CLC/SR 23 - Electrical accessories
Electrical accessories
General Information
IEC 61535:2023 is available as IEC 61535:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61535:2023 applies to two-wire, up to five-wire installation couplers, with or without earthing contact, if provided, with a rated voltage up to and including 500 V AC or 500 V DC and a rated connecting capacity up to and including 10 mm2 and a rated current not exceeding 32 A for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) inclusion of a definition for "live part" based on IEC 61140; b) additional optional cross medial documentation, e.g. marking with QR-Code; c) corrections on the consistent use of the expressions "earth", "earthing contact", "earthing circuit" and "protective earth(ing)" throughout the document; d) addition of missing compliance provisions to 13.3; e) update of Figure D.1 of Annex D; f) inclusion of new Annex F for cold climate requirements.
- Standard61 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61535:2019 is available as IEC 61535:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61535:2019 applies to two-wire, up to five-wire installation couplers, including earth, if provided, with a rated voltage up to and including 500 V AC or DC and a rated connecting capacity up to and including 10 mm2 for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This second edition cancels and replaces the first edition published in 2009 and Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - enlargement of the scope to DC application; - addition of further requirements as regards DC application (marking, etc.), no additional test procedures were deemed necessary; however some modifications were necessary in the normative text; - changes and enhancement of the field of application of installation couplers into outdoor applications; - addition of a suitable temperature range; - updating of the list of normative references, modified to undated references, where possible.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63172:2020 provides a methodology for determining the energy efficiency class of electrical accessories, to enable the system designer to determine the most efficient components for an electrical installation, also considering all functionalities. This methodology is based on the energy consumption, taking into account the individual functions of the accessory. The energy efficiency class approach contributes to the overall reduction of the energy consumption of an electrical installation.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment9 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part of an equipment or of a component, or as a separate entity. This standard establishes uniform requirements for the dimensions, performance characteristics and test program. The connected electrical copper conductors shall be flexible or rigid stranded, having a cross-sectional area up to and including 6 mm2 or rigid solid having a cross-sectional area up to and including 2,5 mm2. This standard shall not be used for connecting aluminum conductors. The rated voltage shall not exceed 1 000 V a.c. with a frequency up to and including 1 000 Hz, and 1 500 V d.c., and having the temperature limits applicable to materials used within this standard. This second edition cancels and replaces the first edition published in 1993 and constitutes a merge between the first edition of IEC 61210 published by SC23F and IEC 60760 published in 1989 by SC48B. This second edition does not introduce major technical modifications.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard applies to sound signalling devices with integral enclosures or to sound signalling devices intended to be fitted into or supplied with enclosures according to IEC 60670 intended for household and similar purposes with rated voltages greater than 50 V a.c. or 75 V d.c. and not exceeding 250 V a.c. or 250 V d.c., and with rated power inputs not exceeding 100 VA. This standard applies to fixed, portable and plug-in devices for indoor or outdoor use.
- Standard81 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard applies to twist-on connecting devices for connecting two or more unprepared rigid and/or flexible copper conductors having a cross-sectional area of 0,5 mm2 up to and including 16 mm2 and complying with EN 60228, the total cross-sectional area of the connected conductors not exceeding 35 mm2. It covers low voltage circuits up to 1 000 V a.c. and 1 500 V d.c. where electrical energy is utilized for household and similar purposes. It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
Supplement to EN 60998-1. Applies to connecting devices primarily suitable for connecting insulated unprepared conductors. This publication supersedes EN 60685-2-3 (1983). Has the status of a group safety publication in accordance with IEC Guide 104.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
Supplement to EN 60998-1. Applies to connecting devices primarily suitable for connecting unprepared conductors. This publication supersedes EN 60685-2-1 (1980). Has the status of a group safety publication in accordance with IEC Guide 104.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
Applies to connecting devices with screw-type clamping units primarily suitable for connecting unprepared conductors. This publication supersedes EN 685-2-2 (1983). Has the status of a group safety publication in accordance with IEC Guide 104.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 60998 applies to connecting devices as separate entities for the connection of two or more electrical copper conductors (complying with EN 60228 or EN 60344) rigid (solid or stranded) or flexible, having a cross-sectional area of 0,2 mm2 up to and including 35 mm2 and equivalent AWG conductors with a rated voltage not exceeding 1 000 V a.c. up to and including 1 000 Hz and 1 500 V d.c. where electrical energy is used for house-hold and similar purposes. This standard constitutes Part 1 of the EN 60998 series, published under the general title Connecting devices for low-voltage circuits for household and similar purposes. This series consists of this Part 1, devoted to general requirements, and various Parts 2, devoted to particular requirements. This second edition cancels and replaces the first edition published in 1990 and constitutes a technical revision. It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
Applies to screw-type and screwless-type clamping units for connecting devices, either as separate entities or as integral parts of equipment, for the connection of electrical copper conductors (complying with IEC 228), rigid (solid or stranded) and/or flexible, having a cross-sectional area of 0.5 mm2 up to and including 35 mm2 and equivalent AWG sizes with a rated voltage not exceeding 1 000 V a.c. with a frequency up to and including 1 000 Hz, and 1 500 V d.c. Has the status of a group safety publication in accordance with IEC Guide 104.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This standard applies to flat non-rewirable two-pole plugs without earthing contact with a rated voltage of 250 V a.c. and a rated current of 2,5 A. They are supplied with a cord, for the purposes, and having no special protection against ingress or water are intended for indoor use. Plugs complying with this standard are suitable for use at ambient temperatures not normally exceeding 25°C but occasionally reaching 35°C. Plug portions of adapters or equipment, such as razors or lamps with rechargeable batteries, plug-in transformers, etc., shall comply with the requirements of this standard as far as they reasonably apply.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
2012-05-24: Publication editing allocated to cpalagi@cencenelec.eu
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61535:2009 applies to two up to five wire installation couplers including earth, if provided, with a rated voltage up to and including 500 V a.c. and a rated connecting capacity up to and including 10 mm² for permanent connection in indoor electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this standard.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day