ASTM C1139-08
(Specification)Standard Specification for Fibrous Glass Thermal Insulation and Sound Absorbing Blanket and Board for Military Applications
Standard Specification for Fibrous Glass Thermal Insulation and Sound Absorbing Blanket and Board for Military Applications
ABSTRACT
This specification covers unfaced flexible fibrous glass blanket and faced board used for thermal and sound absorbing insulation for military applications as a replacement for MIL-I-22023D. The fibrous glass felt shall be of the following types and grades: Types I and II (Grades 1, 2, 3, 4, 5, and 6). The insulation shall be composed of glass, processed from a molten state into a fibrous form, bonded with a chemical binder. The following test methods shall be performed: flexibility and rigidity; density; determining binder content; thermal conductivity; corrosiveness to steel; surface burning characteristics; determining the vibration resistance of fibrous glass insulation; maximum use temperature; and determination of flashover potential of a lining material using a quarter-scale room fire test.
SCOPE
1.1 This specification covers unfaced flexible fibrous glass blanket and faced board used for thermal and sound absorbing insulation at temperatures up to 450°F (232°C) for military applications as a replacement for MIL-I-22023D.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This specification measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4 The following hazard caveat pertains only to the test method section of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1139 −08
StandardSpecification for
Fibrous Glass Thermal Insulation and Sound Absorbing
1
Blanket and Board for Military Applications
This standard is issued under the fixed designation C1139; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C411 Test Method for Hot-Surface Performance of High-
Temperature Thermal Insulation
1.1 This specification covers unfaced flexible fibrous glass
C423 Test Method for SoundAbsorption and SoundAbsorp-
blanket and faced board used for thermal and sound absorbing
tion Coefficients by the Reverberation Room Method
insulation at temperatures up to 450°F (232°C) for military
C518 Test Method for Steady-State Thermal Transmission
applications as a replacement for MIL-I-22023D.
Properties by Means of the Heat Flow Meter Apparatus
1.2 The values stated in inch-pound units are to be regarded
C612 Specification for Mineral Fiber Block and Board
as standard. The values given in parentheses are mathematical
Thermal Insulation
conversions to SI units that are provided for information only
C665 Specification for Mineral-Fiber Blanket Thermal Insu-
and are not considered standard.
lation for Light Frame Construction and Manufactured
1.3 This specification measures and describes the response Housing
C1101/C1101M Test Methods for Classifying the Flexibility
of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all or Rigidity of Mineral Fiber Blanket and Board Insulation
E84 Test Method for Surface Burning Characteristics of
factors required for fire hazard or fire risk assessment of the
materials, products, or assemblies under actual fire conditions. Building Materials
E176 Terminology of Fire Standards
1.4 The following hazard caveat pertains only to the test
E2231 Practice for Specimen Preparation and Mounting of
method section of this specification. This standard does not
Pipe and Duct Insulation Materials to Assess Surface
purport to address all of the safety concerns, if any, associated
Burning Characteristics
with its use. It is the responsibility of the user of this standard
2.2 U.S. Military Standards:
to establish appropriate safety and health practices and
MIL-STD-167-1 Mechanical Vibrations of Shipboard
determine the applicability of regulatory limitations prior to
Equipment (Type 1 Environmental and Type II Internally
use.
3
Excited)
3
2. Referenced Documents MIL-Y-1140 Yarn, Cord, Sleeving, Cloth and Tape-Glass
3
MIL-A-3316 Adhesives, Fire Resistant, Thermal Insulation
2
2.1 ASTM Standards:
C167 Test Methods for Thickness and Density of Blanket or
3. Terminology
Batt Thermal Insulations
3.1 Definitions—Terminology C168 and Terminology E176
C168 Terminology Relating to Thermal Insulation
shall apply to the terms used in this specification.
C177 Test Method for Steady-State Heat Flux Measure-
ments and Thermal Transmission Properties by Means of
4. Classification
the Guarded-Hot-Plate Apparatus
4.1 The fibrous glass felt shall be of the following types and
C390 Practice for Sampling and Acceptance of Thermal
grades:
Insulation Lots
3 3
Type I, Unfaced Thermal Blanket Nominal Density, lb/ft (kg/m )
Grade 1 0.75 (12)
1
Grade 2 1.00 (16)
This specification is under the jurisdiction of ASTM Committee C16 on
Grade 3 1.50 (24)
Thermal Insulation and is the direct responsibility of Subcommittee C16.23 on
Grade 4 2.00 (32)
Blanket and Loose Fill Insulation.
