ASTM E1618-14
(Test Method)Standard Test Method for Ignitable Liquid Residues in Extracts from Fire Debris Samples by Gas Chromatography-Mass Spectrometry
Standard Test Method for Ignitable Liquid Residues in Extracts from Fire Debris Samples by Gas Chromatography-Mass Spectrometry
SIGNIFICANCE AND USE
4.1 The identification of an ignitable liquid residue in samples from a fire scene can support the field investigator's opinion regarding the origin, fuel load, and incendiary nature of the fire.
4.1.1 The identification of an ignitable liquid residue in a fire scene does not necessarily lead to the conclusion that a fire was incendiary in nature. Further investigation may reveal a legitimate reason for the presence of ignitable liquid residues.
4.1.2 Because of the volatility of ignitable liquids and variations in sampling techniques, the absence of detectable quantities of ignitable liquid residues does not necessarily lead to the conclusion that ignitable liquids were not present at the fire scene.
4.2 Materials normally found in a building, upon exposure to the heat of a fire, will form pyrolysis and combustion products. Extracted ion profiling and target compound identification techniques described herein may facilitate the identification of an ignitable liquid in the extract by reducing interference by components generated as products of pyrolysis.
SCOPE
1.1 This test method covers the identification of residues of ignitable liquids in extracts from fire debris samples. Extraction procedures are described in the referenced documents.
1.2 Although this test method is suitable for all samples, it is especially appropriate for extracts that contain high background levels of substrate materials or pyrolysis and combustion products. This test method is also suitable for the identification of single compounds, simple mixtures, or non-petroleum based ignitable liquids.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This practice cannot replace knowledge, skill, or ability acquired through appropriate education, training, and experience and should be used in conjunction with sound professional judgment.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1618 − 14
Standard Test Method for
Ignitable Liquid Residues in Extracts from Fire Debris
1
Samples by Gas Chromatography-Mass Spectrometry
This standard is issued under the fixed designation E1618; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1413 Practice for Separation of Ignitable Liquid Residues
from Fire Debris Samples by Dynamic Headspace Con-
1.1 This test method covers the identification of residues of
centration
ignitable liquids in extracts from fire debris samples. Extrac-
E2154 Practice for Separation and Concentration of Ignit-
tion procedures are described in the referenced documents.
able Liquid Residues from Fire Debris Samples by Pas-
1.2 Although this test method is suitable for all samples, it
sive Headspace Concentration with Solid Phase Microex-
is especially appropriate for extracts that contain high back-
traction (SPME)
ground levels of substrate materials or pyrolysis and combus-
E2451 Practice for Preserving Ignitable Liquids and Ignit-
tion products. This test method is also suitable for the identi-
able Liquid Residue Extracts from Fire Debris Samples
fication of single compounds, simple mixtures, or non-
petroleum based ignitable liquids.
3. Summary of Test Method
1.3 The values stated in SI units are to be regarded as
3.1 The sample is analyzed with a gas chromatograph (GC)
standard. No other units of measurement are included in this
which is interfaced to a mass spectrometer (MS) and a data
standard.
system (DS) capable of storing and manipulating chromato-
1.4 This practice cannot replace knowledge, skill, or ability
graphic and mass spectral data.
acquired through appropriate education, training, and experi-
3.2 Post-run data analysis generates extracted ion profiles
ence and should be used in conjunction with sound profes-
(mass chromatograms) characteristic of the chemical com-
sional judgment.
poundtypescommonlyfoundinignitableliquids.Additionally,
1.5 This standard does not purport to address all of the
specific chemical components (target compounds) may be
safety concerns, if any, associated with its use. It is the
identified by their mass spectra and retention times. Semi-
responsibility of the user of this standard to establish appro-
quantitative determination of target compounds which are
priate safety and health practices and determine the applica-
identified by mass spectra and retention time may be used to
bility of regulatory limitations prior to use.
develop target compound chromatograms (TCCs).
3.2.1 The total ion chromatogram (TIC), extracted ion
2. Referenced Documents
profiles (EIP) for the alkane, alkene, alcohol, aromatic,
2
2.1 ASTM Standards:
cycloalkane, ester, ketone and polynuclear aromatic compound
E1386 Practice for Separation of Ignitable Liquid Residues
types,orTCCs,orcombinationthereof,areevaluatedbyvisual
from Fire Debris Samples by Solvent Extraction
pattern matching against known reference ignitable liquids.
