ASTM F3394/F3394M-20
(Specification)Standard Specification for Hardened Steel Backup and Reaction Washers Inch and Metric Dimensions
Standard Specification for Hardened Steel Backup and Reaction Washers Inch and Metric Dimensions<rangeref></rangeref >
SCOPE
1.1 This specification covers the chemical, mechanical, and dimensional requirements for hardened steel Backup and Reaction washers for use with fasteners having nominal diameters of 1/2 in. through 3 in. and M14 through M80. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, DTIs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A354, A193/A193M, A194/A194M, A320/A320M, F959/F959M, A449, A563, A563M, and F3125.
1.2 The washers are designated by style denoting the shape, by type denoting the material, and by inch or metric dimensions.
1.2.1 The styles of washers covered are:
1.2.1.1 Reaction—Circular washers with a knurled surface on one side and a contoured outside diameter designed to couple with the installation tool.
1.2.1.2 Backup—Circular washers having a knurled surface on both sides.
1.2.2 The types of washers covered are:
1.2.2.1 Type 1—Medium Carbon or Medium Carbon Alloy Steel.
1.2.2.2 Type 3—Weathering steel. This specification provides for furnishing Type 3 to chemical composition or a Corrosion Index (CRI) of 6 or higher, at the supplier’s option.
1.3 The values stated in either inch-pound units for inch fasteners and SI units for metric fasteners and are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F3394/F3394M −20
Standard Specification for
Hardened Steel Backup and Reaction Washers Inch and
1,2
Metric Dimensions
ThisstandardisissuedunderthefixeddesignationF3394/F3394M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the
1.1 This specification covers the chemical, mechanical, and
standard.
dimensional requirements for hardened steel Backup and
1.4 This standard does not purport to address all of the
Reaction washers for use with fasteners having nominal
1 safety concerns, if any, associated with its use. It is the
diameters of ⁄2 in. through 3 in. and M14 through M80. These
responsibility of the user of this standard to establish appro-
washers are intended for general-purpose mechanical and
priate safety, health, and environmental practices and deter-
structural use with bolts, nuts, studs, DTIs, and other internally
mine the applicability of regulatory limitations prior to use.
and externally threaded fasteners. These washers are suitable
1.5 This international standard was developed in accor-
for use with fasteners covered in Specifications A354, A193/
dance with internationally recognized principles on standard-
A193M, A194/A194M, A320/A320M, F959/F959M, A449,
ization established in the Decision on Principles for the
A563, A563M, and F3125.
Development of International Standards, Guides and Recom-
1.2 The washers are designated by style denoting the shape,
mendations issued by the World Trade Organization Technical
by type denoting the material, and by inch or metric dimen-
Barriers to Trade (TBT) Committee.
sions.
2. Referenced Documents
1.2.1 The styles of washers covered are:
3
1.2.1.1 Reaction—Circular washers with a knurled surface
2.1 ASTM Standards:
on one side and a contoured outside diameter designed to
A193/A193M Specification for Alloy-Steel and Stainless
couple with the installation tool.
Steel Bolting for High Temperature or High Pressure
Service and Other Special Purpose Applications
1.2.1.2 Backup—Circular washers having a knurled surface
A194/A194M Specification for Carbon Steel, Alloy Steel,
on both sides.
and Stainless Steel Nuts for Bolts for High Pressure or
1.2.2 The types of washers covered are:
High Temperature Service, or Both
1.2.2.1 Type 1—Medium Carbon or Medium Carbon Alloy
A320/A320M Specification for Alloy-Steel and Stainless
Steel.
Steel Bolting for Low-Temperature Service
1.2.2.2 Type 3—Weathering steel. This specification pro-
A354 Specification for Quenched and TemperedAlloy Steel
vides for furnishing Type 3 to chemical composition or a
Bolts, Studs, and Other Externally Threaded Fasteners
Corrosion Index (CRI) of 6 or higher, at the supplier’s option.
A449 Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile
1.3 The values stated in either inch-pound units for inch
Strength, General Use
fasteners and SI units for metric fasteners and are to be
A563 Specification for Carbon and Alloy Steel Nuts
regarded separately as standard. The values stated in each
A563M Specification for Carbon andAlloy Steel Nuts (Met-
system may not be exact equivalents; therefore, each system
4
ric) (Withdrawn 2021)
A588/A588M Specification for High-Strength Low-Alloy
Structural Steel, up to 50 ksi [345 MPa] Minimum Yield
1
This specification is under the jurisdiction of ASTM Committee F16 on
Point, with Atmospheric Corrosion Resistance
Fasteners and is the direct responsibility of Subcommittee F16.06 on Steel Washers
and Rivets.
