ASTM F1245-19
(Specification)Standard Specification for Faucets, Single and Double, Compression and Self-Closing Type, Shipboard
Standard Specification for Faucets, Single and Double, Compression and Self-Closing Type, Shipboard
ABSTRACT
This specification covers single- and double compression and self-closing faucets for shipboard plumbing installations. Faucets may be classified into nine types: Type I is the standard (bibb) with three classes namely Class A (compression, plain end), Class B (compression, hose end), and Class C (self-closing); Type II is a lavatory, self-closing, low spout faucet with two classes which are Class A (fast-closing) and Class B (slow-closing, depression type); Type III is a folding lavatory,self-closing faucet; Type IV is an elbow operated faucet, Type V is a faucet with lavatory, combination water supply and drain fixture; Type VI is a faucet with combination supply fixture swing spout for use on galley sinks; Type VII is a faucet with single supply fixture swing spout for use with steam kettles and urns and this type has two classes namely Class A which has spout for overhead supply and Class B which has spout for riser supply; Type VIII is a faucet with supply fixture for pressed metal and shock mounted china lavatories; and Type IX which is a faucet with lavatory and combination of water supply and drain fixtures. Faucet bodies shall be made of bronze and handles shall be of commercial grade cast or forged brass or bronze. Bonnets, handwheels, and nuts shall be of commercial quality brass or bronze; machine screws shall be made of commercial brass. Seat washers shall be of a rubber or fiber material and suitable for a certain water temperature range without deterioration of material. Springs for self-closing faucets shall be of corrosionresisting steel, phosphor bronze, or nickel copper. All samples shall be subjected to a hydrostatic test.
SCOPE
1.1 This specification covers single- and double-compression and self-closing faucets for shipboard plumbing installations.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 10, of this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F1245 −19 An American National Standard
Standard Specification for
Faucets, Single and Double, Compression and Self-Closing
1
Type, Shipboard
This standard is issued under the fixed designation F1245; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D6251/D6251MSpecificationforWood-CleatedPanelboard
Shipping Boxes
1.1 This specification covers single- and double-
D6880/D6880MSpecification for Wood Boxes
compression and self-closing faucets for shipboard plumbing
3
2.2 ASME Standard:
installations.
B1.1Unified Inch Screw Threads, UN and UNR Thread
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
Form
as standard. The values given in parentheses are mathematical 4
2.3 ASQ Standard:
conversions to SI units that are provided for information only
ANSI/ASQ Z1.4Sampling Procedures and Tables for In-
and are not considered standard.
spection by Attributes
5
1.3 The following precautionary caveat pertains only to the
2.4 Federal Specifications:
test methods portion, Section 10, of this standard. This stan-
PPP-B-566Boxes, Folding, Paperboard
dard does not purport to address all of the safety concerns, if
PPP-B-676Boxes, Setup
5
any, associated with its use. It is the responsibility of the user
2.5 Military Standards:
of this standard to establish appropriate safety, health, and
MIL-STD-129Marking for Shipment and Storage
environmental practices and determine the applicability of
MIL-STD-2073-1Practice for Military Packaging
5
regulatory limitations prior to use.
2.6 Naval Sea Systems Command (NAVSEA):
1.4 This international standard was developed in accor-
NAVSEA Drawing 803-5959206Faucet, Metering
dance with internationally recognized principles on standard-
NAVSEADrawing 805-1623970Unit, Lavatory for Officers
ization established in the Decision on Principles for the
Station
6
Development of International Standards, Guides and Recom-
2.7 SAE International Standards:
mendations issued by the World Trade Organization Technical
SAE-AMS-QQ-C-320ChromiumPlating(Electrodeposited)
Barriers to Trade (TBT) Committee.
