SIST EN ISO 19085-17:2021
(Main)Woodworking machines - Safety requirements - Part 17: Edge-banding machines fed by chains (ISO 19085-17:2021)
Woodworking machines - Safety requirements - Part 17: Edge-banding machines fed by chains (ISO 19085-17:2021)
This document gives the safety requirements and measures for edge banding machines fed by chains or
belts, with manual loading and unloading and maximum workpiece height capacity of 100 mm, capable
of continuous production use, hereinafter referred as “machines”.
It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the
machines, when operated, adjusted and maintained as intended and under the conditions foreseen by
the manufacturer; reasonably foreseeable misuse has been considered too. Also, transport, assembly,
dismantling, disabling and scrapping phases are taken into account.
The machines are designed to process in one pass one end (single-end machine) or both ends (doubleend
machine) of panels of:
— materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2), even with a
core sheet of aluminium light alloy;
— gypsum plaster boards.
Edges to be applied by the machine can be made of:
— paper;
— melamine;
— plastic;
— composite materials;
— aluminium;
— light alloy;
— veneer;
— solid wood.
It is also applicable to machines fitted with one or more of the following devices/working units, whose
hazards have been dealt with:
— hot air banding unit;
— laser banding unit;
— infrared banding unit;
— dynamic processing units;
— sanding belt units;
— milling unit installed out of the integral enclosure at the panel side on single-end machines;
— milling unit installed out of the integral enclosure between machines halves of double-end machines;
— additional fixed or movable workpiece support along the feed;
— additional infeed workpiece support;
— additional outfeed workpiece support;
— in-feed device for transversal loading of panels in single-end machines;
— intermediate workpiece support in double-end machines;
— automatic panel returner in single-end machines;
— automatic tool changing;
— quick tool changing system;
— automatic multiple edges infeed device;
— workpiece heaters.
This document does not deal with any hazards relating to:
a) systems for loading and unloading of the workpiece to a single machine other than automatic panel
returner and infeed and outfeed workpiece supports (e.g. robots);
b) the combination of a single machine being used with other machines (as part of a line);
c) workpiece dividing unit installed out of the integral enclosure and/or whose tools protrude out of
the integral enclosure;
d) plasma banding unit.
It is not applicable to machines intended for use in potentially explosive atmosphere nor manufactured
before the date of its publication.
Holzbearbeitungsmaschinen - Sicherheit - Teil 17: Kantenanleimmaschinen mit Kettenbandvorschub (ISO 19085-17:2021)
Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen für Kantenanleimmaschinen mit Ketten- oder Bandvorschub mit Handbeschickung und Handentnahme und einer Werkstückhöhe von nicht mehr als 100 mm, die für den kontinuierlichen Einsatz in der Produktion geeignet sind, nachfolgend als „Maschinen“ bezeichnet, zur Verfügung.
Es behandelt alle im Anhang A aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorgesehenen Bedingungen verwendet, eingestellt und gewartet werden; vernünftigerweise vorhersehbare Fehlanwendung wurde ebenfalls berücksichtigt. Ferner werden die Phasen Transport, Montage, Demontage, Rückbau und Verschrottung berücksichtigt.
Die Maschinen sind konzipiert, um in einem Durchgang eine Seite (einseitige Maschine) oder beide Seiten (doppelseitige Maschine) von Platten aus
- Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz (siehe ISO 19085-1:2021, 3.2), auch solchen mit einem Kernblech aus Aluminium-Leichtmetall;
- Gipskarton
zu bearbeiten.
Das von der Maschine aufgebrachte Kantenmaterial kann aus
- Papier;
- Melamin;
- Kunststoff;
- Verbundwerkstoffen;
- Aluminium;
- Leichtmetall;
- Furnier;
- Massivholz
sein.
