SIST EN 14420-7:2022
(Main)Hose fittings with clamp units - Part 7: Cam locking couplings
Hose fittings with clamp units - Part 7: Cam locking couplings
This document specifies the design, materials, dimensions and marking requirements for cam locking couplings that serve as the link between hoses and connections to transport liquids, solids and gases, except liquid gas and steam. The couplings are capable of operating within the pressure range −0,8 bar1 to 16 bar and in a working temperature range of −20 °C up to +65 °C. For all sizes of aluminium-cast-material couplings and for all couplings size DN 100 the pressure range is from −0,8 bar to 10 bar.
Schlaucharmaturen mit Klemmfassungen - Teil 7: Hebelarmkupplungen
Dieses Dokument legt die Konstruktion, Werkstoffe, Maße und Anforderungen zur Kennzeichnung für Hebelarmkupplungen fest, die der Verbindung von Schläuchen mit Anschlüssen zum Fördern von Flüssigkeiten, Feststoffen und Gasen, ausgenommen Flüssiggas und Dampf, dienen. Die Kupplungen müssen in einem Druckbereich von −0,8 bar1) bis 16 bar und in einem Arbeitstemperaturbereich von −20 °C bis +65 °C verwendet werden können. Für alle Größen von Aluminium-Guss-Kupplungen und für alle Kupplungen der Größe DN 100 ist der Druckbereich −0,8 bar bis 10 bar.
Raccords pour flexibles avec demi-coquille - Partie 7 : Raccords à cames
Le présent document spécifie la conception, les matériaux, les dimensions et le marquage des raccords à cames destinés à relier les tuyaux et les connexions pour le transport de liquides, de matières solides et de gaz, à l'exception des gaz liquéfiés et de la vapeur. Les raccords sont utilisables dans une plage de pression de service de -0,8 bar1 à 16 bar et dans un plage de températures de service de -20 °C à + 65 °C.
Pour toutes les dimensions de raccords en aluminium moulé et pour tous les raccords de dimension
DN 100, la plage de pression est de -0,8 bar à 10 bar.
Cevni fitingi z objemkami - 7. del: Spojke z vzvodno ročico
Ta dokument določa zasnovo, materiale, dimenzije in zahteve za označevanje za spojke z vzvodno ročico, ki povezujejo cevi in priključke za prevoz tekočin, trdnih snovi in plinov, razen tekočega plina in pare. Spojke ustrezno delujejo pri delovnem tlaku v razponu od −0,8 bara do 16 barov in v temperaturnem območju od −20 °C do +65 °C. Razpon delovnega tlaka za materiale iz litega aluminija vseh velikosti in za vse spojke velikosti DIN 100 je od −0,8 bara do 10 barov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 14420-7:2022
01-oktober-2022
Nadomešča:
SIST EN 14420-7:2013
Cevni fitingi z objemkami - 7. del: Spojke z vzvodno ročico
Hose fittings with clamp units - Part 7: Cam locking couplings
Schlaucharmaturen mit Klemmfassungen - Teil 7: Hebelarmkupplungen
Raccords pour flexibles avec demi-coquille - Partie 7 : Raccords à cames
Ta slovenski standard je istoveten z: EN 14420-7:2022
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST EN 14420-7:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 14420-7:2022
---------------------- Page: 2 ----------------------
SIST EN 14420-7:2022
EN 14420-7
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2022
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN 14420-7:2013
English Version
Hose fittings with clamp units - Part 7: Cam locking
couplings
Raccords pour flexibles avec demi-coquille - Partie 7 : Schlaucharmaturen mit Klemmfassungen - Teil 7:
Raccords à cames Hebelarmkupplungen
This European Standard was approved by CEN on 24 July 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14420-7:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Requirements . 7
4.1 Construction . 7
4.2 Temperatures . 7
5 Survey . 7
6 Types of connection. 9
7 Designation. 10
8 Dimensions . 10
8.1 General . 10
8.2 Coupler types . 10
8.3 Cam arm (item No. 2) . 16
8.4 Pin (item No. 3) . 18
8.5 Ring (item No. 4) . 18
8.6 Main gasket (item No. 5) . 19
8.7 Thread gasket (item No. 6) . 20
8.8 Adapter types . 20
9 Materials . 25
9.1 General . 25
9.2 Coupler and adapter body . 25
9.3 Cam arm (item No. 2) . 26
9.4 Pin (item No. 3) . 26
9.5 Ring (item No. 4) . 26
9.6 Main gasket (item No. 5) . 26
9.7 Thread gasket (item No. 6) . 26
10 Marking . 27
11 Type testing and quality control . 27
Annex A (normative) Gauges for cam-locking couplings . 28
Bibliography . 30
2
---------------------- Page: 4 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
European foreword
This document (EN 14420-7:2022) has been prepared by Technical Committee CEN/TC 218 “Rubber and
plastics hoses and hose assemblies”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2023, and conflicting national standards shall
be withdrawn at the latest by February 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14420-7:2013.
