ASTM D2241-04b
(Specification)Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
SCOPE
1.1 This specification covers poly(vinyl chloride) (PVC) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water (see appendix). Included are criteria for classifying PVC plastic pipe materials and PVC plastic pipe, a system of nomenclature for PVC plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, flattening, and extrusion quality. Methods of marking are also given.
1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.
Note 1—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Note 7.
Note 2—CPVC plastic pipe (SDR-PR), which was formerly included in this specification, is now covered by Specification F 442/F 442M.
Note 3—The sustained and burst pressure test requirements, and the pressure ratings in the appendix, are calculated from stress values obtained from tests made on pipe 4 in. (100 mm) and smaller. However, tests conducted on pipe as large as 24 in. (600 mm) in diameter have shown these stress values to be valid for larger diameter PVC pipe.
Note 4—PVC pipe made to this specification is often belled for use as line pipe. For details of the solvent cement bell, see Specification D 2672 and for details of belled elastomeric joints, see Specifications D 3139 and D 3212.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2241 – 04b
Standard Specification for
Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR
1
Series)
This standard is issued under the fixed designation D 2241; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope practices and determine the applicability of regulatory limita-
tions prior to use. A specific precautionary statement is given
1.1 This specification covers poly(vinyl chloride) (PVC)
in Note 7.
pipe made in standard thermoplastic pipe dimension ratios and
pressure rated for water (see appendix). Included are criteria
NOTE 3—CPVC plastic pipe (SDR-PR), which was formerly included
for classifying PVC plastic pipe materials and PVC plastic
in this specification, is now covered by Specification F 442/F 442M.
pipe, a system of nomenclature for PVC plastic pipe, and
NOTE 4—The sustained and burst pressure test requirements, and the
requirements and test methods for materials, workmanship,
pressureratingsintheappendix,arecalculatedfromstressvaluesobtained
dimensions, sustained pressure, burst pressure, flattening, and
from tests made on pipe 4 in. (100 mm) and smaller. However, tests
extrusion quality. Methods of marking are also given.
conducted on pipe as large as 24 in. (600 mm) in diameter have shown
1.2 The products covered by this specification are intended
these stress values to be valid for larger diameter PVC pipe.
for use with the distribution of pressurized liquids only, which
are chemically compatible with the piping materials. Due to NOTE 5—PVC pipe made to this specification is often belled for use as
line pipe. For details of the solvent cement bell, see Specification D 2672
inherent hazards associated with testing components and sys-
and for details of belled elastomeric joints, see Specifications D 3139 and
tems with compressed air or other compressed gases, some
D 3212.
manufacturersdonotallowpneumatictestingoftheirproducts.
Consult with specific product/component manufacturers for
2. Referenced Documents
their specific testing procedures prior to pneumatic testing.
2
2.1 ASTM Standards:
NOTE 1—Pressurized (compressed) air or other compressed gases
D 618 Practice for Conditioning Plastics for Testing
contain large amounts of stored energy which present serious safety
D 1598 Test Method for Time-to-Failure of Plastic Pipe
hazards should a system fail for any reason.
Under Constant Internal Pressure
NOTE 2—This standard specifies dimensional, performance and test
D 1599 Test Method for Resistance to Short-Time Hydrau-
requirements for plumbing and fluid handling applications, but does not
lic Failure Pressure of Plastic Pipe, Tubing, and Fittings
address venting of combustion gases.
D 1600 Terminology for Abbreviated Terms Relating to
1.3 The text of this specification references notes, footnotes,
Plastics
and appendixes which provide explanatory material. These
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
notesandfootnotes(excludingthoseintablesandfigures)shall
Compounds and Chlorinated Poly(Vinyl Chloride)
not be considered as requirements of the specification.
(CPVC) Compounds
1.4 The values stated in inch-pound units are to be regarded
D 2122 Test Method for Determining Dimensions of Ther-
as the standard. The values given in parentheses are for
moplastic Pipe and Fittings
information only.
D 2152 Test Method for Adequacy of Fusion of Extruded
1.5 The following safety hazards caveat pertains only to the
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
test methods portion, Section 8, of this specification: This
Acetone Immersion
standard does not purport to address all of the safety concerns,
D 2444 Test Method for Impact Resistance of Thermoplas-
if any, associated with its use. It is the responsibility of the user
tic Pipe and Fittings by Means of a Tup (Falling Weight)
of this standard to establish appropriate safety and health
D 2672 Specification for Joints for IPS PVC Pipe Using
Solvent Cement
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl 2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Based Pipe.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved Sept. 1, 2004. Published June 2004. Originally
Standards volume information, refer to the standard’s Document Summary page on
approved in 1964. Last previous edition approved in 2004 as D 2241 – 04a.
the ASTM websi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.