Es ist auch anwendbar für Maschinen, die mit einer oder mehreren der folgenden Vorrichtungen / Arbeitseinheiten ausgestattet sind, deren Gefährdungen behandelt wurden:
- Heißluft-Kantenverleimeinheit;
- Laser-Kantenverleimeinheit;
- Infrarot-Kantenverleimeinheit;
- dynamische Bearbeitungseinheit;
- Bandschleifeinheit;
- Fräseinheit, die bei einseitigen Maschinen werkstückseitig außerhalb der integrierten Kapselung installiert ist;
- Fräseinheit, die bei doppelseitigen Maschinen außerhalb der integrierten Kapselung zwischen den Maschinenhälften installiert ist;
- zusätzliche feststehende oder bewegliche Werkstückabstützung entlang des Vorschubs;
- zusätzliche Werkstückabstützung am Einlauf;
- zusätzliche Werkstückabstützung am Auslauf;
- Zuführvorrichtung zur Querbeschickung von Platten in einseitigen Maschinen;
- Werkstückzwischenabstützung in doppelseitigen Maschinen;
- automatische Plattenrückführeinrichtung in einseitigen Maschinen;
- automatischer Werkzeugwechsler;
- Schnellwechselsystem für Werkzeuge;
- automatische Mehrfach-Kantenzuführeinrichtung;
- Werkstückerhitzer.
Dieses Dokument behandelt keine Gefährdungen im Zusammenhang mit:
a) Systemen zum Be- und Entladen des Werkstücks auf eine einzige Maschine mit Ausnahme der automatischen Plattenrückführeinrichtung und der Werkstückabstützung am Ein und Auslauf (z. B. Roboter);
b) der Kombination einer einzelnen Maschine, die mit anderen Maschinen (als Teil einer Linie) verwendet wird;
c) Werkstücktrenneinheit, die außerhalb der integrierten Kapselung installiert ist und/oder dessen Werkzeuge aus der Teilkapselung herausragen;
d) Plasma-Kantenverleimeinheit.
Es ist nicht anwendbar für Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind oder vor dem Datum seiner Veröffentlichung hergestellt wurden.
Machines à bois - Sécurité - Partie 17: Machines à plaquer sur chant à alimentation par chaîne(s) (ISO 19085-17:2021)
Le présent document donne les exigences et mesures de sécurité pour les machines à plaquer sur chant à alimentation par chaînes ou courroies, avec chargement et déchargement manuel et une capacité de hauteur de pièce maximale de 100 mm, capables d’utilisation en production continue, ci-après désignées «machines».
Il traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, énumérés à l’Annexe A, applicables aux machines, lorsqu’elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant; une mauvaise utilisation raisonnablement prévisible a également été prise en compte. Les phases de transport, d’assemblage, de démontage, de mise hors service et de mise au rebut sont également prises en compte.
Les machines sont conçues pour usiner en une seule passe, une extrémité (machine simple) ou deux extrémités (machine double) de panneaux de:
— matériaux ayant des caractéristiques physiques similaires à celles du bois (voir l’ISO 19085‑1:2021, 3.2), même avec une âme centrale d’alliage léger d’aluminium;
— plaques de plâtre.
Les chants à appliquer par la machine peuvent être fabriqués en:
— papier;
— mélamine;
— plastique;
— matériaux composites;
— aluminium;
— alliage léger;
— placage;
— bois massif.
Il est également applicable aux machines équipées d’un ou plusieurs des dispositifs/unités de travail suivants, dont les phénomènes dangereux ont été traités:
— unité de plaquage par air chaud;
— unité de plaquage par laser;
— unité de plaquage par infrarouge;
— unités dynamiques;
— unités de ponçage à bande;
— unité de fraisage installée à l'extérieur de l'enceinte intégrée du côté du panneau sur les machines simples;
— unité de fraisage installée à l'extérieur de l'enceinte intégrée entre les demi-machines de machines doubles;
— support de pièce fixe ou mobile supplémentaire le long de l’avance;
— support supplémentaire d’entrée de pièce;
— support supplémentaire de sortie de pièce;
— dispositif d’entrée pour chargement transversal de panneaux dans les machines simples;
— support intermédiaire de pièce dans les machines doubles;
— dispositif de retour automatique de panneau dans les machines simples;
— changement automatique d’outil;
— système de changement rapide d’outil;
— dispositif d’entrée de chants multiples automatique;
— chauffe-pièces.