In comparison to EN 14420-7:2013, the following changes have been made:
— In Clause 2, the Normative references have been updated;
— The Scope of the document has been changed.
The EN 14420 series, Hose fittings with clamp units, consists of the following parts:
— Part 1: Requirements, types of fixing and connection, designation and testing
— Part 2: Hose side parts of hose tail
— Part 3: Clamp units, bolted or pinned
— Part 4: Flange connections
— Part 5: Threaded connections
— Part 6: TW tank truck couplings
— Part 7: Cam locking couplings
— Part 8: Symmetrical half coupling (Guillemin system)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
Introduction
Cam locking couplings are manufactured worldwide according to the American “military specification”
MIL-C-27487. This American standard fixes the coupling side in a limited way, but not the connection
side. Other parts like levers, bolts, ring and gaskets are not standardized.
4
---------------------- Page: 6 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
1 Scope
This document specifies the design, materials, dimensions and marking requirements for cam locking
couplings that serve as the link between hoses and connections to transport liquids, solids and gases,
except liquid gas and steam.
For all sizes of aluminium cast material couplings and for all couplings of size DN 100, the pressure range
is from −0,8 bar to 10 bar in the working temperature range from −20 °C to +65 °C. All other couplings
1
according to this document are capable of operating within the pressure range from 0,8 bar to 16 bar in
the working temperature range from −20 °C to +65 °C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 755-2, Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical
properties
EN 1706, Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN 1982, Copper and copper alloys - Ingots and castings
EN 10088-1, Stainless steels - Part 1: List of stainless steels
EN 10213, Steel castings for pressure purposes
EN 10226-1, Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external
threads and parallel internal threads - Dimensions, tolerances and designation
EN 12420, Copper and copper alloys - Forgings
EN 14420-1:2013, Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection,
designation and testing
EN 14420-2, Hose fittings with clamp units - Part 2: Hose side parts of hose tail
EN 14420-5, Hose fittings with clamp units - Part 5: Threaded connections
EN 22768-1, General tolerances - Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications (ISO 2768-1)
2
EN 22768-2 , General tolerances - Part 2: Geometrical tolerances for features without individual tolerance
indications (ISO 2768-2)
EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions,
tolerances and designation (ISO 228-1)
1
1 bar = 0,1 MPa.
2
EN 22768-2 has been withdrawn and replaced by EN ISO 22081.
5
---------------------- Page: 7 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
EN ISO 683-1, Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for
quenching and tempering (ISO 683-1)
EN ISO 8330, Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330)
ISO 272, Fasteners — Hexagon products — Widths across flats
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 8330 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
DN
nominal size
alphanumeric designation of size for components of a pipework system, which is used for reference
purposes, comprised of the letters DN followed by a dimensionless whole number which is indirectly
related to the physical size, in millimetres, of the bore or outside diameter of the end connections
Note 1 to entry: The number following the letters DN does not represent a measurable value and is not be used
for calculation purposes except where specified in the relevant standard.
Note 2 to entry: In those standards which use the DN designation system, any relationship between DN and
component dimensions is to be indicated, e.g. DN/OD or DN/ID.
[SOURCE: EN ISO 6708:1995, 2.1, modified]
3.2
PN
alphanumeric designation used for reference purposes related to a combination of mechanical and
dimensional characteristics of a component of a hose fitting
Note 1 to entry: It comprises the letters PN followed by a dimensionless number.
Note 2 to entry: The number following the letters PN does not represent a measurable value and should not be
used for calculation purposes except where specified in the relevant standard.
