ASTM D130-04
(Test Method)Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
SCOPE
1.1 This test method covers the determination of the corrosiveness to copper of aviation gasoline, aviation turbine fuel, automotive gasoline, cleaners (Stoddard) solvent, kerosine, diesel fuel, distillate fuel oil, lubricating oil, and natural gasoline or other hydrocarbons having a vapor pressure no greater than 124 kPa (18 psi) at 37.8°C. (Warning—Some products, particularly natural gasoline, may have a much higher vapor pressure than would normally be characteristic of automotive or aviation gasolines. For this reason, exercise extreme caution to ensure that the pressure vessel used in this test method and containing natural gasoline or other products of high vapor pressure is not placed in the 100°C (212°F) bath. Samples having vapor pressures in excess of 124 kPa (18 psi) may develop sufficient pressures at 100°C to rupture the pressure vessel. For any sample having a vapor pressure above 124 kPa (18 psi), use Test Method D 1838.)
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. For specific warning statements, see 1.1, 6.1, and Annex A2.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 130 – 04 Federation of Societies for
Paint Technology Standard No. Dt-28-65
British Standard 4351
Designation: 154/93
Standard Test Method for
Corrosiveness to Copper from Petroleum Products by
1
Copper Strip Test
This standard is issued under the fixed designation D 130; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 This test method covers the determination of the corro- 2.1 ASTM Standards:
siveness to copper of aviation gasoline, aviation turbine fuel, D 396 Specification for Fuel Oils
automotive gasoline, cleaners (Stoddard) solvent, kerosine, D 975 Specification for Diesel Fuel Oils
diesel fuel, distillate fuel oil, lubricating oil, and natural D 1655 Specification for Aviation Turbine Fuels
gasoline or other hydrocarbons having a vapor pressure no D 1838 Test Method for Copper Strip Corrosion by Lique-
greater than 124 kPa (18 psi) at 37.8°C. (Warning—Some fied Petroleum (LP) Gases
products, particularly natural gasoline, may have a much D 4057 Practice for Manual Sampling of Petroleum and
higher vapor pressure than would normally be characteristic of Petroleum Products
automotive or aviation gasolines. For this reason, exercise D 4177 Practice for Automatic Sampling of Petroleum and
extreme caution to ensure that the pressure vessel used in this Petroleum Products
test method and containing natural gasoline or other products E 1 Specification forASTM Liquid-in-Glass Thermometers
of high vapor pressure is not placed in the 100°C (212°F) bath. 2.2 ASTM Adjuncts:
3
Samples having vapor pressures in excess of 124 kPa (18 psi) ASTM Copper Strip Corrosion Standard
may develop sufficient pressures at 100°C to rupture the
3. Summary of Test Method
pressure vessel. For any sample having a vapor pressure above
124 kPa (18 psi), use Test Method D 1838.) 3.1 Apolishedcopperstripisimmersedinaspecificvolume
of the sample being tested and heated under conditions of
1.2 The values stated in SI units are to be regarded as the
standard. The values in parentheses are for information only. temperature and time that are specific to the class of material
being tested. At the end of the heating period, the copper strip
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the is removed, washed and the color and tarnish level assessed
against the ASTM Copper Strip Corrosion Standard.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
4. Significance and Use
bility of regulatory requirements prior to use. For specific
4.1 Crude petroleum contains sulfur compounds, most of
warning statements, see 1.1, 6.1, and Annex A2.
which are removed during refining. However, of the sulfur
compoundsremaininginthepetroleumproduct,somecanhave
1
This test method is under the jurisdiction of ASTM Committee D02 on a corroding action on various metals and this corrosivity is not
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
D02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.
2
Current edition approved May 1, 2004. Published June 2004. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1922, replacing former D 89. Last previous edition approved in 2000 as contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
e1
D 130–94 (2000) . Standards volume information, refer to the standard’s Document Summary page on
In the IP, this test method is under the jurisdiction of the Standardization the ASTM website.
3
Committee. It is issued under the fixed designation IP 154. The final number Available from ASTM International Headquarters. Order Adjunct No.
indicates the year of last revision. ADJD0130. Names of suppliers in the United Kingdom can be obtained from
This test method has been approved by the sponsoring committees and accepted Energy Institute, 61 New Cavendish St., London, WIG 7AR, U.K. Two master
by the cooperating societies in accordance with established procedures. standards are held by the IP for reference.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D130–04
necessarily related directly to the total sulfur content. The
effect can vary according to the chemical types of sulfur
compounds present.The copper
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.