Le présent document ne traite pas des phénomènes dangereux relatifs à:
a) des systèmes pour le chargement et le déchargement de la pièce dans une machine simple autre qu’un dispositif de retour automatique de panneau et que des supports d’entrée et de sortie de pièce (par exemple, robots);
b) la combinaison d’une machine simple utilisée avec d'autres machines (comme partie d’une ligne);
c) une unité de division de pièce installée à l’extérieur de l’enceinte intégrée et/ou dont les outils dépassent de l’enceinte intégrée;
d) une unité de plaquage à plasma.
Il n’est pas applicable aux machines prévues pour une utilisation en atmosphère explosible, ni fabriquées avant la date de sa publication.
Lesnoobdelovalni stroji - Varnostne zahteve - 17. del: Stroji za lepljenje robnih trakov z verižnim dodajanjem (ISO 19085-17:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19085-17:2021
01-november-2021
Nadomešča:
SIST EN ISO 18217:2015
Lesnoobdelovalni stroji - Varnostne zahteve - 17. del: Stroji za lepljenje robnih
trakov z verižnim dodajanjem (ISO 19085-17:2021)
Woodworking machines - Safety requirements - Part 17: Edge-banding machines fed by
chains (ISO 19085-17:2021)
Holzbearbeitungsmaschinen - Sicherheit - Teil 17: Kantenanleimmaschinen mit
Kettenbandvorschub (ISO 19085-17:2021)
Machines à bois - Sécurité - Partie 17: Machines à plaquer sur chant à alimentation par
chaîne(s) (ISO 19085-17:2021)
Ta slovenski standard je istoveten z: EN ISO 19085-17:2021
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-17:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19085-17:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2021
EUROPÄISCHE NORM
ICS 79.120.10 Supersedes EN ISO 18217:2015
English Version
Woodworking machines - Safety - Part 17: Edge banding
machines fed by chains (ISO 19085-17:2021)
Machines à bois - Sécurité - Partie 17: Machines à Holzbearbeitungsmaschinen - Sicherheit - Teil 17:
plaquer sur chant à alimentation par chaînes (ISO Kantenanleimmaschinen mit Kettenbandvorschub (ISO
19085-17:2021) 19085-17:2021)
This European Standard was approved by CEN on 23 May 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-17:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this International Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17:2021 (E)
European foreword
This document (EN ISO 19085-17:2021) has been prepared by Technical Committee ISO/TC 39
"Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines -
Safety” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2022, and conflicting national standards shall
be withdrawn at the latest by January 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18217:2015.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN websites.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19085-17:2021 has been approved by CEN as EN ISO 19085-17:2021 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17:2021 (E)
Annex ZA
(informative)
Relationship between this International Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Requirements (ERs) of Clause(s)/subclause(s) of Remarks /
Directive 2006/42/EC this Notes
International Standard
1.1.2 Principles of safety integration
a) fitted for its function Clauses 4, 5, 6, 7
