ASTM A20/A20M-10
(Specification)Standard Specification for General Requirements for Steel Plates for Pressure Vessels
Standard Specification for General Requirements for Steel Plates for Pressure Vessels
ABSTRACT
This specification covers a group of common requirements that apply to rolled steel plates for pressure vessels. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace process. Sampling and methods for chemical analysis are discussed. Yield strength tests, tension tests, and notch-toughness tests shall be made in accordance to the product specification to conform to the specified requirements.
SCOPE
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A20/A20M – 10
Standard Specification for
1
General Requirements for Steel Plates for Pressure Vessels
This standard is issued under the fixed designation A20/A20M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
A
1. Scope*
Title of Specification ASTM Designation
Pressure Vessel Plates, Carbon Steel, Manganese- A562/A562M
2
1.1 This general requirements specification covers a group
Titanium for Glass or Diffused Metallic Coatings
of common requirements that, unless otherwise specified in the
Pressure Vessel Plates, Carbon Steel, High Strength, for A612/A612M
Moderate and Lower Temperature Service
applicable product specification, apply to rolled steel plates for
Pressure Vessel Plates, Five Percent Nickel Alloy Steel, A645/A645M
pressure vessels covered by each of the following product
Specially Heat Treated
specifications issued by ASTM:
Pressure Vessel Plates, Carbon-Manganese, for A662/A662M
Moderate and Lower Temperature Service
A
Title of Specification ASTM Designation
Pressure Vessel Plates, Carbon Steel, Quenched and A724/A724M
Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M
Tempered, for Welded Layered Pressure Vessels
Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M
Pressure Vessel Plates, Alloy Steel and High-Strength A734/A734M
Pressure Vessel Plates, Alloy Steel, Manganese- A225/A225M
Low-Alloy Steel, Quenched and Tempered
Vanadium
Pressure Vessel Plates, Low-Carbon Manganese- A735/A735M
Pressure Vessel Plates, Carbon Steel, Low- and A285/A285M
Molybdenum-Columbium Alloy Steel, for Moderate and
Intermediate-Tensile Strength
Lower Temperature Service
Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M
Pressure Vessel Plates, Low-Carbon Age-Hardening A736/A736M
Pressure Vessel Plates, Alloy Steel, Manganese- A302/A302M
Nickel-Copper-Chromium-Molybdenum-Columbium
Molybdenum and Manganese-Molybdenum-Nickel
Alloy Steel
Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel A353/A353M
Pressure Vessel Plates, High-Strength Low-Alloy Steel A737/A737M
Double-Normalized and Tempered
Pressure Vessel Plates, Heat-Treated, Carbon- A738/A738M
Pressure Vessel Plates, Alloy Steel, Chromium- A387/A387M
Manganese-Silicon Steel, for Moderate and Lower
Molybdenum
Temperature Service
Pressure Vessel Plates, Carbon Steel, High Strength A455/A455M
Pressure Vessel Plates, Alloy Steel, Chromium- A832/A832M
Manganese
Molybdenum-Vanadium
Pressure Vessel Plates, Carbon Steel, for Intermediate- A515/A515M
Pressure Vessel Plates, Produced by the Thermo- A841/A841M
and Higher-Temperature Service
Mechanical Control Process (TMCP)
Pressure Vessel Plates, Carbon Steel, Moderate- and A516/A516M
Pressure Vessel Plates, 9 % Nickel Alloy, Produced A844/A844M
Lower-Temperature Service
by the Direct-Quenching Process
Pressure Vessel Plates, Alloy Steel, High-Strength, A517/A517M
Pressure Vessel Plates, 9 % Nickel Alloy, Produced A844/A844M
Quenched and Tempered
by the Direct-Quenching Process
Pressure Vessel Plates, Alloy Steel, Quenched and A533/A533M
Pressure Vessel Plates, 9 % Nickel Alloy, Produced A844/A844M
Tempered Manganese-Molybdenum and Manganese-
by the Direct-Quenching Process
Molybdenum- Nickel
Pressure Vessel Plates, Alloy Steel, Chromium- A1017/A1017M
Pressure Vessel Plates, Heat-Treated, Carbon- A537/A537M
Molybdenum-Tungsten
Manganese-Silicon Steel
Pressure Vessel Plates, Alloy Steel, Higher Strength A1041/A1041M
Pressure Vessel Plates, Alloy Steel, Quenched and A542/A542M
Chromium-Molybdenum-Tungsten
Tempered Chromium-Molybdenum
Pressure Vessel Plates, Alloy Steel, Quenched and A543/A543M A
These designations refer to the latest issue of the respective specification
Tempered Nickel-Chromium-Molybdenum
which appears in the Annual Book of ASTM Standards, Vol 01.04.
