SIST EN 12697-17:2004+A1:2007
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimen
Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimen
This European Standard describes a test method for determining the particle loss of porous asphalt mixtures. Particle loss is assessed by the loss of mass of porous asphalt samples after turns in the Los Angeles machine. This test enables the estimation of the abrasiveness of porous asphalt. The test applies to laboratory compacted porous asphalt mixtures the upper sieve size of which does not exceed 25 mm. It does not reflect the abrasive effect by studded tyres.
Asphalt - Prüfverfahren für Heißasphalt - Teil 17: Kornverlust von Probekörpern aus offenporigem Asphalt
Diese Europäische Norm beschreibt ein Prüfverfahren zur Bestimmung des Kornverlustes von offenporigem Asphalt. Der Kornverlust wird anhand des Massenverlustes von offenporigen Asphaltproben nach Beanspru¬chung im Los Angeles-Prüfgerät beurteilt. Diese Prüfung ermöglicht die Abschätzung der Abriebeigenschaften von offenporigem Asphalt. Die Prüfung gilt für im Labor verdichteten offenporigen Asphalt, dessen Größtkorn 25 mm nicht überschreitet. Sie spiegelt nicht die Abriebwirkung durch Spikereifen wider.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 17: Perte de matériau des éprouvettes d'enrobé drainant
La présente Norme européenne décrit une méthode de détermination de la perte de matériau (abrasion) des mélanges d’enrobé drainant. L’abrasion est évaluée par la perte de masse d’échantillons d’enrobé drainant a l’issue de passages dans la machine Los Angeles. Cet essai permet d’estimer le comportement a l’abrasion de l’enrobé drainant. L’essai s’applique a des mélanges d’enrobé drainant confectionnés en laboratoire, dont la dimension granulaire maximale ne dépasse pas 25 mm. Elle ne reflete pas l’abrasion due a des pneumatiques cloutés.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 17. del: Obraba delcev poroznih asfaltnih preskušancev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimenMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 17: Perte de matériau des éprouvettes d'enrobé drainantAsphalt - Prüfverfahren für Heißasphalt - Teil 17: Kornverlust von Probekörpern aus offenporigem AsphaltTa slovenski standard je istoveten z:EN 12697-17:2004+A1:2007SIST EN 12697-17:2004+A1:2007en,fr,de93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-17:2004+A1:200701-november-2007
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-17:2004+A1
July 2007 ICS 93.080.20 Supersedes EN 12697-17:2004English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimen
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 17: Perte de matériau des éprouvettes d'enrobé drainant
Asphalt - Prüfverfahren für Heißasphalt - Teil 17: Kornverlust von Probekörpern aus offenporigem Asphalt This European Standard was approved by CEN on 1 April 2004 and includes Amendment 1 approved by CEN on 16 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-17:2004+A1:2007: E
EN 12697-17:2004+A1:2007 (E) 2 Contents page Foreword.3 1 Scope.6 2 Normative references.6 3 Apparatus.6 4 Preparation of test specimen.6 5 Procedure.7 6 Calculation.7 7 Test report.8 8 Precision.8
EN 12697-17:2004+A1:2007 (E) 3 Foreword This document (EN 12697-17:2004+A1:2007) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2008 and conflicting national standards shall be withdrawn at the latest by January 2008. This document includes Amendment 1, approved by CEN on 2007-05-16. This document supersedes EN 12697-17:2004. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This European Standard is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of the reference density EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement
EN 12697-17:2004+A1:2007 (E) 4 EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or Marshall specimens EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures — Test method for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures —
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.