F16.05 - Driven and Other Fasteners

SIGNIFICANCE AND USE
5.1 Nails, spikes, and dowel-type threaded fasteners are common mechanical fasteners in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded connections with these types of fasteners rely on a yield theory to establish the nominal resistance. In order to develop the nominal resistance for laterally-loaded connections, the fastener bending yield strength, length, and diameter must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment and calculation of bending yield strength (Fyb) of nails, spikes, and dowel-type threaded fasteners (referred to collectively as fasteners) when subjected to static loading. Bending yield strength is used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 1: This test method is applicable in either inch-pounds F1575 or SI Units [F1575M]. Values stated in SI are a mathematical conversion of two significant digits and are shown in brackets [ ].  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Staples are mechanical fasteners used in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded staple connections use a yield theory to establish nominal resistance (Note 2). In order to develop nominal resistance for laterally-loaded stapled connections, the bending yield moment must be known.
Note 2: When used as a structural fastener in shear walls and diaphragms, staples are installed with the crown parallel to the long dimension of the framing member. The orientation of the staples for this bending yield moment test represents the bending yield moment applicable for this intended use).
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of staples when subjected to static loading. Although intended for flat crown staples identified in Specification F1667/F1667M, this procedure is also applicable for staples with round wire. These staples are used in engineered wood building connection applications for which required connection capacities are specified by the designer.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 1: This test method is applicable in either inch-pounds F3359 or SI Units [F3359M]. Values stated in SI are a mathematical conversion and are shown in brackets [ ].  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–63.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 This specification is applicable in either inch-pounds (F1667) or SI units [F1667M]. Values stated in SI are a mathematical conversion to two significant digits and are shown in brackets [ ].  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 When specified, the tests selected for application shall be performed to assure conformance with requirements stipulated in the product specification.
SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D1761.  
1.2 The tests described are as follows:    
Section    
Dimensional tests  
5  
Tension test  
6  
Conventional bend test  
7  
Impact bend test  
8  
Rockwell hardness test  
9  
Coating weight test  
10  
Coating adherence test for zinc-coated nails  
11  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 1: This test method is applicable in either inch-pounds F1575 or SI Units [F1575M]. Values stated in SI are a mathematical conversion of two significant digits and are shown in brackets [ ].  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–64.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Staples are mechanical fasteners used in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded staple connections use a yield theory to establish nominal resistance (Note 1). In order to develop nominal resistance for laterally-loaded stapled connections, the bending yield moment must be known.
Note 1: When used as a structural fastener in shear walls and diaphragms, staples are installed with the crown parallel to the long dimension of the framing member. The orientation of the staples for this bending yield moment test represents the bending yield moment applicable for this intended use).