b) eliminate or reduce the risks, give measures, inform Clauses 4, 5, 6, 7
c) intended use and reasonably foreseeable misuse Clauses 4, 5, 6, 7
d) constraints in use 6.5, 7.3
e) equipment 5.1, 7.3
1.1.3 Materials and products 5.2, 6.3, 6.16, 6.17
1.1.4 Lighting 6.6, 7.3
1.1.5 Design of machinery to facilitate its handling 6.5
1.1.6 Ergonomics 6.5
1.1.7 Operating position 4.2
1.2.1 Safety and reliability of control systems 4.1, 6.7, 6.8
1.2.2 Control devices 4.2, 4.3, 4.4, 4.6, 4.7
1.2.3 Starting 4.3
1.2.4.1 Normal stop 4.4.1, 4.4.2
1.2.4.2 Operational stop 4.4.1, 4.4.3
1.2.4.3 Emergency stop 4.4.1, 4.4.4
1.2.5 Selection of control or operating mode 4.6
4
---------------------- Page: 6 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17:2021 (E)
1.2.6 Failure of the power supply 4.8, 6.7, 6.8
1.3.1 Risk of loss of stability 5.1, 7.3
1.3.2 Risk of break-up during operation 5.2, 7.3
1.3.3 Risks due to falling or ejected objects 5.2, 5.3, 5.5, 5.8, 5.9, 7.3
1.3.6 Risks relating to variations in the operating 4.7
conditions
1.3.7 Risks related to moving parts 5.6, 5.7, 7.3
1.3.8 Choice of protection against risks related to moving 5.5, 5.6
parts
1.4.1 General requirements 5.2, 5.5, 5.6, 5.9, 6.3
1.4.2.1 Fixed guards 5.5.1
1.4.2.2 Interlocking movable guards 5.5.2
1.4.3 Special requirements for protective devices 5.5.3, 5.5.5, 5.5.6, 5.5.7
1.5.1 Electricity supply 6.4, 6.13
1.5.2 Static electricity 6.11
1.5.3 Energy supply other than electricity 6.7, 6.8
1.5.4 Errors of fitting 6.12
1.5.6 Fire 6.1, 6.10
1.5.8 Noise 6.2
1.5.11 External radiation 6.9
1.5.12 Laser equipment 6.10
1.5.13 Emission of hazardous materials and substances 6.3
1.6.1 Machinery maintenance 6.14, 7.3
1.6.2 Access to operating position and servicing points 4.2, 6.14, 7.3
1.6.3 Isolation of energy sources 6.13, 7.3
1.6.4 Operator intervention 7.3
1.6.5 Cleaning of internal parts 6.14, 7.3
1.7.1.1 Information and information devices 6.10, 7.2
1.7.1.2 Warning devices 6.10, 7.1
1.7.2 Warning of residual risks 7.2
1.7.3 Marking of machinery 7.2
1.7.4 Instructions 6.10, 7.3, Annex F
2.3 Machinery for working wood and analogous materials
a) guiding 5.10
b) ejection 5.2, 5.3, 5.5, 5.9, 7.3
5
---------------------- Page: 7 ----------------------
SIST EN ISO 19085-17:2021
EN ISO 19085-17:2021 (E)
c) brake 4.5, 5.4
d) accidental tool contact 5.6.2, 5.6.6, 7.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this International
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
6
---------------------- Page: 8 ----------------------
SIST EN ISO 19085-17:2021
INTERNATIONAL ISO
STANDARD 19085-17
First edition
2021-05
Woodworking machines — Safety —
Part 17:
Edge banding machines fed by chains
Machines à bois — Sécurité —
Partie 17: Machines à plaquer sur chant à alimentation par chaînes
Reference number
ISO 19085-17:2021(E)
©
ISO 2021
---------------------- Page: 9 ----------------------
SIST EN ISO 19085-17:2021
ISO 19085-17:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 19085-17:2021
ISO 19085-17:2021(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Safety requirements and measures for controls . 9
4.1 Safety and reliability of control systems . 9
4.2 Control devices . 9
4.3 Start . 9
4.3.1 Direct start . 9
4.3.2 Start via control power-on .10
4.3.3 Integrated feed.10
4.4 Safe stops .10
