ASTM F1476-01
(Specification)Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
SCOPE
1.1 This standard provides the performance characteristics and qualification tests required for gasketed mechanical couplings including grooved-type mechanical couplings for grooved end pipe, mechanical restraint couplings for plain end pipe and mechanical compression couplings for plain end pipe. These couplings are for use at temperatures within the recommended temperature range of their respective gaskets. Consult manufacturer for details.
1.2 The values stated in metric units (SI) are to be regarded as the standard. The values given in parentheses (inch/pound) are provided for information purposes.
1.3 Measuring and test equipment (MTE) used in the performance of the tests described herein shall be calibrated using equipment which is traceable to the National Institute of Standards and Technology (NIST) or calibrated in accordance with the requirements detailed in BS5781 Part 1 against standards traceable to National Standards.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 As this is not a dimensional standard, nor does it contain component dimensions, the intermixing of sub-components such as gaskets and housings between manufacturers is not recommended and constitutes non-conformance with this standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1476 – 01
Standard Specification for
Performance of Gasketed Mechanical Couplings for Use in
1
Piping Applications
This standard is issued under the fixed designation F 1476; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope A153 SpecificationforZincCoating(Hot-Dip)onIronand
4
Steel Hardware
1.1 This standard provides the performance characteristics
5
A183 SpecificationforCarbonSteelTrackBoltsandNuts
and qualification tests required for gasketed mechanical cou-
A193 Specification for Alloy-Steel and Stainless Steel
plings including grooved-type mechanical couplings for
3
Bolting Materials for High-Temperature Service
grooved end pipe, mechanical restraint couplings for plain end
A194 Specification for Carbon and Alloy Steel Nuts for
pipeandmechanicalcompressioncouplingsforplainendpipe.
3
Bolts for High-Pressure and High-Temperature Service
These couplings are for use at temperatures within the recom-
A 325 Specification for Structural Bolts, Steel, Heat-
mended temperature range of their respective gaskets. Consult
6
Treated, 120/105 ksi Minimum Tensile Strength
manufacturer for details.
A395 Specification for Ferritic Ductile Iron Pressure-
1.2 The values stated in metric units (SI) are to be regarded
2
Retaining Castings for Use at Eleviated Temperatures
as the standard. The values given in parentheses (inch/pound)
2
A536 Specification for Ductile Iron Castings
are provided for information purposes.
6
A563 Specification for Carbon and Alloy Steel Nuts
1.3 Measuring and test equipment (M&TE) used in the
A 574 Specification for Alloy Steel Socket-Hand Cup
performance of the tests described herein shall be calibrated
6
Screws
using equipment which is traceable to the National Institute of
A743/A743M Specification for Castings, Iron-Chromium,
Standards and Technology (NIST) or calibrated in accordance
Iron-Chromium-Nickel, Corrosion Resistant, for General
with the requirements detailed in BS5781 Part 1 against
2
Application
standards traceable to National Standards.
B26/B26M Specification for Aluminum-Alloy Sand Cast-
1.4 This standard does not purport to address all of the
7
ings
safety concerns, if any, associated with its use. It is the
8
B88 Specification for Seamless Copper Water Tube
responsibility of the user of this standard to establish appro-
B580 Specification for Anodic Oxide Coatings on Alumi-
priate safety and health practices and determine the applica-
9
num
bility of regulatory limitations prior to use.
B633 Specification for Electrodeposited Coatings of Zinc
1.5 Asthisisnotadimensionalstandard,nordoesitcontain
9
on Iron and Steel
component dimensions, the intermixing of sub-components
D2000 Classification System for Rubber Products inAuto-
such as gaskets and housings between manufacturers is not
10
motive Applications
recommended and constitutes non-conformance with this stan-
F837 Specification for Stainless Steel Socket Head Cap
dard.
6
Screws
2. Referenced Documents
2.2 ANSI, ANSI/ASQC, or ANSI/AWWA Standards:
11
B36.10—Welded and Seamless Wrought Steel Pipe
2.1 ASTM Standards:
11
2
B36.19—Stainless Steel Pipe
A47 Specification for Ferritic Malleable Iron Castings
C151/A21.51—Ductile-Iron Pipe, Centrifugally Cast in
A53 Specification for Pipe, Steel, Black and Hot-Dipped,
3
Metal Molds or Sand-Lined Molds, for Water or Other
Zinc-Coated Welded and Seamless
11
Liquids
A135 Specification for Electric-Resistance-Welded Steel
3
Pipe
4
Annual Book of ASTM Standards, Vol 01.06.
5
Annual Book of ASTM Standards, Vol 01.04.
1 6
This specification is under the jurisdiction ofASTM Committee F25 on Ships Annual Book of ASTM Standards, Vol 15.08.
7
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on Annual Book of ASTM Standards, Vol 02.02.
8
Machinery and Piping Systems. Annual Book of ASTM Standards, Vol 02.01.
9
Current edition approved June 10, 2001. Published September 2001. Originally Annual Book of ASTM Standards, Vol 02.05.
10
published as F1476–93. Last previous edition F1476–95a. Annual Book of ASTM Standards, Vol 09.01.
2 11
Annual Book of ASTM Standards, Vol 01.02. AvailablefromAmericanNationalStandardsInstitute(ANSI),25W.43rdSt.,
3
Annual Book of ASTM Standards, Vol 01.01. 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1476 – 01
11
C606-87—Grooved and Shouldered Joints
Z1.4 Sampling Procedures and Tables for Inspection by
11
Attributes
Z540.1 Calibration Laboratori
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.