Current edition approved Jan. 1, 2020. Published March 2020. DOI: 10.1520/
3
F3394–20 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
2
BackupandReactionwashersofthetypecoveredbythisstandardhaveapatent contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
application pending. Interested parties are invited to submit information regarding Standards volume information, refer to the standard’s Document Summary page on
the identification of an alternative(s) to these patent-pending items to the ASTM the ASTM website.
4
International Headquarters. Your comments will receive careful consideration at a The last approved version of this historical standard is referenced on
meeting of the responsible technical committee, which you may attend www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Dr
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F3394/F3394M − 20
Standard Specification for
Hardened Steel Backup and Reaction Washers Inch and
1,2
Metric Dimensions
This standard is issued under the fixed designation F3394/F3394M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the
1.1 This specification covers the chemical, mechanical, and
standard.
dimensional requirements for hardened steel Backup and
1.4 This standard does not purport to address all of the
Reaction washers for use with fasteners having nominal
safety concerns, if any, associated with its use. It is the
1
diameters of ⁄2 in. through 3 in. and M14 through M80. These
responsibility of the user of this standard to establish appro-
washers are intended for general-purpose mechanical and
priate safety, health, and environmental practices and deter-
structural use with bolts, nuts, studs, DTIs, and other internally
mine the applicability of regulatory limitations prior to use.
and externally threaded fasteners. These washers are suitable
1.5 This international standard was developed in accor-
for use with fasteners covered in Specifications A354, A193/
dance with internationally recognized principles on standard-
A193M, A194/A194M, A320/A320M, F959/F959M, A449,
ization established in the Decision on Principles for the
A563, A563M, and F3125.
Development of International Standards, Guides and Recom-
1.2 The washers are designated by style denoting the shape,
mendations issued by the World Trade Organization Technical
by type denoting the material, and by inch or metric dimen-
Barriers to Trade (TBT) Committee.
sions.
2. Referenced Documents
1.2.1 The styles of washers covered are:
3
1.2.1.1 Reaction—Circular washers with a knurled surface
2.1 ASTM Standards:
on one side and a contoured outside diameter designed to
A193/A193M Specification for Alloy-Steel and Stainless
couple with the installation tool.
Steel Bolting for High Temperature or High Pressure
Service and Other Special Purpose Applications
1.2.1.2 Backup—Circular washers having a knurled surface
A194/A194M Specification for Carbon Steel, Alloy Steel,
on both sides.
and Stainless Steel Nuts for Bolts for High Pressure or
1.2.2 The types of washers covered are:
High Temperature Service, or Both
1.2.2.1 Type 1—Medium Carbon or Medium Carbon Alloy
A320/A320M Specification for Alloy-Steel and Stainless
Steel.
Steel Bolting for Low-Temperature Service
1.2.2.2 Type 3—Weathering steel. This specification pro-
A354 Specification for Quenched and Tempered Alloy Steel
vides for furnishing Type 3 to chemical composition or a
Bolts, Studs, and Other Externally Threaded Fasteners
Corrosion Index (CRI) of 6 or higher, at the supplier’s option.
A449 Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile
1.3 The values stated in either inch-pound units for inch
Strength, General Use
fasteners and SI units for metric fasteners and are to be
A563 Specification for Carbon and Alloy Steel Nuts
regarded separately as standard. The values stated in each
A563M Specification for Carbon and Alloy Steel Nuts (Met-
system may not be exact equivalents; therefore, each system
4
ric) (Withdrawn 2021)
A588/A588M Specification for High-Strength Low-Alloy
Structural Steel, up to 50 ksi [345 MPa] Minimum Yield
1
This specification is under the jurisdiction of ASTM Committee F16 on
Point, with Atmospheric Corrosion Resistance
Fasteners and is the direct responsibility of Subcommittee F16.06 on Steel Washers
and Rivets.
Current edition approved Jan. 1, 2020. Published March 2020. DOI: 10.1520/
3
F3394–20 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
2
Backup and Reaction washers of the type covered by this standard have a patent contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
application pending. Interested parties are invited to submit information regarding Standards volume information, refer to the standard’s Document Summary page on
the identification of an alternative(s) to these patent-pending items to the ASTM the ASTM website.
4
International Headquarters. Your comments will receive careful consideration at a The last approved version of this historical standard is referenced on
meeting of the responsible technical committee, which you may attend www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.