4.4.1 General.10
4.4.2 Normal stop .10
4.4.3 Operational stop .11
4.4.4 Emergency stop .11
4.5 Braking function of tools .11
4.6 Mode selection .11
4.6.1 Units’ Manual adjustments mode (MODE 2) .12
4.6.2 Fine adjustment mode (MODE 3) .12
4.6.3 Feed chains greasing mode (MODE 4) .13
4.7 Tool speed changing .14
4.7.1 Speed changing by shifting the belts on the pulleys .14
4.7.2 Speed changing by incremental speed change motor .14
4.7.3 Infinitely variable speed by frequency inverter .14
4.8 Failure of any power supply .14
4.9 Manual reset control .14
4.10 Standstill detection and monitoring .14
4.11 Machine moving parts speed monitoring .14
4.12 Time delay .14
4.13 Teleservice .14
5 Safety requirements and measures for protection against mechanical hazards .14
5.1 Stability .14
5.2 Risk of break-up during operation .15
5.3 Tool and tool fixing design .15
5.3.1 General.15
5.3.2 Spindle locking .15
5.3.3 Circular saw blade fixing device .15
5.3.4 Flange dimension for circular saw blades .15
5.3.5 Spindle rings .15
5.4 Braking .16
5.4.1 Braking of tools .16
5.4.2 Maximum run-down time .16
5.4.3 Brake release .16
5.5 Safeguards .16
5.5.1 Fixed guards .16
5.5.2 Interlocking moveable guards .16
5.5.3 Hold-to-run control .17
5.5.4 Two-hand control .17
5.5.5 Electro-sensitive protective equipment (ESPE) .17
5.5.6 Pressure-sensitive protective equipment (PSPE).17
© ISO 2021 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 19085-17:2021
ISO 19085-17:2021(E)
5.5.7 Enabling control .17
5.6 Prevention of access to hazardous moving parts .17
5.6.1 Guarding of tools installed inside the integral enclosure .17
5.6.2 Guarding of external milling units .17
5.6.3 Guarding of sanding belts .18
5.6.4 Guarding of the edge banding zone .18
5.6.5 Access between machine halves on double-end machines .18
5.6.6 Access to hazard points through the slot between chain beam and top
pressure beam.19
5.6.7 Guarding of drives .20
5.6.8 Safeguarding of the feed mechanisms .20
5.6.9 Safeguarding of machine half movement on double-end machines .23
5.7 Impact hazard .26
5.8 Clamping devices .26
5.9 Measures against ejection .26
5.9.1 General.26
5.9.2 Guards materials and characteristics.27
5.9.3 Devices to minimize ejection of rigid edges .27
5.9.4 Height adjustments of feed mechanism .28
5.10 Workpiece supports and guides .28
5.10.1 General.28
5.10.2 Additional workpiece support at the outfeed .28
5.10.3 Transversal infeed device .29
5.10.4 Automatic panel returner.29
6 Safety requirements and measures for protection against other hazards .30
6.1 Fire . .30
6.2 Noise .31
6.2.1 Noise reduction at the design stage .31
6.2.2 Noise emission measurement and declaration .31
6.3 Emission of chips and dust .31
6.4 Electricity .31
6.5 Ergonomics and handling .31
6.6 Lighting .31
6.7 Pneumatics .31
6.8 Hydraulics .31
6.9 Electromagnetic compatibility .31
6.10 Laser .32
6.11 Static electricity .32
6.12 Errors of fitting .32
6.13 Isolation .32
6.14 Maintenance .32
6.15 Relevant but not significant hazards .32
6.16 Extreme temperatures .32
6.17 Substances .33
6.18 Artificial optical radiation .33
7 Information for use .33
7.1 Warning devices .33
7.2 Marking .33
7.2.1 General.33
7.2.2 Additional markings .33
7.3 Instruction handbook .34
7.3.1 General.
...