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of staples when subjected to static loading. Although intended for flat crown staples identified in Specification F1667, this procedure is also applicable for staples with round wire. These staples are used in engineered wood building connection applications for which required connection capacities are specified by the designer.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Staples are mechanical fasteners used in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded staple connections use a yield theory to establish nominal resistance (Note 1). In order to develop nominal resistance for laterally-loaded stapled connections, the bending yield moment must be known.
Note 1: When used as a structural fastener in shear walls and diaphragms, staples are installed with the crown parallel to the long dimension of the framing member. The orientation of the staples for this bending yield moment test represents the bending yield moment applicable for this intended use).
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of staples when subjected to static loading. Although intended for flat crown staples identified in Specification F1667, this procedure is also applicable for staples with round wire. These staples are used in engineered wood building connection applications for which required connection capacities are specified by the designer.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 When specified, the tests selected for application shall be performed to assure conformance with requirements stipulated in the product specification.
SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D1761.  
1.2 The tests described are as follows:    
Section    
Dimensional tests  
5  
Tension test  
6  
Conventional bend test  
7  
Impact bend test  
8  
Rockwell hardness test  
9  
Coating weight test  
10  
Coating adherence test for zinc-coated nails  
11  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.  
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.               (A) All dimensions given in inches.          (A) All dimensions are given in inches.     (A) All dimension are given in inches.   (A) All dimensions are given in inches.   (A) All dimensions are given in inches.(B) Dashes (—) indicate that the fastener size is not a standard size.
† Editorially corrected in March 2012.  (A) All dimensions are given in inches.(B) Dashes (—) indicate that the fastener size is not a standard size.            
   L  =  length, in.,   H  =   head diameter, in.,   TL  =  length of threaded shank, in.,   max  =  maximum acceptable value (not subject to tolerances),   min  =   minimum acceptable value (not subject to tolerances),    D  =  shank diameter, in.,   T1  =   crest diameter, in., and   P  =  pitch, or spacing of threads, in.  (A) All dimensions are given in inches.(B) Root diameter is a calculated value and is not specified as a dimension to be measured.  
   L  =  length, in.,   H  =  head diameter, in.,   TL  =  length of threaded shank, in.,   max  =  maximum acceptable value (not subject to tolerances),   min  =  minimum acceptable value (not subject to tolerances),    D  =  shank diameter, in.,   T1  =  crest diameter, in., and   P  =  pitch, or spacing of threads, in.  (A) All dimensions are given in inches.(B) Nails shall comply with the supplementary requirements of S1 and Table S1.1.(C) Nails identified as “F1667 NLRSRS” must meet all applicable requirements of F1667 for the specified roof sheathing ring shank nail.(D) Individual rings shall be approximately frustrums, circular in transverse cross section, axially symmetric, and formed on the nail axis such that the minor diameter is closer to the nail point and the major diameter is closer to the nail head. The thread shall be continuous over the minimum thread length, TLmin.           (A) All dimensions are given in inches.        
Dimensions and Tolerances for Gages of Flat Top Crown Staples  
10 Gage  
12 Gage  
14 Gage  
15 Gage  
16 Gage  
18 Gage  
T  
W  
T  
W  
T  
W  
T  
W  
T  
W  
T  
W  
Nominal  
.1250  
.1400  
.0935  
.1120  
.0735  
.0855  
.0673  
.073  
.0563  
.064  
.038  
.050  
Maximum  
.1290  
.1440  
.0975  
.1160  
.0775  
.0895  
.0731  
.076  
.0626  
.068  
.0415  
.0532  
Minimum  
.1210  
.1360  
.0895  
.1080  
.0695  
.0815  
.0615  
.070  
.0500  
.060  
.0345  
.0468  
Tolerance  
±  
.0040  
.0040  
.0040  
.0040  
.0040  
.0040  
.0058  
.003  
.0063  
.004  
.0035  
.0032(A) All dimensions are given in inches.        
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, p...

