ASTM D5132-19
(Test Method)Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles
Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles
SIGNIFICANCE AND USE
5.1 This test method provides a standard laboratory procedure for measuring and comparing the burning rates of polymeric materials under specified controlled conditions.
5.2 The rate of burning is affected by such factors as density, direction of rise, and type and amount of surface treatments. The thickness of the finished specimens must also be taken into account. These factors must be considered in order to compare materials on the same basis.
5.3 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.
SCOPE
1.1 This test method is intended for use as a small-scale laboratory procedure for comparing the relative horizontal burning rates of polymeric materials used in occupant compartments of motor vehicles.
1.2 During the course of combustion, gases or vapors, or both, are evolved that are potentially hazardous to personnel. Adequate precautions shall be taken to protect the operator.
1.3 Units—The values stated in SI units are to be regarded as standard.
1.4 This test method, Federal Safety Standard MVSS 302, SAE J369, and ISO 3795 address the same subject matter, but differ in technical content.
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.
1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
Note 1: There is no known ISO equivalent to this standard.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5132 − 19
Standard Test Method for
Horizontal Burning Rate of Polymeric Materials Used in
1
Occupant Compartments of Motor Vehicles
This standard is issued under the fixed designation D5132; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This test method is intended for use as a small-scale 2.1 ASTM Standards:
laboratory procedure for comparing the relative horizontal D883 Terminology Relating to Plastics
burning rates of polymeric materials used in occupant com- D5025 Specification for Laboratory Burner Used for Small-
partments of motor vehicles. Scale Burning Tests on Plastic Materials
E176 Terminology of Fire Standards
1.2 During the course of combustion, gases or vapors, or
E456 Terminology Relating to Quality and Statistics
both, are evolved that are potentially hazardous to personnel.
E691 Practice for Conducting an Interlaboratory Study to
Adequate precautions shall be taken to protect the operator.
Determine the Precision of a Test Method
1.3 Units—The values stated in SI units are to be regarded
E2935 Practice for Conducting Equivalence Testing in
as standard.
Laboratory Applications
1.4 This test method, Federal Safety Standard MVSS 302,
2.2 Federal Safety Standard:
SAE J369, and ISO 3795 address the same subject matter, but
MVSS 302 (49 CFR 571.302) Flammability of Interior
differ in technical content.
Materials-Passenger Cars, Multipurpose Passenger
3
1.5 This standard is used to measure and describe the Vehicles, Trucks and Buses
response of materials, products, or assemblies to heat and
2.3 SAE Standard:
flame under controlled conditions, but does not by itself
SAE J369 Flammability of Polymeric Interior Materials -
4
incorporate all factors required for fire hazards or fire risk
Horizontal Test Method
assessment of materials, products, or assemblies under actual
2.4 ISO Standard:
fire conditions.
ISO 3795 Road vehicles, and tractors and machinery for
1.6 This standard does not purport to address all of the
agriculture and forestry—Determination of burning be-
safety concerns, if any, associated with its use. It is the 5
havior of interior materials
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
3. Terminology
mine the applicability of regulatory limitations prior to use.
3.1 Definitions—Terms used in this standard are defined in
Specific hazard statements are given in Section 7.
accordance with D883, unless otherwise specified. For terms
1.7 Fire testing is inherently hazardous. Adequate safe-
relating to precision and bias and associated issues, the terms
guards for personnel and property shall be employed in
used in this standard are defined in accordance with Terminol-
conducting these tests.
ogy E456. For terms relating to fire, the terms in this standard
NOTE 1—There is no known ISO equivalent to this standard.
are defined in accordance with Terminology E176.
1.8 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
2
Development of International Standards, Guides and Recom- For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
mendations issued by the World Trade Organization Technical
Standards volume information, refer to the standard’s Document Summary page on
Barriers to Trade (TBT) Committee.
the ASTM website.
3
United States Code of Federal Regulations, 49 CFR 571.302, 36 FR 28991,
available from Superintendent of Documents, U.S. Government Printing Office,
1
This test method is under the jurisdiction ofASTM Committee D20 on Plastics Washington, DC 20402.
4
and is the direct responsibility of Subcommittee D20.30 on Thermal Properties. Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Current edition approved Dec. 1, 2019. Published January 2020. Originally Dr., Warrendale, PA 15096-0001.
5
approved in 1990. Last previous edition approved in 2017 as D5132 – 17. DOI: Available from International Organization for Standardization (ISO), 1 rue de
10.1520/D5132-19. Varembé, Case postale 56, CH-1211, Geneva 20, Switzerland.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5132 − 19
NOTE 2—It is acceptable to mount the burner on the door, as
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5132 − 17 D5132 − 19
Standard Test Method for
Horizontal Burning Rate of Polymeric Materials Used in
1
Occupant Compartments of Motor Vehicles
This standard is issued under the fixed designation D5132; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This test method is intended for use as a small-scale laboratory procedure for comparing the relative horizontal burning rates
of polymeric materials used in occupant compartments of motor vehicles.
1.2 During the course of combustion, gases or vapors, or both, are evolved that are potentially hazardous to personnel. Adequate
precautions shall be taken to protect the operator.
1.3 Units—The values stated in SI units are to be regarded as standard.
1.4 This test method, Federal Safety Standard MVSS 302, SAE J369, and ISO 3795 address the same subject matter, but differ
in technical content.
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials,
products, or assemblies under actual fire conditions.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.
1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these
tests.
NOTE 1—There is no known ISO equivalent to this standard.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
D5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
E176 Terminology of Fire Standards
E456 Terminology Relating to Quality and Statistics
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E2935 Practice for Conducting Equivalence Testing in Laboratory Applications
2.2 Federal Safety Standard:
MVSS 302 (49 CFR 571.302) Flammability of Interior Materials-Passenger Cars, Multipurpose Passenger Vehicles, Trucks and
3
Buses
1
This test method is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.30 on Thermal Properties.
Current edition approved May 1, 2017Dec. 1, 2019. Published June 2017January 2020. Originally approved in 1990. Last previous edition approved in 20112017 as
D5132 – 11.D5132 – 17. DOI: 10.1520/D5132-17.10.1520/D5132-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
United States Code of Federal Regulations, 49 CFR 571.302, 36 FR 28991, available from Superintendent of Documents, U.S. Government Printing Office, Washington,
DC 20402.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5132 − 19
2.3 SAE Standard:
4
SAE J369 Flammability of Polymeric Interior Materials - Horizontal Test Method
2.4 ISO Standard:
ISO 3795 Road vehicles, and tractors and machinery for agriculture and forestry—Determination of burning behavior of interior
5
materials
3. Terminology
3.1 Definitions—Terms used in this standard are defined in accordance with D883For definitions of fire-related terms , unless
otherwise specified. For terms relating to precision and bias and associated issues, the terms used in this test method, refer standard
are defined in accordance with Terminology E456to . For
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.