3.3
main gasket
interface gasket between the male and female part of a coupling
3.4
thread gasket
flat faced gasket for threads according to EN ISO 228-1
6
---------------------- Page: 8 ----------------------
SIST EN 14420-7:2022
EN 14420-7:2022 (E)
4 Requirements
4.1 Construction
The curves of the lever and the adapters as well as the dimensions of the main gaskets shall be
harmonized such that twisting of the hose and vibrating during operation shall not lead to leakage. Cam
arms shall be manually operable.
Cam arms shall be suitable to operate without using tools.
For gauges for cam-locking couplings according to this document see Annex A.
NOTE If the requirements of this document are met, compatibility between couplers and adapters from
different manufacturers is ensured. Apart from gaskets, the interchangeability between spare parts from different
manufacturers cannot be ensured.
4.2 Temperatures
Range of working temperatures of couplings equipped with nitrile butadiene rubber gasket
(NBR-gasket): −20 °C to +65 °C.
5 Survey
Figure 1 and Figure 2 show examples for cam-locking couplings. A parts list is given in Table 1.
NOTE Chain optional.
Figure 1 — Coupler type DF and adapter
...
SLOVENSKI STANDARD
oSIST prEN 14420-7:2021
01-september-2021
Cevni fitingi z objemkami - 7. del: Spojke z vzvodno ročico
Hose fittings with clamp units - Part 7: Cam locking couplings
Schlaucharmaturen mit Klemmfassungen - Teil 7: Hebelarmkupplungen
Raccords pour flexibles avec demi-coquille - Partie 7: Raccords à cames
Ta slovenski standard je istoveten z: prEN 14420-7
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
oSIST prEN 14420-7:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 14420-7:2021
---------------------- Page: 2 ----------------------
oSIST prEN 14420-7:2021
DRAFT
EUROPEAN STANDARD
prEN 14420-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2021
ICS 23.040.70
English Version
Hose fittings with clamp units - Part 7: Cam locking
couplings
Raccords pour flexibles avec demi-coquille - Partie 7: Schlaucharmaturen mit Klemmfassungen - Teil 7:
Raccords à cames Hebelarmkupplungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 218.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14420-7:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
Contents Page
European Foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Requirements . 6
4.1 Construction . 6
4.2 Temperatures . 7
5 Survey . 7
6 Types of connection. 9
7 Designation. 11
8 Dimensions . 11
8.1 General . 11
8.2 Coupler types . 12
8.3 Cam arm (item No. 2) . 18
8.4 Pin (item No. 3) . 20
8.5 Ring (item No. 4) . 21
8.6 Main gasket (item No. 5) . 22
8.7 Thread gasket (item No. 6) . 22
8.8 Adapter types . 23
9 Materials . 27
9.1 General . 27
9.2 Coupler and adapter body . 28
9.3 Cam arm (item No. 2) . 29
9.4 Pin (item No. 3) . 29
9.5 Ring (item No. 4) . 29
9.6 Main gasket (item No. 5) . 29
9.7 Thread gasket (item No. 6) . 29
10 Marking . 30
11 Type testing and quality control . 30
Annex A (normative) Gauges for cam-locking couplings . 31
Bibliography . 33
2
---------------------- Page: 4 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
European Foreword
This document (prEN 14420-7:2021) has been prepared by Technical Committee CEN/TC 218 “Rubber
and plastics hoses and hose assemblies”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14420-7:2013.
In comparison to EN 14420-7:2013, the following changes have been made:
— In Clause 2, the Normative references have been updated.
— The Scope of the document has been changed.
EN 14420, Hose fittings with clamp units consists of the following parts:
— Part 1: Requirements, types of fixing and connection, designation and testing
— Part 2: Hose side parts of hose tail
— Part 3: Clamp units, bolted or pinned
— Part 4: Flange connections
— Part 5: Threaded connections
— Part 6: TW tank truck couplings
— Part 7: Cam locking couplings
— Part 8: Symmetrical half coupling (Guillemin system)
3
---------------------- Page: 5 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
Introduction
Cam locking couplings are manufactured worldwide according to the American “military specification”
MIL-C-27487. This American standard fixes the coupling side in a limited way, but not the connection
side. Other parts like levers, bolts, ring and gaskets are not standardized.