E1388 Practice for Sampling of HeadspaceVapors from Fire
3.2.2 Ignitable liquids may be grouped into one of seven
Debris Samples
major classifications or one miscellaneous class, as described
E1412 Practice for Separation of Ignitable Liquid Residues
in this test method.
from Fire Debris Samples by Passive Headspace Concen-
tration With Activated Charcoal
4. Significance and Use
4.1 The identification of an ignitable liquid residue in
1
ThistestmethodisunderthejurisdictionofASTMCommitteeE30onForensic
samples from a fire scene can support the field investigator’s
Sciences and is the direct responsibility of Subcommittee E30.01 on Criminalistics.
opinion regarding the origin, fuel load, and incendiary nature
Current edition approved July 1, 2014. Published July 2014. Originally approved
of the fire.
in 1994. Last previous edition approved in 2011 as E1618 – 11. DOI: 10.1520/
E1618-14.
4.1.1 The identification of an ignitable liquid residue in a
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
fire scene does not necessarily lead to the conclusion that a fire
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
was incendiary in nature. Further investigation may reveal a
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. legitimate reason for the presence of ignitable liquid residues.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1618 − 14
4.1.2 Because of the volatility of ignitable liquids and 6. Che
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E1618 − 11 E1618 − 14
Standard Test Method for
Ignitable Liquid Residues in Extracts from Fire Debris
1
Samples by Gas Chromatography-Mass Spectrometry
This standard is issued under the fixed designation E1618; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the identification of residues of ignitable liquids in extracts from fire debris samples. Extraction
procedures are described in the referenced documents.
1.2 Although this test method is suitable for all samples, it is especially appropriate for extracts that contain high background
levels of substrate materials or pyrolysis and combustion products. This test method is also suitable for the identification of single
compounds, simple mixtures, or non-petroleum based ignitable liquids.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This practice cannot replace knowledge, skill, or ability acquired through appropriate education, training, and experience
and should be used in conjunction with sound professional judgment.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E1386 Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Solvent Extraction
E1388 Practice for Sampling of Headspace Vapors from Fire Debris Samples
E1412 Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration With
Activated Charcoal
E1413 Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Dynamic Headspace Concentration
E2154 Practice for Separation and Concentration of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace
Concentration with Solid Phase Microextraction (SPME)
E2451 Practice for Preserving Ignitable Liquids and Ignitable Liquid Residue Extracts from Fire Debris Samples
3. Summary of Test Method
3.1 The sample is analyzed with a gas chromatograph (GC) which is interfaced to a mass spectrometer (MS) and a data system
(DS) capable of storing and manipulating chromatographic and mass spectral data.
3.2 Post-run data analysis generates extracted ion profiles (mass chromatograms) characteristic of the chemical compound types
commonly found in ignitable liquids. Additionally, specific chemical components (target compounds) may be identified by their
mass spectra and retention times. Semi-quantitative determination of target compounds which are identified by mass spectra and
retention time may be used to develop target compound chromatograms (TCCs).
3.2.1 The total ion chromatogram (TIC), extracted ion profiles (EIP) for the alkane, alkene, alcohol, aromatic, cycloalkane,
ester, ketone and polynuclear aromatic compound types, or TCCs, or combination thereof, are evaluated by visual pattern matching
against known reference ignitable liquids.
3.2.2 Ignitable liquids may be grouped into one of seven major classifications or one miscellaneous class, as described in this
test method.
1
This test method is under the jurisdiction of ASTM Committee E30 on Forensic Sciences and is the direct responsibility of Subcommittee E30.01 on Criminalistics.
Current edition approved June 1, 2011July 1, 2014. Published June 2011July 2014. Originally approved in 1994. Last previous edition approved in 20102011 as
E1618 – 10.E1618 – 11. DOI: 10.1520/E1618-11.10.1520/E1618-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1618 − 14
4. Significance and Use
4.1 The identification of an ignitable liquid residue in samples from a fire scene can support the field investigator’s opinion
regarding the origin, fuel load, and incendi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.