SIST EN ISO 340:2013
(Main)Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2013)
Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2013)
This International Standard specifies a method for assessing, on a small scale, the reaction of a conveyor belt to an ignition flame source. It is applicable to conveyor belts having a textile carcass as well as steel cord conveyor belts.
Fördergurte - Brandverhalten unter Laborbedingungen - Anforderungen und Prüfung (ISO 340:2013)
Diese Internationale Norm legt ein Prüfverfahren zur Bewertung eines Fördergurts im kleinen Maßstab fest, der einer Flamme als Zündquelle ausgesetzt ist. Dieses ist sowohl bei Textil- als auch bei Stahlseilfördergurten anwendbar.
Courroies transporteuses - Caractéristiques d'inflammabilité d'échelle de laboratoire - Exigences et méthode d'essai (ISO 340:2013)
L'ISO 340:2013 spécifie une méthode permettant d'évaluer, à petite échelle, la réaction d'une courroie transporteuse à une source d'allumage avec flamme. Elle est applicable aux courroies transporteuses à carcasse textile de même qu'à celles à câble acier.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Laboratorijska lestvica lastnosti gorljivosti (vnetljivosti) - Zahteve in preskusna metoda (ISO 340:2013)
Ta mednarodni standard določa metodo za ocenjevanje odziva trakov tračnih transporterjev v majhnem merilu na vir vžiga, tj. odprti plamen. Uporablja se za trake tračnih transporterjev, ki imajo trup iz tekstila, in transporterje, ki imajo železni kabel.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 340:2013
01-junij-2013
1DGRPHãþD
SIST EN ISO 340:2005
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY/DERUDWRULMVND
OHVWYLFDODVWQRVWLJRUOMLYRVWLYQHWOMLYRVWL=DKWHYHLQSUHVNXVQDPHWRGD,62Conveyor belts - Laboratory scale flammability characteristics - Requirements and test
method (ISO 340:2013)Courroies transporteuses - Caractéristiques d'inflammabilité d'échelle de laboratoire -
Exigences et méthode d'essai (ISO 340:2013)Ta slovenski standard je istoveten z: EN ISO 340:2013
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 340:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN ISO 340:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 340:2013
EUROPEAN STANDARD
EN ISO 340
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2013
ICS 13.220.40; 53.040.20 Supersedes EN ISO 340:2004
English Version
Conveyor belts - Laboratory scale flammability characteristics -
Requirements and test method (ISO 340:2013)
Courroies transporteuses - Caractéristiques
d'inflammabilité d'échelle de laboratoire - Exigences et
méthode d'essai (ISO 340:2013)
This European Standard was approved by CEN on 21 January 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 340:2013: E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
SIST EN ISO 340:2013
EN ISO 340:2013 (E)
Contents Page
Foreword ..............................................................................................................................................................3
---------------------- Page: 4 ----------------------SIST EN ISO 340:2013
EN ISO 340:2013 (E)
Foreword
This document (EN ISO 340:2013) has been prepared by Technical Committee ISO/TC 41 "Pulleys and belts
(including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the secretariat
of which is held by SNV.This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdrawn at
the latest by October 2013.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 340:2004.According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement noticeThe text of ISO 340:2013 has been approved by CEN as EN ISO 340:2013 without any modification.
---------------------- Page: 5 ----------------------SIST EN ISO 340:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 340:2013
INTERNATIONAL ISO
STANDARD 340
Fourth edition
2013-04-01
Conveyor belts — Laboratory scale
flammability characteristics —
Requirements and test method
Courroies transporteuses — Caractéristiques d’inflammabilité
d’échelle de laboratoire — Exigences et méthode d’essai
Reference number
ISO 340:2013(E)
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 340:2013
ISO 340:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 340:2013
ISO 340:2013(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Terms and definitions ..................................................................................................................................................................................... 1
4 Requirements .......................................................................................................................................................................................................... 1
4.1 Periods of afterflame (after removal of the burner) ............................................................................................... 1
4.2 Non-reappearance of flame (after applying a current of air) ......................................................................... 2
5 Test method ............................................................................................................................................................................................................... 2
5.1 Health and safety ................................................................................................................................................................................... 2
5.2 Principle ........................................................................................................................................................................................................ 2
5.3 Test pieces ................................................................................................................................................................................................... 2
5.4 Apparatus .................................................................................................................................................................................................... 3
5.5 Location of test ........................................................................................................................................................................................ 5
5.6 Conditioning of test pieces ........................................................................................................................................................... 5
5.7 Procedure .................................................................................................................................................................................................... 5
5.8 Expression of results .......................................................................................................................................................................... 5
6 Test report ................................................................................................................................................................................................................... 6
Bibliography ................................................................................................................................................................................................................................ 7
© ISO 2013 – All rights reserved iii---------------------- Page: 9 ----------------------
SIST EN ISO 340:2013
ISO 340:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 340 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.This fourth edition cancels and replaces the third edition (ISO 340:2004), which has been technically
revised. The word ‘combustion’ has been changed to ‘flame’.iv © ISO 2013 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.