4
---------------------- Page: 6 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
1 Scope
This document specifies the design, materials, dimensions and marking requirements for cam locking
couplings that serve as the link between hoses and connections to transport liquids, solids and gases,
1
except liquid gas and steam. The couplings are capable of operating within the pressure range −0,8 bar
to 16 bar and in a working temperature range of −20 °C up to +65 °C. For all sizes of aluminium-cast-
material couplings and for all couplings size DN 100 the pressure range is from −0,8 bar to 10 bar.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 755-2, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical
properties
EN 1706, Aluminium and aluminium alloys — Castings — Chemical composition and mechanical properties
EN 1982, Copper and copper alloys — Ingots and castings
EN 10088-1, Stainless steels — Part 1: List of stainless steels
EN 10213, Steel castings for pressure purposes
EN 10226-1, Pipe threads where pressure tight joints are made on the threads — Part 1: Taper external
threads and parallel internal threads — Dimensions, tolerances and designation
EN 12420, Copper and copper alloys — Forgings
EN 14420-1:2013, Hose fittings with clamp units — Part 1: Requirements, types of fixing and connection,
designation and testing
EN 14420-2, Hose fittings with clamp units — Part 2: Hose side parts of hose tail
EN 14420-5, Hose fittings with clamp units — Part 5: Threaded connections
EN 22768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications (ISO 2768-1)
EN 22768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance
2
indications (ISO 2768-2)
EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation (ISO 228-1)
EN ISO 683-1, Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for
quenching and tempering (ISO 683-1)
EN ISO 8330:2014, Rubber and plastics hoses and hose assemblies — Vocabulary (ISO 8330:2014)
ISO 272, Fasteners — Hexagon products — Widths across flats
1
1 bar = 0,1 MPa.
2
EN 22768-2 has been withdrawn and replaced by EN ISO 22081.
5
---------------------- Page: 7 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 8330:2014 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
— IEC Electropedia: available athttps://www.electropedia.org/
3.1
DN
nominal size
alphanumeric designation of size for components of a pipework system, which is used for reference
purposes, comprised of the letters DN followed by a dimensionless whole number which is indirectly
related to the physical size, in millimetres, of the bore or outside diameter of the end connections
Note 1 to entry: The number following the letters DN does not represent a measurable value and should not be
used for calculation purposes except where specified in the relevant standard.
Note 2 to entry: In those standards which use the DN designation system, any relationship between DN and
component dimensions should be given, e.g. DN/OD or DN/ID.
[SOURCE: EN ISO 6708:1995, 2.1]
3.2
PN
alphanumeric designation used for reference purposes related to a combination of mechanical and
dimensional characteristics of a component of a hose fitting
Note 1 to entry: It comprises the letters PN followed by a dimensionless number.
Note 2 to entry: The number following the letters PN does not represent a measurable value and should not be
used for calculation purposes except where specified in the relevant standard.
3.3
main gasket
interface gasket between the male and female part of a coupling
3.4
thread gasket
flat faced gasket for threads according to EN ISO 228-1
4 Requirements
4.1 Construction
The curves of the lever and the adapters as well as the dimensions of the main gaskets shall be
harmonized such that twisting of the hose and vibrating during operation shall not lead to leakage. Cam
arms shall be manually operable.
Cam arms shall be suitable to operate without using tools.
For gauges for cam-locking couplings according to this document see Annex A.
NOTE If the requirements of this document are met, compatibility between couplers and adapters from
different manufacturers is ensured. Apart from gaskets, the interchangeability between spare parts from different
manufacturers cannot be ensured.
6
---------------------- Page: 8 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
4.2 Temperatures
Range of working temperatures of couplings equipped with nitrile butadiene rubber gasket
(NBR-gasket): −20 °C to +65 °C.
5 Survey
Figure 1 and Figure 2 show examples for cam-locking couplings. A parts list is given in Table 1.
NOTE Chain optional.
Figure 1 — Coupler type DF and adapter type DP (dust plug)
7
---------------------- Page: 9 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
NOTE Chain optional.
Figure 2 — Coupler type DC and adapter type AF
8
---------------------- Page: 10 ----------------------
oSIST prEN 14420-7:2021
prEN 14420-7:2021 (E)
Table 1 — Parts list
Item No. Number of Nomination
pieces
1 a 1 body with internal thread for coupler
1 b 1 with external thread
1 c 1 with welding connection
1 d 1 with hose nipple
1 e 1 cap
2 2 cam arms
3 2 pin
4 2 ring
5 1 main gasket
6 1 thread gasket for internal thread (see EN 14420-5)
a
7 1 At the discretion of the manufacturer
8 a 1 Adapter with internal thread
8 b 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.