SAE-AMS-QQ-N-290Nickel Plating (Electrodeposited)
2. Referenced Documents
3. Classification
2
2.1 ASTM Standards:
3.1 Faucets shall be of the following types and classes as
B62Specification for Composition Bronze or Ounce Metal
specified (see 4.1):
Castings
3.1.1 Type I—Standard (bibb):
B584Specification for Copper Alloy Sand Castings for
3.1.1.1 Class A—Compression, plain end.
General Applications
3.1.1.2 Class B—Compression, hose end.
D1974/D1974MPractice for Methods of Closing, Sealing,
3.1.1.3 Class C—Self-closing.
and Reinforcing Fiberboard Boxes
3.1.2 Type II—Lavatory, self-closing, low spout.
D5118/D5118MPracticeforFabricationofFiberboardShip-
3.1.2.1 Class A—Fast-closing.
ping Boxes
3.1.2.2 Class B—Slow-closing, depression type.
3.1.3 Type III—Folding lavatory, self-closing.
1
This specification is under the jurisdiction ofASTM Committee F25 on Ships
3
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on Available from American Society of Mechanical Engineers (ASME), ASME
Machinery and Piping Systems. International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
Current edition approved Dec. 1, 2019. Published January 2020. Originally www.asme.org.
4
approved in 1989. Last previous edition approved in 2012 as F1245–89 (2012). Available from American Society for Quality (ASQ), 600 N. Plankinton Ave.,
DOI: 10.1520/F1245-19. Milwaukee, WI 53203, http://www.asq.org.
2 5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
6
Standards volume information, refer to the standard’s Document Summary page on AvailablefromSAEInternational(SAE),400CommonwealthDr.,Warrendale,
the ASTM website. PA 15096, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1245−19
3.1.4 Type IV—Elbow operated.
3.1.5 Type V—Lavatory, combination water supply and
drain fixture.
3.1.6 Type VI—Combination supply fixture swing spout for
use on galley sinks.
3.1.7 Type VII—Single supply fixture swing spout
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1245 − 89 (Reapproved 2012) F1245 − 19 An American National Standard
Standard Specification for
Faucets, Single and Double, Compression and Self-Closing
1
Type, Shipboard
This standard is issued under the fixed designation F1245; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers single- and double-compression and self-closing faucets for shipboard plumbing installations.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 10, of this standard. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
B62 Specification for Composition Bronze or Ounce Metal Castings
B584 Specification for Copper Alloy Sand Castings for General Applications
D1974/D1974M Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes
D5118/D5118M Practice for Fabrication of Fiberboard Shipping Boxes
D6251/D6251M Specification for Wood-Cleated Panelboard Shipping Boxes
D6880/D6880M Specification for Wood Boxes
3
2.2 American National Standards Institute ASME Standard:
B1.1 Unified Inch Screw Threads (UNThreads, UN and UNR Thread Form)Form
4
2.3 ASQ Standard:
ANSI/ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes
5
2.4 Federal Specifications:
PPP-B-566 Boxes, Folding, Paperboard
PPP-B-585 Boxes, Wood, Wirebound
PPP-B-591 Boxes, Shipping, Fiberboard, Wood-Cleated
PPP-B-601 Boxes, Wood, Cleated-Plywood
PPP-B-621 Boxes, Wood, Nailed and Lock-Corner
PPP-B-636 Box, Shipping, Fiberboard
PPP-B-676 Boxes, Setup
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery and Piping Systems.
Current edition approved May 1, 2012Dec. 1, 2019. Published May 2012January 2020. Originally approved in 1989. Last previous edition approved in 20062012 as
F1245 – 89 (2012). (2006). DOI: 10.1520/F1245-89R12.10.1520/F1245-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, Society of Mechanical Engineers (ASME), ASME International Headquarters,
Two Park Ave., New York, NY 10036, http://www.ansi.org.10016-5990, http://www.asme.org.
4
Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Milwaukee, WI 53203, http://www.asq.org.
5
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA
19111-5098, http://dodssp.daps.dla.mil.19111-5094, http://quicksearch.dla.mil.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1245 − 19
QQ-N-290 Nickel Plating (Electrodeposited)
QQ-C-320 Chromium Plating (Electrodeposited)
4
2.4 Military Specification:
MIL-P-116 Preservation, Methods of
5
2.5 Military Standards:
MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes
MIL-STD-129 Marking for Shipment and Storage
MIL-STD-2073-1 Practice for Military Packaging
5
2.6 Naval Sea Systems Command (NAVSEA):
NAVSE
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.