ASTM F2653-11

Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders

SCOPE
1.1 This specification covers the male threaded connection used to connect a CO2 Control Valve or Compressed Air Regulator with an output pressure of 10 342 kPa (1800 psig) or less for use with a paintball marker to a DOT approved cylinder.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Apr-2011
• ICS: 23.060.40 - Pressure regulators
• Technical Committee: F08 - Sports Equipment, Playing Surfaces, and Facilities
• Drafting Committee: F08.24 - Paintball and Equipment

Relations

• Replaces: ASTM F2653-07 - Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders
• Effective Date: 01-May-2011
• Replaced By: ASTM F2653-11(2015) - Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders
• Effective Date: 01-Apr-2015
• Referred By: ASTM F2748-19 - Standard Specification for Airsoft Guns
• Effective Date: 01-May-2011
• Referred By: ASTM F1777-19(2023) - Standard Practice for Paintball Game Site Operation
• Effective Date: 01-May-2011
• Referred By: ASTM F3100-15(2023) - Standard Practice for Low Impact Paintball Field Operation
• Effective Date: 01-May-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2653 −11 AnAmerican National Standard
Standard Specification for
Paintball Valve Male Threaded Connection for Use with
1
Approved Cylinders
This standard is issued under the fixed designation F2653; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.3 CGA Standards:
CGA S-1.1 Pressure Relief Device Standards-Part
1.1 This specification covers the male threaded connection
1-Cylinders for Compressed Gases
used to connect a CO Control Valve or Compressed Air
2 5
2.4 Federal Standards:
Regulator with an output pressure of 10 342 kPa (1800 psig) or
FED-STD-H28/9A24 March 1989 Federal Standard Screw-
less for use with a paintball marker to a DOT approved
Thread Standards for Federal Services Section 9 Gas
cylinder.
Cylinder Valve Outlet and Inlet Threads
NBS Handbook H-28
1.2 The values stated in SI units are to be regarded as
6
standard. The values given in parentheses are for information
2.5 Code of Federal Regulations:
only. DOT 49 CFR 173
DOT 49 CFR 178
1.3 This standard does not purport to address all of the
DOT CFFC 4th Revision
safety concerns, if any, associated with its use. It is the
7
2.6 ANSI Standards:
responsibility of the user of this standard to establish appro-
ANSI Y14.5M–1994 Dimensioning and Tolerancing
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
3. Connector Gender Assignment
3.1 The male connector is that connector which is config-
2. Referenced Documents
ured as part of the CO control valve or compressed air
2
2
2.1 ASTM Standards:
regulator for use with a paintball marker.
D2240 Test Method for Rubber Property—Durometer Hard-
3.2 The female connector is that connector which is config-
ness
ured as part of the DOT approved cylinder.
F1750 Specification for Paintball Marker Threaded-
Propellant Source Interface
4. Materials and Manufacture
F2030 Specification for Paintball Cylinder Burst Disk As-
4.1 The male connector shall be made from materials that
semblies
are compatible with CO , compressed air or gaseous nitrogen.
2
3
2.2 Military Standards:
4.2 The O-ring seal shall be made from an elastomer
AMS7277 O-Ring Dash Sizes
compatible with CO , compressed air or gaseous nitrogen used
2
MS28775 Packing, Preformed, Hydraulic, +275 Deg. F
to power paintball markers. The O-ring seal shall have a
(“O”-Ring)
hardness that will register a Type A durometer reading of
between70to90 65.TheO-ringshallconformdimensionally
to the requirements in AMS7277 or MS28775 based upon the
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports
size and material recommendations of the cylinder manufac-
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
turer.
Subcommittee F08.24 on Paintball and Equipment.
Current edition approved May 1, 2011. Published June 2011. Originally
approved in 2007. Last previous edition approved in 2007 as F2653 – 07. DOI:
4
10.1520/F2653-11. Available from Compressed Gas Association (CGA), 4221 Walney Rd., 5th
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Floor, Chantilly, VA 20151-2923, http://www.cganet.com.
5
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from The National Conference on Weights and Measures, 15245
