ASTM C1093-08
(Practice)Standard Practice for Accreditation of Testing Agencies for Masonry
Standard Practice for Accreditation of Testing Agencies for Masonry
SIGNIFICANCE AND USE
This practice provides the basic minimum criteria for use in evaluating the qualifications of testing agencies for masonry materials. The criteria may be supplemented by more specific criteria and requirements. It can be used as a guide for internal audits by individual users.
The intent of this practice is to provide a consensus basis for evaluating a testing agency, with respect to that agency's capability to objectively and competently provide the specific services needed by the user.
This practice may be used as a basis for accreditation.
SCOPE
1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system, and it establishes minimum qualifications for agencies engaged in the testing of masonry materials.
1.2 Criteria are provided for evaluating the capability of an agency to properly perform designated tests on masonry materials, and for establishing guidelines pertaining to an agency's organization, personnel, facilities, and quality system. This practice may be supplemented by more specific criteria and requirements for particular projects.
1.3 This practice can be used as a basis to evaluate testing agencies, and it is intended for use for the qualifying or accrediting of testing agencies, or both, public or private, engaged in the testing of masonry materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation:C1093–08
Standard Practice for
1
Accreditation of Testing Agencies for Masonry
This standard is issued under the fixed designation C1093; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* C136 Test Method for Sieve Analysis of Fine and Coarse
Aggregates
1.1 This practice covers the minimum requirements for
C140 Test Methods for Sampling and Testing Concrete
laboratorypersonnel,forestablishingandmaintainingaquality
Masonry Units and Related Units
system, and it establishes minimum qualifications for agencies
C143/C143M Test Method for Slump of Hydraulic-Cement
engaged in the testing of masonry materials.
Concrete
1.2 Criteria are provided for evaluating the capability of an
C173/C173M Test Method for Air Content of Freshly
agency to properly perform designated tests on masonry
Mixed Concrete by the Volumetric Method
materials, and for establishing guidelines pertaining to an
C185 Test Method for Air Content of Hydraulic Cement
agency’sorganization,personnel,facilities,andqualitysystem.
Mortar
This practice may be supplemented by more specific criteria
C230/C230M Specification for Flow Table for Use in Tests
and requirements for particular projects.
of Hydraulic Cement
1.3 This practice can be used as a basis to evaluate testing
C231 Test Method for Air Content of Freshly Mixed Con-
agencies, and it is intended for use for the qualifying or
crete by the Pressure Method
accrediting of testing agencies, or both, public or private,
C270 Specification for Mortar for Unit Masonry
engaged in the testing of masonry materials.
C305 Practice for Mechanical Mixing of Hydraulic Cement
1.4 This standard does not purport to address all of the
Pastes and Mortars of Plastic Consistency
safety concerns, if any, associated with its use. It is the
C470/C470M Specification for Molds for Forming Con-
responsibility of the user of this standard to establish appro-
crete Test Cylinders Vertically
priate safety and health practices and determine the applica-
C780 Test Method for Preconstruction and Construction
bility of regulatory limitations prior to use.
Evaluation of Mortars for Plain and Reinforced Unit
2. Referenced Documents
Masonry
2
C1072 Test Method for Measurement of Masonry Flexural
2.1 ASTM Standards:
Bond Strength
C67 Test Methods for Sampling and Testing Brick and
C1506 Test Method for Water Retention of Hydraulic
Structural Clay Tile
Cement-Based Mortars and Plasters
C109/C109M Test Method for Compressive Strength of
E4 Practices for Force Verification of Testing Machines
Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube
E11 SpecificationforWovenWireTestSieveClothandTest
Specimens)
Sieves
C117 TestMethodforMaterialsFinerthan75-µm(No.200)
Sieve in Mineral Aggregates by Washing
3. Terminology
3.1 Definition:
1
This practice is under the jurisdiction of ASTM Committee C15 on Manufac-
3.1.1 quality system—the organizational structure, respon-
tured Masonry Units and is the direct responsibility of Subcommittee C15.07 on
sibilities, procedures, processes, capabilities, and resources for
Standards for Laboratory Accreditation.
implementing quality management.
Current edition approved July 1, 2008. Published July 2008. Originally approved
3.2 Definitions of Terms Specific to This Standard:
in 1988. Last previous edition approved in 2007 as C1093 – 07. DOI: 10.1520/
C1093-08.
3.2.1 agency—the organization engaged to test masonry
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
materials as required by a specification or contract.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3.2.2 quality system manual (QSM)—a manual describing
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. and documenting an agency’s quality system.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1093–08
3.2.3 user—the person or organization engaging the agency stipulated under ASTM or other governing procedures and
to provide tests; or using this practice to evaluate or accredit shall be capable of evaluating the test results in terms of
the agency. specification compliance.
8. Quality System Criteria
4. Significance and Use
8.1 The agency shall establish and implement a quality
4.1 This practice provides the basic minimum criteria for
system that meets the criteria in subsections 8.2 to 8.14.
use in evaluating the qualifications of testing
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1093–07 Designation:C1093–08
Standard Practice for
1
Accreditation of Testing Agencies for Masonry
This standard is issued under the fixed designation C 1093; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system,
and it establishes minimum qualifications for agencies engaged in the testing of masonry materials.
1.2 Criteria are provided for evaluating the capability of an agency to properly perform designated tests on masonry materials,
and for establishing guidelines pertaining to an agency’s organization, personnel, facilities, and quality system. This practice may
be supplemented by more specific criteria and requirements for particular projects.
1.3 This practice can be used as a basis to evaluate testing agencies, and it is intended for use for the qualifying or accrediting
of testing agencies, or both, public or private, engaged in the testing of masonry materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C 67 Test Methods for Sampling and Testing Brick and Structural Clay Tile
C 109/C 109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C 117 Test Method for Materials Finer than 75-m (No. 200) Sieve in Mineral Aggregates by Washing
C 136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C 140 Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C 143/C 143M Test Method for Slump of Hydraulic-Cement Concrete
C 173/C 173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C 185 Test Method for Air Content of Hydraulic Cement Mortar
C 230/C 230M Specification for Flow Table for Use in Tests of Hydraulic Cement
C 231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C 270 Specification for Mortar for Unit Masonry
C 305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C 470/C 470M Specification for Molds for Forming Concrete Test Cylinders Vertically
C 780 Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry
C 1072 Test Method for Measurement of Masonry Flexural Bond Strength
C 1506 Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
E 4 Practices for Force Verification of Testing Machines
E 11 Specification for Wire Cloth and Sieves for Testing Purposes
3. Terminology
2.1
3.1 Definition:
2.1.1
3.1.1 quality system—the organizational structure, responsibilities, procedures, processes, capabilities, and resources for
implementing quality management.
2.23.2 Definitions of Terms Specific to This Standard:
1
This practice is under the jurisdiction ofASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.07 on Standards
for Laboratory Accreditation.
Current edition approved JuneJuly 1, 2007.2008. Published July 2007.2008. Originally approved in 1988. Last previous edition approved in 20062007 as C 1093 – 067.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1093–08
2.2.13.2.1 agency—the organization engaged to test masonry materials as required by a specification or contract.
2.2.2
3.2.2 quality system manual (QSM)—a manual describing and documenting an agency’s quality system.
2.2.3
3.2.3 user—the person or organization engaging the agency to provide tests; or using this practice to evaluate or accredit the
agency.
3.Significance and Use
3.1This practice provides t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.