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. TABLE 1 Classification and Identification Index    
Type  
Style  
Style Identification  
Table    
I—Nails (NL)  
1.  
Brads  
BR  
3    
2.  
Barrel  
BL  
4    
3.  
Boat  
BTH/BTL  
5    
4.  
Box A  
BXA  
6    
Box B  
BXB  
7    
5.  
Broom  
BM  
8    
6.  
Casing  
CN  
9    
7.  
Cooler  
CL  
10    
8.  
Sinker  
SK  
11    
9.  
Corker  
CK  
12    
10.  
Common  
CMA  
13    
Common  
CMC  
14    
Common  
CMS  
15    
Common  
CMM  
16    
11.  
Concrete  
CTS/CTM  
17    
12.  
Double-headed  
DH  
18    
13.  
Fine  
FN  
19    
14.  
Finishing  
FH  
20    
15.  
Flooring  
FL  
21    
16.  
Lath  
LHF  
22    
Lath  
LHH  
23    
17.  
Masonry  
MR/MRH  
24    
18.  
Pallet  
PL  
25    
19.  
Gypsum wallboard  
GWS  
26    
Gypsum wallboard  
GWM  
27    
20.  
Roofing  
RFA  
28    
Roofing  
RFS  
29    
Roofing  
RFC  
30    
Roofing  
RFL  
31    
Roofing  
RFR  
32    
Roofing  
RFD  
33    
Roofing  
RFNS/RFND  
34    
21.  
Shingle  
SHAD/SHAS  
35    
Shingle  
SHSS/SHNSB  
36    
22.  
Siding  
SDF/SDC/SDK  
37    
23.  
Slating  
SLA/SLC/SLS  
38    
24.  
Rubber heel  
RH  
39    
25.  
Underlayment  
UL  
40    
26.  
Square-barbed  
SB  
41    
27.  
Masonry drive  
MD  
42    
28.  
Escutcheon  
ES  
43    
29.  
Glulam rivet  
GR  
44    
30.  
Post frame  
PF  
45  
II—Cut nails (CN)  
1.  
Common  
CM  
46    
2.  
Basket  
BK  
47    
3.  
Clout  
CL  
48    
4.  
Trunk  
TR  
49    
5.  
Cobblers  
CB  
50    
6.  
Extra-iron clinching  
EC  
51    
7.  
Hob  
HB  
52    
III—Spikes (SP)  
1.  
Common  
CM  
53    
2.  
Gutter  
GRF/GRO  
54    
3.  
Round  
RDC/RDF  
55    
4.  
Barge and boat  
BB  
56  
IV—Staples (ST)  
1.  
Fence  
FN  
57    
2.  
Poultry netting  
PN  
58    
3.  
Flat top crown  
FC  
59    
Flat top crown  
FCC  
60  
4.  
Round or V crown  
RC  
61    
5.  
Preformed  
PC  
62    
6.  
Electrical  
RE  
63    
7.  
Preformed hoop  
PH  
64    
8.  
Cap  
STC  
65
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.TABLE 2 Bend Angles for Fasteners Using the Test Methods F680 Bend Test    
Fastener Material  
Bend Angle, °    
1.  
Steel wire: (low-carbon, medium-low
carbon, medium-carbon) (unhardened)  
180    
2.  
Stainless steel wire  
180    
3.  
Hardened steel fasteners  
20    
4.  
Sheet steel for cut nails, Type II,
and cut spikes, Type III  
9...