SLOVENSKI STANDARD
oSIST prEN ISO 19085-17:2019
01-november-2019
Lesnoobdelovalni stroji - Varnostne zahteve - 17. del: Stroji za lepljenje robnih
trakov z verižnim dodajanjem (ISO/DIS 19085-17:2019)
Woodworking machines - Safety requirements - Part 17: Edge-banding machines fed by
chains (ISO/DIS 19085-17:2019)
Holzbearbeitungsmaschinen - Sicherheit - Teil 17: Kantenanleimmaschinen mit
Kettenbandvorschub (ISO/DIS 19085-17:2019)
Machines à bois - Sécurité - Partie 17: Machines à plaquer sur chant à alimentation par
chaîne(s) (ISO/DIS 19085-17:2019)
Ta slovenski standard je istoveten z: prEN ISO 19085-17
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-17:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 19085-17:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 19085-17:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-17
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2019-09-10 2019-12-03
Woodworking machines — Safety —
Part 17:
Edge banding machines fed by chains
Machines à bois — Sécurité —
Partie 17: Machines à plaquer sur chant à alimentation par chaîne(s)
ICS: 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-17:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 List of significant hazards . 8
5 Safety requirements and measures for control . 9
5.1 Safety and reliability of control systems . 9
5.2 Control devices . 9
5.3 Start .10
5.3.1 Direct start .10
5.3.2 Start via control power-on .10
5.3.3 Integrated feed.10
5.4 Safe stops .11
5.4.1 General.11
5.4.2 Normal stop .11
5.4.3 Operational stop .11
5.4.4 Emergency stop .11
5.5 Braking function of tools .11
5.6 Mode selection .12
5.6.1 General.12
5.6.2 Manual adjustments during processing mode (MODE 2) .12
5.6.3 Fine adjustment mode (MODE 3) .12
5.6.4 Feed chains greasing mode (MODE 4) .13
5.7 Tool speed changing .14
5.7.1 Speed changing by shifting the belts on the pulleys .14
5.7.2 Speed changing by incremental speed change motor .14
5.7.3 Infinitely variable speed by frequency inverter .14
5.8 Failure of any power supply .14
5.9 Manual reset control .14
5.10 Standstill detection.14
5.11 Machine moving parts limited speed monitoring .14
5.12 Time delay .14
5.13 Tele-service .14
6 Safety requirements and measures for protection against mechanical hazards .14
6.1 Stability .14
6.2 Risk of break-up during operation .15
6.3 Tool holder and tool design.15
6.3.1 General.15
6.3.2 Spindle locking .15
6.3.3 Circular saw blade fixing devices .15
6.3.4 Flange dimensions for circular saw blades .15
6.3.5 Spindle rings .16
6.4 Braking .16
6.4.1 Braking of tools .16
6.4.2 Maximum run-down time .16
6.4.3 Brake release .16
6.5 Safeguards .16
6.5.1 Fixed guards .16
6.5.2 Interlocking moveable guards .16
6.5.3 Hold-to-run control .17
6.5.4 Two hand control .17
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
6.5.5 Electro-sensitive protective equipment (ESPE) .17
6.5.6 Pressure sensitive protective equipment (PSPE) .17
6.5.7 Enabling control .17
6.6 Prevention of access to hazardous moving parts .17
6.6.1 Guarding of tools installed inside the integral enclosure .17
6.6.2 Guarding of tools installed out of the integral enclosure .17
6.6.3 Guarding of sanding belts .18
6.6.4 Guarding of the edge banding zone .18
6.6.5 Access between machine halves on double end machines .18
6.6.6 Access to hazard points through the slot between chain beam and top
pressure beam.19
6.6.7 Guarding of drives .20
6.6.8 Safeguarding of the feed mechanisms .20
6.6.9 Safeguarding of machine half movement on double end machines .23
6.7 Impact hazard .26
6.8 Clamping devices .26
6.9 Measures against ejection .26
6.9.1 General.26
6.9.2 Guards materials and characteristics.27
6.9.3 Devices to minimize ejection of rigid edges .27
6.9.4 Height adjustments of feed mechanism .28
6.10 Workpiece support and guides .28
6.10.1 General.28
6.10.2 Additional out-feed workpiece support .28
6.10.3 Power-driven in-feed device for transversal loading of panels .29
6.10.4 Automatic panel returner.29
7 Safety requirements and measures for protection against other hazards .30
7.1 Fire . .30
7.2 Noise .30
7.2.1 Noise reduction at the design stage .30
7.2.2 Noise emission measurement .31
7.3 Emission of chips and dust .31
7.4 Electricity .31
7.5 Ergonomics and handling .31
7.6 Lighting .31
7.7 Pneumatics .31
7.8 Hydraulics .31
7.9 Electromagnetic compatibility .31
7.10 Laser .31
7.11 Static electricity .32
7.12 Errors of fitting .32
7.13 Isolation .32
7.14 Maintenance .32
7.15 Relevant but not significant hazards .32
7.16 Extreme temperatures .32
7.17 Substances .32
7.18 Artificial Optical Radiation .33
8 Information for use .33
8.1 Warning devices .33
8.2 Marking .33
8.2.1 General.33
8.2.2 Additional markings .33
8.3 Instruction handbook .34
8.3.1 General.34
8.3.2 Additional information .34
Annex A (informative) Performance levels required .36
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
Annex B (informative) Tests for braking function .38
Annex C (normative) Stability test .39
Annex D (normative) Impact test for guards .40
Annex E (normative) Noise test code .41
Annex ZA (informative) Relationship between this International Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered .46
Bibliography .48
© ISO 2019 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 4,
Woodworking machines.
