minimum safety requirements
and test methods for children's harnesses incorporating backpacks and/or
toys with a leading rein for restraining children when walking, with the ability
to walk competently and for use up to 48 months of age.
If the product has other functions not covered in this European standard,
reference should be made to the relevant European standard.
Artikel für Säuglinge und Kleinkinder - Teil 2: Sicherheitsgeschirre einschließlich Rucksäcken und Zügeln - Sicherheitsanforderungen und Prüfverfahren
Dieses Dokument legt die Mindest Sicherheitsanforderungen an und Prüfverfahren für Sicherheitsgeschirre für Kinder mit integrierten Rucksäcken und/oder Spielzeugen und mit Führungszügel zum Zurückhalten eines Kindes, das bereits sicher laufen kann, beim Laufen zur Nutzung für Kinder bis 48 Monate fest.
Wenn das Produkt Funktionen aufweist, die nicht von diesem Dokument behandelt werden, kann die entsprechende Europäische Norm herangezogen werden.
Articles de puériculture - Partie 2 : Harnais équipés de sacs à dos et de laisses de promenade pour enfants - Exigences de sécurité et méthodes d’essai
Le présent document spécifie les exigences minimales de sécurité et les méthodes d’essai applicables aux harnais équipés de sacs à dos et/ou de jouets et d’une laisse simple servant à limiter les déplacements des enfants qui savent marcher et jusqu’à l’âge de 48 mois.
Si le produit possède d’autres fonctions non couvertes par le présent document, la Norme européenne correspondante peut être consultée.
Izdelki za otroke - 2. del: Otroški pasovi, ki so del nahrbtnika, in vajeti - Varnostne zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13210-2:2021
01-februar-2021
Nadomešča:
SIST EN 13210:2005
Izdelki za otroke - 2. del: Otroški pasovi, ki so del nahrbtnika, in vajeti - Varnostne
zahteve in preskusne metode
Child care articles - Part 2: Children's harnesses incorporating backpacks and reins -
Safety requirements and test methods
Artikel für Säuglinge und Kleinkinder - Teil 2: Sicherheitsgeschirre einschließlich
Rucksäcken und Zügeln - Sicherheitsanforderungen und Prüfverfahren
Articles de puériculture - Partie 2 : Harnais équipés de sacs à dos et de laisses de
promenade pour enfants - Exigences de sécurité et méthodes d’essai
Ta slovenski standard je istoveten z: EN 13210-2:2020
ICS:
97.190 Otroška oprema Equipment for children
SIST EN 13210-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13210-2:2021
---------------------- Page: 2 ----------------------
SIST EN 13210-2:2021
EN 13210-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2020
EUROPÄISCHE NORM
ICS 97.190 Supersedes EN 13210:2004
English Version
Child care articles - Part 2: Children's harnesses
incorporating backpacks and reins - Safety requirements
and test methods
Articles de puériculture - Partie 2 : Harnais équipés de Artikel für Säuglinge und Kleinkinder - Teil 2:
sacs à dos et de laisses de promenade pour enfants - Sicherheitsgeschirre mit integrierten Rucksäcken und
Exigences de sécurité et méthodes d'essai Zügeln - Sicherheitsanforderungen und Prüfverfahren
This European Standard was approved by CEN on 17 August 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13210-2:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test equipment . 5
5 General test conditions . 9
6 Chemical hazards . 9
7 Thermal hazards . 10
8 Mechanical hazards . 10
9 Product information . 16
Annex A (informative) Rationales . 18
A.1 General. 18
A.2 Chemical hazards . 18
A.3 Thermal hazards . 18
A.4 Mechanical hazards . 18
Bibliography . 20
2
---------------------- Page: 4 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
European foreword
This document (EN 13210-2:2020) has been prepared by Technical Committee CEN/TC 252 “Child care
articles”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document, together with EN 13210-1:2020, supersedes EN 13210:2004.
This document has been prepared under mandate M/264 given to CEN by the European Commission and
the European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
1 Scope
This document specifies the minimum safety requirements and test methods for children's harnesses
incorporating backpacks and/or toys with a leading rein for restraining children when walking, with the
ability to walk competently and for use up to 48 months of age.
If the product has other functions not covered in this document, the relevant European standard can be
consulted.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 71-1, Safety of toys - Part 1: Mechanical and physical properties
EN 71-2:2011+A1:2014, Safety of toys - Part 2: Flammability
EN 71-3:2019, Safety of toys - Part 3: Migration of certain elements
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
harness with backpack or toy
restraint system designed to fit around the child’s torso comprising a strap or fabric assembly or a
combination of both incorporating a storage bag or toy, a grab handle and/or attachment point(s) for a
leading rein (3.8)
Note 1 to entry: See Figure 1.