Grade 5 2.50 (40)
Current edition approved Oct. 1, 2008. Published November 2008. Originally
Grade 6 3.00 (48)
approvedin1990.Lastpreviouseditionapprovedin2002asC1139–90(2002).DOI:
10.1520/C1139-08.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1139−08
7.7 Surface Burning Characteristics Type I and II—The
Type II, Unfaced Sound Absorbing
3 3
Blanket Nominal Density, lb/ft (kg/m )
insulation shall have a flame spread index not greater than 25
Grade 1 0.75 (12)
and a smoke developed index not greater than 50 when tested
Grade 2 1.00 (16)
in accordance with 11.7.
Grade 3 1.50 (24)
Grade 4 2.00 (32)
7.8 Quarter Scale Room Fire Test
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1139–90(Reapproved 2002) Designation: C 1139 – 08
Standard Specification for
Fibrous Glass Thermal Insulation and Sound Absorbing
1
Blanket and Board for Military Applications
This standard is issued under the fixed designation C 1139; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers unfaced flexible fibrous glass blanket and faced board used for thermal and sound absorbing
insulation at temperatures up to 450°F (232°C) for military applications as a replacement for MIL-I-22023D.
1.2The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This specification measures and describes the response of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials,
products, or assemblies under actual fire conditions.
1.4 The following hazard caveat pertains only to the test method section of this specification. This standard does not purport
to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C 167 Test Methods for Thickness and Density of BlanketsBlanket or Batt Thermal Insulations
C 168 Terminology Relating to Thermal Insulation
C 177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C 390 CriteriaPractice for Sampling and Acceptance of Preformed Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C 423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C 518 Test Method for Steady-State Heat Flux Measurements andThermalTransmission Properties by Means of the Heat Flow
Meter Apparatus
C 612 Specification for Mineral Fiber Block and Board Thermal Insulation
C 665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C 1101/C 1101M Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation
E84 Test Method for Surface Burning Characteristics of Building Materials Test Method for Surface Burning Characteristics
of Building Materials
E 176 Terminology of Fire Standards
E 2231 Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning
Characteristics
2.2 U.S. Military Standards:
3
MIL-STD-167-1 Mechanical Vibrations of Shipboard Equipment (Type 1 Environmental and Type II Internally Excited)
3
MIL-Y-1140 Yarn, Cord, Sleeving, Cloth and Tape-Glass
1
ThisspecificationisunderthejurisdictionofASTMCommitteeC16onThermalInsulationandisthedirectresponsibilityofSubcommitteeC16.23onBlanketandLoose
Fill Insulation.
Current edition approved Feb. 23, 1990. Published August 1990.
Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1990. Last previous edition approved in 2002 as C 1139–90(2002).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 04.06.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 04.07.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1139–08
3
MIL-A-3316 Adhesives, Fire Resistant, Thermal Insulation
3. Terminology
3.1 Definitions—Terminology C 168 and Terminology E 176 shall apply to the terms u
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1139–90(Reapproved 2002) Designation: C 1139 – 08
Standard Specification for
Fibrous Glass Thermal Insulation and Sound Absorbing
1
Blanket and Board for Military Applications
This standard is issued under the fixed designation C 1139; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers unfaced flexible fibrous glass blanket and faced board used for thermal and sound absorbing
insulation at temperatures up to 450°F (232°C) for military applications as a replacement for MIL-I-22023D.
1.2The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This specification measures and describes the response of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials,
products, or assemblies under actual fire conditions.
1.4 The following hazard caveat pertains only to the test method section of this specification. This standard does not purport
to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C 167 Test Methods for Thickness and Density of BlanketsBlanket or Batt Thermal Insulations
C 168 Terminology Relating to Thermal Insulation
C 177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C 390 CriteriaPractice for Sampling and Acceptance of Preformed Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C 423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C 518 Test Method for Steady-State Heat Flux Measurements andThermalTransmission Properties by Means of the Heat Flow
Meter Apparatus
C 612 Specification for Mineral Fiber Block and Board Thermal Insulation
C 665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C 1101/C 1101M Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation
E84 Test Method for Surface Burning Characteristics of Building Materials Test Method for Surface Burning Characteristics
of Building Materials
E 176 Terminology of Fire Standards
E 2231 Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning
Characteristics
2.2 U.S. Military Standards:
3
MIL-STD-167-1 Mechanical Vibrations of Shipboard Equipment (Type 1 Environmental and Type II Internally Excited)
3
MIL-Y-1140 Yarn, Cord, Sleeving, Cloth and Tape-Glass
1
ThisspecificationisunderthejurisdictionofASTMCommitteeC16onThermalInsulationandisthedirectresponsibilityofSubcommitteeC16.23onBlanketandLoose
Fill Insulation.
Current edition approved Feb. 23, 1990. Published August 1990.
Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1990. Last previous edition approved in 2002 as C 1139–90(2002).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 04.06.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 04.07.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1139–08
3
MIL-A-3316 Adhesives, Fire Resistant, Thermal Insulation
3. Terminology
3.1 Definitions—Terminology C 168 and Terminology E 176 shall apply to the terms u
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.