ASTM C1014-17
(Specification)Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
ABSTRACT
This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water. The basic material shall be fibers made form mineral substances such as rock, slag or glass processed from the molten state into a fibrous form. All self-supporting applications of the insulation shall have a minimum adhesive/cohesive strength of five times the weight of the material under the testing plate when tested. The insulation shall not spall, crack, or delaminate when the substrate is deflected. The insulation shall have a maximum flame spread index of 25 and a maximum smoke developed of 50 when tested. The insulation shall have a weight loss not greater than 5 %, nor shall there be a flaming ignition when tested. When tested, the insulation shall have growth no greater than that observed on the white birch tongue depressor comparative material. The spray-applied mineral fiber shall show no greater corrosion than the comparative plate in contact with the sterile cotton for the particular metal substrate to which classification is desired. A detectable odor of a strong objectionable nature recorded by more than two of the five panel members shall constitute rejection of the material when tested. Density and thickness of each sample tested shall be determined in accordance with test methods E 605. The adhesive/cohesive strength, thermal resistance, effects of substrate deflection, water vapor sorption, surface burning characteristics, smoldering combustion, fungi resistance, particular metal substrate corrosion, sound absorption, odor emission, and air errosion characteristics shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation.
1.2 These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water.
1.3 The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions.
1.4 This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1014 −17
Standard Specification for
Spray-Applied Mineral Fiber Thermal and Sound Absorbing
1
Insulation
This standard is issued under the fixed designation C1014; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C423 Test Method for SoundAbsorption and SoundAbsorp-
tion Coefficients by the Reverberation Room Method
1.1 This specification covers the composition and the physi-
C518 Test Method for Steady-State Thermal Transmission
cal properties of spray-applied mineral fiber thermal and sound
Properties by Means of the Heat Flow Meter Apparatus
absorbing insulation.
C665 Specification for Mineral-Fiber Blanket Thermal Insu-
1.2 These mineral fibers shall be pneumatically conveyed to
lation for Light Frame Construction and Manufactured
a spray nozzle where they are mixed with water.These mineral
Housing
fibers shall have a binder either pre-mixed with the fibers or
C1104/C1104M Test Method for Determining the Water
added at the spray nozzle with the water.
Vapor Sorption of Unfaced Mineral Fiber Insulation
1.3 The spray-applied mineral fiber insulation is intended C1114 Test Method for Steady-State Thermal Transmission
for use in building constructions at ambient conditions.
Properties by Means of the Thin-Heater Apparatus
C1149 Specification for Self-Supported Spray Applied Cel-
1.4 This is a material specification only and is not intended
lulosic Thermal Insulation
to cover methods of application that are supplied by the
C1304 Test Method for Assessing the Odor Emission of
manufacturer.
Thermal Insulation Materials
1.5 The values stated in inch-pound units are to be regarded
C1338 Test Method for Determining Fungi Resistance of
as standard. The values given in parentheses are mathematical
Insulation Materials and Facings
conversions to SI units that are provided for information only
C1368 Test Method for Determination of Slow Crack
and are not considered standard.
Growth Parameters of Advanced Ceramics by Constant
1.6 This standard does not purport to address all of the
Stress-Rate Strength Testing at Ambient Temperature
safety concerns, if any, associated with its use. It is the
E84 Test Method for Surface Burning Characteristics of
responsibility of the user of this standard to establish appro-
Building Materials
priate safety and health practices and determine the applica-
E605 Test Methods for Thickness and Density of Sprayed
bility of regulatory limitations prior to use.
Fire-Resistive Material (SFRM) Applied to Structural
Members
2. Referenced Documents
E736 Test Method for Cohesion/Adhesion of Sprayed Fire-
2
2.1 ASTM Standards:
Resistive Materials Applied to Structural Members
C168 Terminology Relating to Thermal Insulation
E759 Test Method for Effect of Deflection on Sprayed
C177 Test Method for Steady-State Heat Flux Measure-
Fire-Resistive Material Applied to Structural Members
ments and Thermal Transmission Properties by Means of
E795 Practices for Mounting Test Specimens During Sound
the Guarded-Hot-Plate Apparatus
Absorption Tests
C390 Practice for Sampling and Acceptance of Thermal
E859 Test Method forAir Erosion of Sprayed Fire-Resistive
Insulation Lots
Materials (SFRMs) Applied to Structural Members
3. Terminology
1
This specification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.23 on
3.1 Definitions—For definitions of terms used in this
Blanket and Loose Fill Insulation.
specification, see Terminology C168.
Current edition approved March 1, 2017. Published March 2017. Originally
3.2 Definitions of Terms Specific to This Standard:
approved in 1984. Last previous edition approved in 2013 as C1014 – 08 (2013).
DOI: 10.1520/C1014-17.
3.2.1 constant mass—the mass of a sample at equilibrium
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
conditions of 75 6 5°F (23 6 5°C) and 50 6 5 % relative
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
humidity that shall not deviate more than 0.5 % over a 24-h
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. period.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1014 − 17
3.2.2 cured—the state or condition of the finished product 6.2 The thickness and the appearance of the insulation sh
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1014 − 08 (Reapproved 2013) C1014 − 17
Standard Specification for
Spray-Applied Mineral Fiber Thermal and Sound Absorbing
1
Insulation
This standard is issued under the fixed designation C1014; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound
absorbing insulation.
1.2 These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral
fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water.
1.3 The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions.
1.4 This is a material specification only and is not intended to cover methods of application that are supplied by the
manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C1104/C1104M Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
C1114 Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
C1149 Specification for Self-Supported Spray Applied Cellulosic Thermal Insulation
C1304 Test Method for Assessing the Odor Emission of Thermal Insulation Materials
C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1368 Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate
Strength Testing at Ambient Temperature
E84 Test Method for Surface Burning Characteristics of Building Materials
E605 Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members
E756E736 Test Method for Measuring Vibration-Damping Properties of MaterialsCohesion/Adhesion of Sprayed Fire-Resistive
Materials Applied to Structural Members
E759 Test Method for Effect of Deflection on Sprayed Fire-Resistive Material Applied to Structural Members
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.23 on Blanket and Loose
Fill Insulation.
Current edition approved March 1, 2013March 1, 2017. Published March 2013March 2017. Originally approved in 1984. Last previous edition approved in 20082013 as
C1014C1014 – 08 (2013).–08. DOI: 10.1520/C1014-08R13.10.1520/C1014-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1014 − 17
E795 Practices for Mounting Test Specimens During Sound Absorption Tests
E859 Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members
3. Terminology
3.1 Definitions—For definitions of terms used in this specification, see Terminology C168.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 constant mass—the mass of a sample at
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.