SIGNIFICANCE AND USE
5.1 Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 When specified, the tests selected for application shall be performed to assure conformance with requirements stipulated in the product specification.
SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D1761.  
1.2 The tests described are as follows:    
Section    
Dimensional tests  
5  
Tension test  
6  
Conventional bend test  
7  
Impact bend test  
8  
Rockwell hardness test  
9  
Coating weight test  
10  
Coating adherence test for zinc-coated nails  
11  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
0

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-67.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-67.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
TABLE 1 Classification and Identification Index   Type Style Style Identification  Table   INails (NL)  1. Brads BR  3   2. Barrel BL  4   3. Boat BTH/BTL  5   4. Box A BXA  6  Box B  BXB  7   5. Broom BM  8   6. Casing CN  9   7. Cooler CL 10   8. Sinker SK 11   9. Corker CK 12   10. Common CMA 13  Common  CMC 14  Common  CMS 15  Common  CMM 16   11. Concrete CTS/CTM 17   12. Double-headed DH 18   13. Fine FN 19   14. Finishing FH 20   15. Flooring FL 21   16. Lath LHF 22  Lath  LHH 23   17. Masonry MR/MRH 24   18. Pallet PL 25   19. Gypsum wallboard GWS  26  Gypsum wallboard GWM 27   20. Roofing RFA 28  Roofing  RFS 29  Roofing  RFC 30  Roofing  RFL 31  Roofing  RFR 32  Roofing  RFD 33  Roofing  RFNS/RFND 34   21. Shingle SHAD/SHAS 35  Shingle  SHSS/SHNSB 36   22. Siding SDF/SDC/SDK 37   23. Slating SLA/SLC/SLS 38   24. Rubber heel RH 39   25. Underlayment UL 40   26. Square-barbed SB 41   27. Masonry drive MD 42   28. Escutcheon ES 43   29. Glulam rivet GR 44  30.Post framePF45 IICut nails (CN)  1.  Common CM 46   2. Basket BK 47   3. Clout CL 48   4. Trunk TR 49   5. Cobblers CB 50   6. Extra-iron clinching EC  51   7. Hob HB 52  IIISpikes (SP)  1.  Common CM 53   2. Gutter GRF/GRO 54   3. Round RDC/RDF 55   4. Barge and boat BB  56 IVStaples (ST)  1.  Fence FN 57   2. Poultry netting PN  58   3. Flat top crown FC  59  Flat top crown FCC 60  4. Round or V crown RC  61   5. Preformed PC 62   6. Electrical RE 63   7. Preformed hoop PH  64   8. CapSTC 65
TABLE 2 Bend Angles for Fasteners Using the Test Methods F680 Bend Test   Fastener Material Bend Angle, °   1.  Steel wire: (low-carbon, medium-low
carbon, medium-carbon) (unhardened) 180  2.  Stainless steel wire 180  3.  Hardened steel fasteners  20  4.  Sheet steel for cut nails, Type II,
and cut spikes, Type III  90  5.  Copper (min 98 %) 180  6.  Copper clad wire (min 20 %)  180  7.  Aluminum alloy wire  90  8.  Brass wire 180  
TABLE 3 Type I, Style 1BradsA
Note—Steel wire, brad head, diamond point, round smooth shank, bright finish. When specified, brads shall have a modified brad head with a blunt or chiseled point for use with mechanical drivers.  
TABLE 4 Type I, Style 2Barrel Nail...

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.  
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-67.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in tables 3-64.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
When specified, the tests selected for application shall be performed to assure conformance with requirements stipulated in the product specification.
SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D 1761.  
1.2 The tests described are as follows:
  Section  Dimensional tests5 Tension test6 Conventional bend test7 Impact bend test8 Rockwell hardness test9 Coating weight test10 Coating adherence test for zinc-coated nails11  
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.
Note 1—Fastener ductility information is presented in Table 2 and dimensional information in tables 3-64.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.
Note1—Fastener ductility information is presented in and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known.
SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Fastener ductility information is presented in and dimensional information in Table 1.
Note—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and may be positioned for striking by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Fastener ductility information is presented in and dimensional information in Table 1.
Note—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and may be positioned for striking by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Fastener ductility information is presented in and dimensional information in Table 1.
Note—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and may be positioned for striking by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Fastener ductility information is presented in and dimensional information in Table 1.
Note—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and may be positioned for striking by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Fastener ductility information is presented in and dimensional information in Table 1.
Note—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-63.
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and may be positioned for striking by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D1761.  
1.2 The tests described are as follows:  Section Dimensional tests 5 Tension test 6 Conventional bend test 7 Impact bend test 8 Rockwell hardness test 9 Coating weight test 10 Coating adherence test for zinc-coated nails 11
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information purposes only.

SIGNIFICANCE AND USE
When specified, the tests selected for application shall be performed to assure conformance with requirements stipulated in the product specification.
SCOPE
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D 1761.
1.2 The tests described are as follows:Section Dimensional tests5Tension test6Conventional bend test7Impact bend test8Rockwell hardness test9Coating weight test10Coating adherence test for zinc-coated nails11
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information purposes only.

SCOPE
0
WITHDRAWN RATIONALE
The terms included in these definitions are listed in alphabetical order to facilitate quick reference. They are intended to apply to collated and cohered nails, staples, and pins driven by strike, pneumatic, electric, manual, and spring tools. Omitted from consideration are terms relating to the testing and the performance of fasteners, that is, their drivability, withdrawal resistance, pull-through resistance, lateral load transmission, creep, protrusion resistance, splitting, and methods of use, such as face, toe, side, and end-nailing, spacing, loading conditions, etc.
Formerly under the jurisdiction of Committee F16 on Fasteners, this terminology standard was withdrawn in March 2017. This standard is being withdrawn with no replacement because most of the terminology in the standard is no longer relevant.