3.2
backpack
storage bag worn on the child’s back
3.3
toy
toy, clothed or unclothed, with soft body surfaces and filled with soft materials, readily allowing
compression of the main part of the toy with the hand or useable as a storage bag, or a combination of
both, attached to a harness or with an integral harness and worn on the child’s back
4
---------------------- Page: 6 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
Figure 1 — Example of a harness incorporating a backpack
3.4
waist belt
part of the harness which passes around the child’s torso
3.5
shoulder straps
parts of the harness which pass over each shoulder of the child
3.6
chest strap
strap(s) or a fastening system or combination of both which is attached to the shoulder straps and
positioned across the front of the child’s torso
3.7
grab handle
short strap fixed at both ends at the top of the backpack/toy
3.8
leading rein
single continuous strap which is attached at a single point to the harness/backpack/toy with a wrist loop
or a hand grip to be held by the carer
4 Test equipment
4.1 Test frame
Rigid test frame comprising:
— two horizontal members against which the test dummy top eyebolt and bottom clamp may be secured
by bolts or clamps;
— 75 mm diameter convey belt roller positioned with a horizontal gap of (250 ± 10) mm between the
test dummy and roller. It shall be possible to adjust the height of the roller and/or the horizontal
members supporting the test dummy;
5
---------------------- Page: 7 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
— height adjustable dynamic mass release mechanism (See Figure 2).
Dimensions in millimetres
Key
1 horizontal members
2 test dummy
3 roller
4 dynamic mass release mechanism
Figure 2 — Test frame
6
---------------------- Page: 8 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
4.2 Test dummy
Dummy comprising:
— bag 300 mm wide and 470 mm long filled with dry compacted sand, so that the whole constitutes a
rigid form (see Figure 3);
— inside the closed end of the bag is a rectangular metal bar, 260 mm long, 25 mm high and 6 mm wide
connected at the centre of its length to an eyebolt passing through an eyelet;
— the open end of the bag shall be sewn closed 50 mm from the bottom of the bag and clamped between
two rectangular bars, of minimum dimensions 400 mm long, 25 mm high and 6 mm wide each with
four holes drilled with the centres 160 mm and 180 mm from the centre of the bar and secured with
nuts and bolts through the inner holes. Additional holes may be drilled in the bar to ensure that the
bag is securely clamped. The outer holes enable the bottom of the dummy to be secured to the
horizontal beam of the test frame.
Dimensions in millimetres
Key
1 eyebolt
2 bag
3 clamp
Figure 3 — Test dummy
7
---------------------- Page: 9 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
4.3 Test mass assembly
4.3.1 General
Assembly that includes shackles, spring, static mass and dynamic mass. The total mass of the assembly
shall be (12 ± 0,1) kg.
The dynamic mass shall be (5 ± 0,05) kg and be capable of falling freely from a height of 300 mm (see
Figure 4).
Dimensions in millimetres
Key
1 top shackles
2 suspension bar
3 shackle
4 spring
5 dynamic mass
6 release mechanism
7 test frame
8 static mass
Figure 4 — Test mass assembly
8
---------------------- Page: 10 ----------------------
SIST EN 13210-2:2021
EN 13210-2:2020 (E)
4.3.2 Spring
A spring with the following characteristics shall be used to support the static and dynamic mass from the
suspension bar:
Stiffness (28 000 ± 10 %) N/M;
Diameter of wire 3 mm;
External diameter 16 mm;
Length without load 45mm ± 5 mm.
4.3.3 Shackles
Shackles shall have a diameter of 10 mm at the roundest end.
4.3.4 Release mechanism
Bar or rod supported by the test frame which is withdrawn to release the dynamic mass.
4.3.5 Grab handle test strap
A piece of (47 ± 3) mm wide webbing with a loop sewn into each end. The length of the strap including
loops shall be (1 200 ± 50) mm.
NOTE Vehicle seat belt webbing fits this criteria.
5 General test conditions
5.1 General
The tests shall be carried out in the order that they are listed in this document and on one sample, unless
otherwise stated.
5.2 Tolerances
Unless stated otherwise, all forces, masses and dimensions of the test equipment shall have tolerances as
follows:
— forces ± 5 %;
— masses ± 0,5 %;
— dimensions ± 0,5 mm.
6 Chemical hazards
A separate unconditioned sample shall be used for this test.
Migration of elements from s
...