Pressure Vessel Plates, Alloy Steel, Quenched and A553/A553M
Tempered 8 and 9 Percent Nickel
1.1.1 This general requirements specification also covers a
group of supplementary requirements that are applicable to
severaloftheaboveproductspecificationsasindicatedtherein.
Such requirements are provided for use if additional testing or
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
additional restrictions are required by the purchaser, and apply
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
only if specified individually in the purchase order.
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct. 1, 2010. Published November 2010. Originally
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A20/A20M–09 Designation: A20/A20M – 10
Standard Specification for
1
General Requirements for Steel Plates for Pressure Vessels
This standard is issued under the fixed designation A20/A20M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the
applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product
specifications issued by ASTM:
A
Title of Specification ASTM Designation
Pressure Vessel Plates, Alloy Steel, Chromium- A202/A202M
Manganese Silicon
Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M
Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M
Pressure Vessel Plates, Alloy Steel, Manganese- A225/A225M
Vanadium
Pressure Vessel Plates, Carbon Steel, Low- and A285/A285M
Intermediate-Tensile Strength
Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M
Pressure Vessel Plates, Alloy Steel, Manganese- A302/A302M
Molybdenum and Manganese-Molybdenum-Nickel
Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel A353/A353M
Double-Normalized and Tempered
Pressure Vessel Plates, Alloy Steel, Chromium- A387/A387M
Molybdenum
Pressure Vessel Plates, Carbon Steel, High Strength A455/A455M
Manganese
Pressure Vessel Plates, Carbon Steel, for Intermediate- A515/A515M
and Higher-Temperature Service
Pressure Vessel Plates, Carbon Steel, Moderate- and A516/A516M
Lower-Temperature Service
Pressure Vessel Plates, Alloy Steel, High-Strength, A517/A517M
Quenched and Tempered
Pressure Vessel Plates, Alloy Steel, Quenched and A533/A533M
Tempered Manganese-Molybdenum and Manganese-
Molybdenum- Nickel
Pressure Vessel Plates, Heat-Treated, Carbon- A537/A537M
Manganese-Silicon Steel
Pressure Vessel Plates, Alloy Steel, Quenched and A542/A542M
Tempered Chromium-Molybdenum
Pressure Vessel Plates, Alloy Steel, Quenched and A543/A543M
Tempered Nickel-Chromium-Molybdenum
Pressure Vessel Plates, Alloy Steel, Quenched and A553/A553M
Tempered 8 and 9 Percent Nickel
A
Title of Specification ASTM Designation
Pressure Vessel Plates, Carbon Steel, Manganese- A562/A562M
Titanium for Glass or Diffused Metallic Coatings
Pressure Vessel Plates, Carbon Steel, High Strength, for A612/A612M
Moderate and Lower Temperature Service
Pressure Vessel Plates, Five Percent Nickel Alloy Steel, A645/A645M
Specially Heat Treated
Pressure Vessel Plates, Carbon-Manganese, for A662/A662M
Moderate and Lower Temperature Service
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct. 1, 2009.2010. Published November 2009.2010. Originally approved in 1950. Last previous edition approved in 20072009 as
A20/A20M – 079. DOI: 10.1520/A0020_A0020M-109.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-20/SA-20M in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A20/A20M – 10
Pressure Vessel Plates, Carbon Steel, Quenched and A724/A724M
Tempered, for Welded Layered Pressure Vessels
Pressure Vessel Plates, Alloy Steel and High-Strength A734/A734M
Low-Alloy Steel, Quenched and Tempered
Pressure Vessel Plates, Low-Carbon Manganese- A735/A735M
Molybdenum-Columbium Alloy Steel, for Moderate and
Lower Temperature Service
Pressure Vessel Plates, Low-Carbon Age-Hardening A736/A736M
Nickel-Copper-Chromium-Molybdenum-Columbium
Alloy Steel
Pressure Vessel Plates, High-Strength Low-Alloy Steel A737/A737M
Pressure Vessel Plates, Heat-Treated, Carbon- A738/A738M
