ASTM D7422-23
(Test Method)Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
SIGNIFICANCE AND USE
5.1 This test method was developed to evaluate the wear performance of engine oils in turbocharged and intercooled four-cycle diesel engines equipped with EGR and running on ultra-low sulfur diesel fuel. Obtain results from used oil analysis and component measurements before and after test.
5.2 The test method may be used for engine oil specification acceptance when all details of the procedure are followed.
SCOPE
1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including lead corrosion and wear of piston rings and cylinder liners in an engine equipped with exhaust gas recirculation and running on ultra-low sulfur diesel fuel.2 This test method is commonly referred to as the Mack T-12.
1.1.1 This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-12A. The procedures for the T-12 and T-12A are identical with the exception of the items specifically listed in Annex A9. Additionally, the procedure modifications listed in Annex A9 refer to the corresponding section of the T-12 procedure.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exception—Where there is no direct SI equivalent, such as the units for screw threads, National Pipe Threads/diameters, tubing size, and single source supply equipment specifications.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D7422 − 23
Standard Test Method for
Evaluation of Diesel Engine Oils in T-12 Exhaust Gas
1
Recirculation Diesel Engine
This standard is issued under the fixed designation D7422; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This test method covers an engine test procedure for
evaluating diesel engine oils for performance characteristics,
2. Referenced Documents
including lead corrosion and wear of piston rings and cylinder
3
liners in an engine equipped with exhaust gas recirculation and 2.1 ASTM Standards:
2
running on ultra-low sulfur diesel fuel. This test method is D86 Test Method for Distillation of Petroleum Products and
commonly referred to as the Mack T-12. Liquid Fuels at Atmospheric Pressure
1.1.1 This test method also provides the procedure for D93 Test Methods for Flash Point by Pensky-Martens
running an abbreviated length test, which is commonly referred Closed Cup Tester
to as the T-12A. The procedures for the T-12 and T-12A are D97 Test Method for Pour Point of Petroleum Products
identical with the exception of the items specifically listed in D130 Test Method for Corrosiveness to Copper from Petro-
Annex A9. Additionally, the procedure modifications listed in leum Products by Copper Strip Test
Annex A9 refer to the corresponding section of the T-12 D235 Specification for Mineral Spirits (Petroleum Spirits)
procedure. (Hydrocarbon Dry Cleaning Solvent)
D287 Test Method for API Gravity of Crude Petroleum and
1.2 The values stated in SI units are to be regarded as
Petroleum Products (Hydrometer/Method)
standard. No other units of measurement are included in this
D445 Test Method for Kinematic Viscosity of Transparent
standard.
and Opaque Liquids (and Calculation of Dynamic Viscos-
1.2.1 Exception—Where there is no direct SI equivalent,
ity)
such as the units for screw threads, National Pipe Threads/
D482 Test Method for Ash from Petroleum Products
diameters, tubing size, and single source supply equipment
D524 Test Method for Ramsbottom Carbon Residue of
specifications.
Petroleum Products
1.3 This standard does not purport to address all of the
D613 Test Method for Cetane Number of Diesel Fuel Oil
safety concerns, if any, associated with its use. It is the
D664 Test Method for Acid Number of Petroleum Products
responsibility of the user of this standard to establish appro-
by Potentiometric Titration
priate safety, health, and environmental practices and deter-
D976 Test Method for Calculated Cetane Index of Distillate
mine the applicability of regulatory limitations prior to use.
Fuels
See Annex A6 for specific safety precautions.
D1319 Test Method for Hydrocarbon Types in Liquid Petro-
1.4 This international standard was developed in accor-
leum Products by Fluorescent Indicator Adsorption
dance with internationally recognized principles on standard-
D2274 Test Method for Oxidation Stability of Distillate Fuel
ization established in the Decision on Principles for the
Oil (Accelerated Method)
Development of International Standards, Guides and Recom-
D2500 Test Method for Cloud Point of Petroleum Products
and Liquid Fuels
D2622 Test Method for Sulfur in Petroleum Products by
1
This test method is under the jurisdiction of ASTM Committee D02 on
Wavelength Dispersive X-ray Fluorescence Spectrometry
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
D2709 Test Method for Water and Sediment in Middle
Subcommittee D02.B0 on Automotive Lubricants.
Distillate Fuels by Centrifuge
Current edition approved Dec. 1, 2023. Published December 2023. Originally
approved in 2008. Last previous edition approved in 2022 as D7422 – 22. DOI:
10.1520/D7422-23.
2
The ASTM Test Monitoring Center will update changes in this test method by
3
means of Information Letters. Information letters may be obtained from the ASTM For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Test Monitoring Center, 203 Armstrong Drive, Freeport, PA 16229, contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
www.astmtmc.org, Attention: Director. This edition incorporates revisions in all Standards volume information, refer to the standard’s Document Summary page on
Information Letters through No. 23-1. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Co
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7422 − 22 D7422 − 23
Standard Test Method for
Evaluation of Diesel Engine Oils in T-12 Exhaust Gas
1
Recirculation Diesel Engine
This standard is issued under the fixed designation D7422; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including
lead corrosion and wear of piston rings and cylinder liners in an engine equipped with exhaust gas recirculation and running on
2
ultra-low sulfur diesel fuel. This test method is commonly referred to as the Mack T-12.
1.1.1 This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the
T-12A. The procedures for the T-12 and T-12A are identical with the exception of the items specifically listed in Annex A9.
Additionally, the procedure modifications listed in Annex A9 refer to the corresponding section of the T-12 procedure.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exception—Where there is no direct SI equivalent, such as the units for screw threads, National Pipe Threads/diameters,
tubing size, and single source supply equipment specifications.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. See Annex A6 for specific safety precautions.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D97 Test Method for Pour Point of Petroleum Products
D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.B0 on Automotive Lubricants.
Current edition approved April 1, 2022Dec. 1, 2023. Published April 2022December 2023. Originally approved in 2008. Last previous edition approved in 20192022 as
D7422 – 19.D7422 – 22. DOI: 10.1520/D7422-22.10.1520/D7422-23.
2
The ASTM Test Monitoring Center will update changes in this test method by means of Information Letters. Information letters may be obtained from the ASTM Test
Monitoring Center, 203 Armstrong Drive, Freeport, PA 16229, www.astmtmc.org, Attention: Director. This edition incorporates revisions in all Information Letters through
No. 21-1.23-1.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7422 − 23
D287 Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer/Method)
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D482 Test Method for Ash from Petroleum Products
D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products
D613 Test Method for Cetane Number of Diesel Fuel Oil
D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration
D976 Test Method for Calculated Cetane Index of Distillate Fuels
D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.