Standard Specification for Stainless Steel Bars and Shapes

ABSTRACT
This specification covers hot-finished or cold-finished bars except bars for reforging. It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The bars shall be furnished in one of the following conditions: Condition A in which the bars are annealed, Condition H in which the bars are hardened and tempered at a relative temperature, Condition T in which the bars are hardened and tempered at a relatively high temperature, Condition S in which the bars are strain hardened or relatively light cold worked, and Condition B in which the bars are relatively severe cold worked. The material shall be subjected to a mechanical test to determine its tensile strength, yield strength, elongation, and Brinell hardness.
SCOPE
1.1 This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification.  
Note 1: For bars for reforging, see Specification A314.
Note 2: For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.
Note 3: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in  Annual Book of ASTM Standards, Vol. 02.04.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

General Information

Status
Historical
Publication Date
31-Dec-2015
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A276/A276M-16 - Standard Specification for Stainless Steel Bars and Shapes
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM A276/A276M-16 - Standard Specification for Stainless Steel Bars and Shapes
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A276/A276M −16
StandardSpecification for
1
Stainless Steel Bars and Shapes
This standard is issued under the fixed designationA276/A276M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* A751Test Methods, Practices, and Terminology for Chemi-
cal Analysis of Steel Products
1.1 This specification covers hot-finished or cold-finished
A1058 Test Methods for Mechanical Testing of Steel
bars except bars for reforging (Note 1). It includes rounds,
Products—Metric
squares,andhexagons,andhot-rolledorextrudedshapes,such
E527Practice for Numbering Metals and Alloys in the
asangles,tees,andchannelsinthemorecommonlyusedtypes
Unified Numbering System (UNS)
of stainless steels. The free-machining types (Note 2) for
3
general corrosion resistance and high-temperature service are 2.2 SAE Document:
covered in a separate specification. SAE J1086Recommended Practice for Numbering Metals
and Alloys
NOTE 1—For bars for reforging, see Specification A314.
NOTE 2—For free-machining stainless bars designed especially for
3. Ordering Information
optimum machinability, see Specification A582/A582M.
NOTE 3—There are standards covering high nickel, chromium, auste-
3.1 It is the responsibility of the purchaser to specify all
nitic corrosion, and heat-resisting alloy materials. These standards are
requirements that are necessary for material ordered under this
under the jurisdiction ofASTM Subcommittee B02.07 and may be found
in Annual Book of ASTM Standards, Vol. 02.04. specification. Such requirements may include but are not
limited to the following:
1.2 The values stated in either SI units or inch-pound units
3.1.1 Quantity (weight or number of pieces),
are to be regarded separately as standard. Within the text, the
3.1.2 Name of material: stainless steel,
SI units are shown in brackets. The values stated in each
3.1.3 Form (bars, angles, and so forth),
system may not be exact equivalents; therefore, each system
3.1.4 Condition (Section 4.1),
shall be used independently of the other. Combining values
3.1.5 Finish (Section 8 of Specification A484/A484M),
from the two systems may result in non-conformance with the
3.1.6 Surface preparation of shapes (Section 8 of Specifica-
standard. The inch-pound units shall apply unless the “M”
tion A484/A484M),
designation of this specification is specified in the order.
3.1.7 Applicable dimensions including size, thickness,
2. Referenced Documents
width, and length, l.
2
3.1.8 Cross section (round, square, and so forth),
2.1 ASTM Standards:
3.1.9 Type or UNS designation (Table 1),
A314Specification for Stainless Steel Billets and Bars for
3.1.10 ASTM designation and date of issue, and
Forging
3.1.11 Whetherbarsaretoberolledasbarsorcutfromstrip
A370Test Methods and Definitions for Mechanical Testing
or plate.
of Steel Products
3.1.12 Test for magnetic permeability when specified by
A484/A484MSpecification for General Requirements for
customer purchase order when ordering Types 201 and 205.
Stainless Steel Bars, Billets, and Forgings
3.1.13 ChoiceoftestingtrackfromtheoptionslistedinTest
A582/A582MSpecification for Free-Machining Stainless
Methods A1058 when material is ordered to an M suffix (SI
Steel Bars
units) product standard. If the choice of test track is not
1
specified in the order, then the default ASTM track shall be
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee
used as noted in Test Methods A1058
A01.17 on Flat-Rolled and Wrought Stainless Steel.
3.1.14 Supplementary requirements, and
Current edition approved Jan. 1, 2016. Published January 2016. Originally
3.1.15 Additional requirements.
approved in 1944. Last previous edition approved in 2015 as A276/A276M–15.
DOI: 10.1520/A0276_A0276M-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A276/A276M−16
A
TABLE 1 Chemical Requirements
Composition, %
UNS
Designa- Type
B
tion
K
Carbo
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A276/A276M − 15 A276/A276M − 16
Standard Specification for
1
Stainless Steel Bars and Shapes
This standard is issued under the fixed designation A276/A276M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares,
and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless
steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate
specification.
NOTE 1—For bars for reforging, see Specification A314.
NOTE 2—For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.
NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the
jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
2. Referenced Documents
2
2.1 ASTM Standards:
A314 Specification for Stainless Steel Billets and Bars for Forging
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A582/A582M Specification for Free-Machining Stainless Steel Bars
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A1058 Test Methods for Mechanical Testing of Steel Products—Metric
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3
2.2 SAE Document:
SAE J 1086 Recommended Practice for Numbering Metals and Alloys
3. Ordering Information
3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Such requirements may include but are not limited to the following:
3.1.1 Quantity (weight or number of pieces),
3.1.2 Name of material: stainless steel,
3.1.3 Form (bars, angles, and so forth),
3.1.4 Condition (Section 4.1),
3.1.5 Finish (Section 8 of Specification A484/A484M),
3.1.6 Surface preparation of shapes (Section 8 of Specification A484/A484M),
3.1.7 Applicable dimensions including size, thickness, width, and length, l.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Jan. 1, 2015Jan. 1, 2016. Published January 2015January 2016. Originally approved in 1944. Last previous edition approved in 20132015 as
A276 – 13a.A276/A276M – 15. DOI: 10.1520/A0276_A0276M-15.10.1520/A0276_A0276M-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A276/A276M − 16
3.1.8 Cross section (round, square, and so forth),
3.1.9 Type or UNS designation (Table 1),
3.1.10 ASTM designation and date of issue, and
3.1.11 Whether bars are to be rolled as bars or cut from strip or plate.
3.1.12 Test for magnetic permeability when specified by customer purchase order when ordering Types 201 and 205.
3.1.13 Choice of
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.