Manganese-Silicon Steel, for Moderate and Lower
Temperature Service
Pressure-Vessel Plates, Quenched and Tempered, A782/A782M
Manganese-Chromium-Molybdenum-Silicon-
Zirconium Alloy Steel
Pressure Vessel Plates, Alloy Steel, Chromium- A832/A832M
Molybdenum-Vanadium
Pressure Vessel Plates, Produced by the Thermo- A841/
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A20/A20M–09 Designation: A20/A20M – 10
Standard Specification for
1
General Requirements for Steel Plates for Pressure Vessels
This standard is issued under the fixed designation A20/A20M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the
applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product
specifications issued by ASTM:
A
Title of Specification ASTM Designation
Pressure Vessel Plates, Alloy Steel, Chromium- A202/A202M
Manganese Silicon
Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M
Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M
Pressure Vessel Plates, Alloy Steel, Manganese- A225/A225M
Vanadium
Pressure Vessel Plates, Carbon Steel, Low- and A285/A285M
Intermediate-Tensile Strength
Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M
Pressure Vessel Plates, Alloy Steel, Manganese- A302/A302M
Molybdenum and Manganese-Molybdenum-Nickel
Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel A353/A353M
Double-Normalized and Tempered
Pressure Vessel Plates, Alloy Steel, Chromium- A387/A387M
Molybdenum
Pressure Vessel Plates, Carbon Steel, High Strength A455/A455M
Manganese
Pressure Vessel Plates, Carbon Steel, for Intermediate- A515/A515M
and Higher-Temperature Service
Pressure Vessel Plates, Carbon Steel, Moderate- and A516/A516M
Lower-Temperature Service
Pressure Vessel Plates, Alloy Steel, High-Strength, A517/A517M
Quenched and Tempered
Pressure Vessel Plates, Alloy Steel, Quenched and A533/A533M
Tempered Manganese-Molybdenum and Manganese-
Molybdenum- Nickel
Pressure Vessel Plates, Heat-Treated, Carbon- A537/A537M
Manganese-Silicon Steel
Pressure Vessel Plates, Alloy Steel, Quenched and A542/A542M
Tempered Chromium-Molybdenum
Pressure Vessel Plates, Alloy Steel, Quenched and A543/A543M
Tempered Nickel-Chromium-Molybdenum
Pressure Vessel Plates, Alloy Steel, Quenched and A553/A553M
Tempered 8 and 9 Percent Nickel
A
Title of Specification ASTM Designation
Pressure Vessel Plates, Carbon Steel, Manganese- A562/A562M
Titanium for Glass or Diffused Metallic Coatings
Pressure Vessel Plates, Carbon Steel, High Strength, for A612/A612M
Moderate and Lower Temperature Service
Pressure Vessel Plates, Five Percent Nickel Alloy Steel, A645/A645M
Specially Heat Treated
Pressure Vessel Plates, Carbon-Manganese, for A662/A662M
Moderate and Lower Temperature Service
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct. 1, 2009.2010. Published November 2009.2010. Originally approved in 1950. Last previous edition approved in 20072009 as
A20/A20M – 079. DOI: 10.1520/A0020_A0020M-109.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-20/SA-20M in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A20/A20M – 10
Pressure Vessel Plates, Carbon Steel, Quenched and A724/A724M
Tempered, for Welded Layered Pressure Vessels
Pressure Vessel Plates, Alloy Steel and High-Strength A734/A734M
Low-Alloy Steel, Quenched and Tempered
Pressure Vessel Plates, Low-Carbon Manganese- A735/A735M
Molybdenum-Columbium Alloy Steel, for Moderate and
Lower Temperature Service
Pressure Vessel Plates, Low-Carbon Age-Hardening A736/A736M
Nickel-Copper-Chromium-Molybdenum-Columbium
Alloy Steel
Pressure Vessel Plates, High-Strength Low-Alloy Steel A737/A737M
Pressure Vessel Plates, Heat-Treated, Carbon- A738/A738M
Manganese-Silicon Steel, for Moderate and Lower
Temperature Service
Pressure-Vessel Plates, Quenched and Tempered, A782/A782M
Manganese-Chromium-Molybdenum-Silicon-
Zirconium Alloy Steel
Pressure Vessel Plates, Alloy Steel, Chromium- A832/A832M
Molybdenum-Vanadium
Pressure Vessel Plates, Produced by the Thermo- A841/
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.