Standards volume information, refer to the standard’s Document Summary page on Shady Grove Road, Suite 130, Rockville, MD 20850.
6
the ASTM website. Available from U.S. Department of Transportation, 400 7th Street, SW,
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Washington, D.C. 20590.
7
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:// Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
www.dodssp.daps.mil. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2653−11
TABLE 1 Minimum Valve Thread Requirements by DOT Cylinder
4.3 The O-ring seal shall be installed on the male connector
Type
in the groove described by Dimensions C and D on Fig. 1.
DOT Cylinder Min. Valve Threads Test Pressure
4.4 The male connectors shall not have any sharp edges or
3AL Min. 6 full threads 5/3 Operating Pressure
FRP Min. 6 full threads 5/3 Operating Pressure
hanging burrs. All sharp edges will be broken R.38 MAX
CFFC 4th Rev. Min. 6 full threads 5/3 Operating Pressure
(R.015 MAX).
3E Min. 4 full threads 5/3 Operating Pressure
4.5 The male connector
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2653–07 Designation: F2653 – 11
Standard Specification for
Paintball Valve Male Threaded Connection for Use with
1
Approved Cylinders
This standard is issued under the fixed designation F2653; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the male threaded connection used to connect a CO Control Valve or CompressedAir Regulator
2
with an output pressure of 10 342 kPa (1800 psig) or less for use with a paintball marker to a DOT approved cylinder.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D2240 Test Method for Rubber PropertyDurometer Hardness
F1750 Specification for Paintball Marker Threaded-Propellant Source Interface
F2030 Specification for Paintball Cylinder Burst Disk Assemblies
3
2.2 Military Standards:
AMS7277 O-Ring Dash Sizes
MS28775 Packing, Preformed, Hydraulic, +275 Deg. F (“O”-Ring)
4
2.3 CGA Standards:
CGA S-1.1 Pressure Relief Device Standards-Part 1-Cylinders for Compressed Gases
5
2.4 Federal Standards:
FED-STD-H28/9A 24 March 1989 Federal Standard Screw-Thread Standards for Federal Services Section 9 Gas Cylinder
Valve Outlet and Inlet Threads
NBS Handbook H-28
6
2.5 Code of Federal Regulations:
DOT 49 CFR 173
DOT 49 CFR 178
DOT CFFC 4th Revision
7
2.6 ANSI Standards:
ANSI Y14.5M–1994 Dimensioning and Tolerancing
3. Connector GenderAssignment
3.1 The male connector is that connector which is configured as part of the CO control valve or compressed air regulator for
2
use with a paintball marker.
3.2 The female connector is that connector which is configured as part of the DOT approved cylinder.
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 on
Paintball and Equipment.
Current edition approved May 1, 2007. Published June 2007. DOI: 10.1520/F2653-07.
Current edition approved May 1, 2011. Published June 2011. Originally approved in 2007. Last previous edition approved in 2007 as F2653 – 07. DOI: 10.1520/F2653-11.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
4
Available from Compressed Gas Association (CGA), 4221 Walney Rd., 5th Floor, Chantilly, VA 20151-2923, http://www.cganet.com.
5
Available from The National Conference on Weights and Measures, 15245 Shady Grove Road, Suite 130, Rockville, MD 20850.
6
Available from U.S. Department of Transportation, 400 7th Street, SW, Washington, D.C. 20590.
7
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2653 – 11
4. Materials and Manufacture
4.1 The male connector shall be made from materials that are compatible with CO , compressed air or gaseous nitrogen.
2
4.2 The O-ring seal shall be made from an elastomer compatible with CO , compressed air or gaseous nitrogen used to power
2
paintball markers. The O-ring seal shall have a hardness that will register a Type A durometer reading of between 70 to 90 6 5.
The O-ring shall conform dimensionally to the requirements in AMS7277 or MS28775 based upon the size and material
recommendations of the cylinder manufacturer.
4.3 The O-ring seal shall be installed on the male connector in the groove described by Dimensions C and D on Fig. 1.
TABLE 1 Minimum Valve Thread Requirements by DOT Cylinder
Type
DOT Cylinder Min. Valve Threads Tes
...