This document is intended to be used in conjunction with ISO 19085-1:2020, which gives requirements
common to different machine types.
A list of all parts in the ISO 19085 series can be found on the ISO website.
vi © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 19085-17:2019
ISO/DIS 19085-17:2019(E)
Introduction
The ISO 19085 series of International Standards provides technical safety requirements for the
design and construction of woodworking machinery. It concerns designers, manufacturers, suppliers
and importers of the machines specified in the Scope. It also includes a list of informative items to be
provided to the user by the manufacturer.
This document is a type-C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope.
When requirements of this type-C standard are different from those which are stated in type-A or
type-B standards, the requirements of this type-C standard take precedence over the requirements of
the other standards for machines that have been designed and built according to the requirements of
this type-C standard.
The full set of requirements for a particular type of woodworking machine are those given in the part
of ISO 19085 applicable to that type, together with the relevant requirements from ISO 19085-1, to the
extent specified in the Scope of the applicable part of ISO 19085.
As far as possible, in parts of ISO 19085 other than ISO 19085-1, safety requirements are referenced
to the relevant sections of ISO 19085-1, to avoid repetition and reduce their length. The other parts
contain replacements and additions to the common requirements given in ISO 19085-1.
Thus, Clauses 5, 6, 7 and 8 with their subclauses and the annexes of this document can either
— confirm as a whole,
— confirm with additions,
— exclude in total, or
— replace with specific text
the corresponding subclauses or annexes of ISO 19085-1.
This interrelation is indicated in the first paragraph of each subclause or annex right after the title by
one of the following possible statements:
— “ISO/DIS 19085-1:2019, [subclause/Annex], applies”;
— “ISO/DIS 19085-1:2019, [subclause/Annex], applies with the following additions.” or
“ISO/DIS 19085-1:2019, [subclause/Annex], applies with the following additions, subdivided into
further specific subclauses.”;
— “ISO/DIS 19085-1:2019, [subclause/Annex], does not apply.”;
— “ISO/DIS 19085-1:2019, [subclause/Annex], is replaced by the following text.” or “ISO/DIS 19085-1:2019,
[subclause/Annex], is replaced by the following text, subdivided into further specific subclauses.”.
Specific subclauses and annexes in this document without correspondent in ISO/DIS 19085-1:2019 are
indicated by the introductory sentence: “Subclause/Annex specific to this document.”.
Clauses 1, 2 and 4 replace the correspondent clauses of ISO 19085-1, with no need for indication since
they are specific to each part of the series.
© ISO 2019 – All rights reserved vii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 19085-17:2019
---------------------- Page: 10 ----------------------
oSIST prEN ISO 19085-17:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 19085-17:2019(E)
Woodworking machines — Safety —
Part 17:
Edge banding machines fed by chains
1 Scope
This document gives the safety requirements and measures for edge banding machines fed by chains,
with manual loading and unloading and maximum workpiece height capacity of 100 mm, capable of
continuous production use, hereinafter referred as “machines”.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 releva
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.