ASTM C1093-15ae1
(Practice)Standard Practice for Accreditation of Testing Agencies for Masonry
Standard Practice for Accreditation of Testing Agencies for Masonry
SIGNIFICANCE AND USE
4.1 This practice provides the basic minimum criteria for use in evaluating the qualifications of testing agencies for masonry materials. The criteria may be supplemented by more specific criteria and requirements. It can be used as a guide for internal audits by individual users.
4.2 The intent of this practice is to provide a consensus basis for evaluating a testing agency, with respect to that agency's capability to objectively and competently provide the specific services needed by the user.
4.3 This practice may be used as a basis for accreditation.
SCOPE
1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system, and it establishes minimum qualifications for agencies engaged in the testing of masonry materials.
1.2 Criteria are provided for evaluating the capability of an agency to properly perform designated tests on masonry materials, and for establishing guidelines pertaining to an agency's organization, personnel, facilities, and quality system. This practice may be supplemented by more specific criteria and requirements for particular projects.
1.3 This practice can be used as a basis to evaluate testing agencies, and it is intended for use for the qualifying or accrediting of testing agencies, or both, public or private, engaged in the testing of masonry materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: C1093 − 15a
Standard Practice for
1
Accreditation of Testing Agencies for Masonry
This standard is issued under the fixed designation C1093; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected 7.2 in July 2016.
1. Scope* C136 Test Method for Sieve Analysis of Fine and Coarse
Aggregates
1.1 This practice covers the minimum requirements for
C140 Test Methods for Sampling and Testing Concrete
laboratorypersonnel,forestablishingandmaintainingaquality
Masonry Units and Related Units
system, and it establishes minimum qualifications for agencies
C143/C143M Test Method for Slump of Hydraulic-Cement
engaged in the testing of masonry materials.
Concrete
1.2 Criteria are provided for evaluating the capability of an
C173/C173M Test Method forAir Content of Freshly Mixed
agency to properly perform designated tests on masonry
Concrete by the Volumetric Method
materials, and for establishing guidelines pertaining to an
C185 Test Method for Air Content of Hydraulic Cement
agency’sorganization,personnel,facilities,andqualitysystem.
Mortar
This practice may be supplemented by more specific criteria
C230/C230M Specification for Flow Table for Use in Tests
and requirements for particular projects.
of Hydraulic Cement
1.3 This practice can be used as a basis to evaluate testing C231 Test Method for Air Content of Freshly Mixed Con-
crete by the Pressure Method
agencies, and it is intended for use for the qualifying or
accrediting of testing agencies, or both, public or private, C270 Specification for Mortar for Unit Masonry
C305 Practice for Mechanical Mixing of Hydraulic Cement
engaged in the testing of masonry materials.
Pastes and Mortars of Plastic Consistency
1.4 This standard does not purport to address all of the
C470/C470M Specification for Molds for Forming Concrete
safety concerns, if any, associated with its use. It is the
Test Cylinders Vertically
responsibility of the user of this standard to establish appro-
C780 Test Method for Preconstruction and Construction
priate safety and health practices and determine the applica-
Evaluation of Mortars for Plain and Reinforced Unit
bility of regulatory limitations prior to use.
Masonry
C1072 Test Methods for Measurement of Masonry Flexural
2. Referenced Documents
Bond Strength
2
2.1 ASTM Standards:
C1232 Terminology of Masonry
C67 Test Methods for Sampling and Testing Brick and
C1506 Test Method for Water Retention of Hydraulic
Structural Clay Tile
Cement-Based Mortars and Plasters
C109/C109M Test Method for Compressive Strength of
E4 Practices for Force Verification of Testing Machines
Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube
E11 Specification for Woven Wire Test Sieve Cloth and Test
Specimens)
Sieves
C117 Test Method for Materials Finer than 75-µm (No. 200)
Sieve in Mineral Aggregates by Washing
3. Terminology
3.1 Definitions:
3.1.1 quality system—the organizational structure,
1
This practice is under the jurisdiction of ASTM Committee C15 on Manufac-
responsibilities, procedures, processes, capabilities, and re-
tured Masonry Units and is the direct responsibility of Subcommittee C15.07 on
sources for implementing quality management.
Standards for Laboratory Accreditation.
Current edition approved Dec. 15, 2015. Published January 2016. Originally
3.2 Definitions of Terms Specific to This Standard:
approved in 1988. Last previous edition approved in 2015 as C1093 – 15. DOI:
3.2.1 agency—the organization engaged to test masonry
10.1520/C1093-15AE01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
materials as required by a specification or contract.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3.2.2 quality system manual (QSM)—a manual describing
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. and documenting an agency’s quality system.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
C1093 − 15a
3.2.3 user—the person or organization engaging the agency 7.3 Supervising Laboratory Technician—The supervising
to provide tests; or using this practice to evaluate or accredit laboratory technician shall have at least five years experience
the agency. performing tests on materials, with at least two years testing
masonry materials. This person shall be able to demonstrate,
3.3 For additional terms used in this standard, refer to
e
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: C1093 − 15a C1093 − 15a
Standard Practice for
1
Accreditation of Testing Agencies for Masonry
This standard is issued under the fixed designation C1093; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected 7.2 in July 2016.
1. Scope*
1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system,
and it establishes minimum qualifications for agencies engaged in the testing of masonry materials.
1.2 Criteria are provided for evaluating the capability of an agency to properly perform designated tests on masonry materials,
and for establishing guidelines pertaining to an agency’s organization, personnel, facilities, and quality system. This practice may
be supplemented by more specific criteria and requirements for particular projects.
1.3 This practice can be used as a basis to evaluate testing agencies, and it is intended for use for the qualifying or accrediting
of testing agencies, or both, public or private, engaged in the testing of masonry materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C67 Test Methods for Sampling and Testing Brick and Structural Clay Tile
C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C140 Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C185 Test Method for Air Content of Hydraulic Cement Mortar
C230/C230M Specification for Flow Table for Use in Tests of Hydraulic Cement
C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C270 Specification for Mortar for Unit Masonry
C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C470/C470M Specification for Molds for Forming Concrete Test Cylinders Vertically
C780 Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry
C1072 Test Methods for Measurement of Masonry Flexural Bond Strength
C1232 Terminology of Masonry
C1506 Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
E4 Practices for Force Verification of Testing Machines
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
3. Terminology
3.1 Definitions:
1
This practice is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.07 on Standards
for Laboratory Accreditation.
Current edition approved Dec. 15, 2015. Published January 2016. Originally approved in 1988. Last previous edition approved in 2015 as C1093 – 15. DOI:
10.1520/C1093-15.10.1520/C1093-15E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
C1093 − 15a
3.1.1 quality system—the organizational structure, responsibilities, procedures, processes, capabilities, and resources for
implementing quality management.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 agency—the organization engaged to test masonry materials as required by a specification or contract.
3.2.2 quality system manual (QSM)—a manual describing and documenting an agency’s quality system.
3.2.3 user—the person or organization engaging the agency to provide tests; or using this practice to evaluate or accredit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.