SLOVENSKI STANDARD
oSIST prEN 13210-2:2019
01-april-2019
Izdelki za otroke - 2. del: Otroški pasovi, ki so del nahrbtnika, in vajeti - Varnostne
zahteve in preskusne metode
Child care articles - Part 2: Children's harnesses incorporating backpacks and reins -
Safety requirements and test methods
Artikel für Säuglinge und Kleinkinder - Teil 2: Sicherheitsgeschirre einschließlich
Rucksäcken und Zügeln - Sicherheitsanforderungen und Prüfverfahren
Ta slovenski standard je istoveten z: prEN 13210-2
ICS:
97.190 Otroška oprema Equipment for children
oSIST prEN 13210-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13210-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN 13210-2:2019
DRAFT
EUROPEAN STANDARD
prEN 13210-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2019
ICS 97.190 Will supersede EN 13210:2004
English Version
Child care articles - Part 2: Children's harnesses
incorporating backpacks and reins - Safety requirements
and test methods
Artikel für Säuglinge und Kleinkinder - Teil 2:
Sicherheitsgeschirre einschließlich Rucksäcken und
Zügeln - Sicherheitsanforderungen und Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 252.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13210-2:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Test equipment . 6
4.1 Test frame . 6
4.2 Test dummy . 7
4.3 Test mass assembly . 8
4.3.1 General. 8
4.3.2 Spring . 9
4.3.3 Shackles . 9
4.3.4 Release mechanism . 9
4.3.5 Grab handle test strap . 9
5 General test conditions . 10
5.1 General. 10
5.2 Tolerances . 10
5.3 Conditioning . 10
6 Chemical hazards . 11
7 Thermal hazards . 11
7.1 Flammability . 11
7.1.1 Requirements . 11
7.1.2 Test methods . 12
8 Mechanical hazards . 12
8.1 Protective function . 12
8.1.1 General. 12
8.1.2 Harness with backpack/toy . 12
8.1.3 Waist belt and chest strap . 12
8.1.4 Shoulder straps . 12
8.1.5 Leading rein . 12
8.2 Structural integrity . 12
8.2.1 Requirements . 12
8.2.2 Test method for harness/backpack/toy with a leading rein . 13
8.2.3 Test method for harness/backpack/toy with a grab handle . 15
8.3 Entanglement . 17
8.3.1 General. 17
8.3.2 Cords, ribbons and parts used as ties . 17
8.4 Choking and ingestion . 17
8.4.1 Requirement . 17
8.4.2 Test method . 17
8.5 Suffocation from packaging materials . 17
8.6 Edges, projections and corners . 17
9 Product information . 17
9.1 General. 17
9.2 Purchase information. 18
9.3 Marking . 18
9.3.1 Requirements . 18
2
---------------------- Page: 4 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
9.3.2 Instructions for use . 18
Annex A (informative) Warnings . 19
Bibliography . 21
3
---------------------- Page: 5 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
European foreword
This document (prEN 13210-2:2019) has been prepared by Technical Committee CEN/TC 252 “Child use
and care articles”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13210:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
4
---------------------- Page: 6 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
1 Scope
This document specifies the minimum safety requirements and test methods for children's harnesses
incorporating backpacks and/or toys with a leading rein for restraining children when walking, with the
ability to walk competently and for use up to 48 months of age.
If the product has other functions not covered in this document, the relevant European standard can be
consulted.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 71-1, Safety of toys — Part 1: Mechanical and physical properties
EN 71-2:2011+A1:2014, Safety of toys — Part 2: Flammability
EN 71-3, Safety of toys — Part 3: Migration of certain elements
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
harness with backpack or toy
restraint system designed to fit around a child’s torso comprising a strap or fabric assembly or a
combination of both incorporating a storage bag or toy, a grab handle and/or attachment point(s) for a
leading rein (3.8)
Note 1 to entry: See Figure 1.
Figure 1 — Example of a harness incorporating a backpack
5
---------------------- Page: 7 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
3.2
backpack
storage bag worn on the child’s back
3.3
toy
toy with a soft body surface which may be filled with soft material or useable as a storage bag, or a
combination of both, worn on the child’s back
3.4
waist belt
part of the harness which passes around the child’s torso
3.5
shoulder straps
parts of the harness which pass over each shoulder of the child
3.6
chest strap
strap(s) or a fastening system or combination of both which is attached to the shoulder straps and
positioned across the front of the child’s torso
3.7
grab handle
short strap fixed at both ends at the top of the backpack/toy
3.8
leading rein
rein which comprises a single continuous strap which is attached at a single point to the
harness/backpack/toy
4 Test equipment
4.1 Test frame
Rigid test frame comprising:
— two horizontal members against which the test dummy top eyebolt and bottom clamp may be
secured by bolts or clamps;
— 75 mm diameter convey belt roller positioned with a horizontal gap of (250 ± 10) mm between the
test dummy and roller. It shall be possible to adjust the height of the roller and/or the horizontal
members supporting the test dummy;
— height adjustable dynamic mass release mechanism(See Figure 2).
6
---------------------- Page: 8 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
Key
1 horizontal members
2 test dummy
3 roller
4 dynamic mass release mechanism
Figure 2 — Test frame
4.2 Test dummy
Dummy comprising:
Bag 300 mm wide and 470 mm long filled with dry compacted sand, so that the whole constitutes a rigid
form (see Figure 3);
— inside the closed end of the bag is a rectangular metal bar, 260 mm long, 25 mm high and 6 mm wide
connected at the centre of its length to an eyebolt passing through an eyelet;
7
---------------------- Page: 9 ----------------------
oSIST prEN 13210-2:2019
prEN 13210-2:2019 (E)
— the open end of the bag shall be sewn osed 50 mm from the bottom of the bag and clamped between
two rectangular bars, of minimum dimensions 400 mm long, 25 mm high and 6 mm wide each with
four holes drilled with the centres 160 mm and 180 mm from the centre of the bar and secured with
nuts and bolts through the inner holes. Additional holes may be drilled in the bar to ensure that the
bag is securely clamped. The outer holes enable the bottom of the dummy to be secured to the
horizontal beam of the test frame.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.