ASTM D3212-21
(Specification)Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ABSTRACT
This specification covers joints for plastic pipe systems intended for drain, and gravity sewerage pipe at internal or external pressures less than a certain ft. head using flexible watertight elastomeric seals. The joints are classified into two types based on effecting watertightness through compression of an elastomeric seal or ring: push-on-joint is a joint in which an elastomeric ring gasket is compressed in the annular space between a bell end or socket and a spigot end of pipe and mechanical joint is a joint made using mechanical means or devices to develop a pressure seal. Joints shall not leak when subjected to the internal and external hydrostatic tests. All surfaces of the joint upon or against which the gasket bears shall be smooth and free of cracks, fractures, or imperfections. The gasket shall be the sole element depended upon to make the joint flexible and watertight. The gasket shall be a continuous elastomeric ring. In mechanical joints, the pipe spigot shall have a wall thickness sufficient to withstand, without deformation or collapse, the compressive force exerted when the fitting is tightened. Some joint designs provide for the angular deflection of a pipe joint, without reducing watertightness. Where greater deflections are required than permitted by the joint design, suitable fittings must be provided. The joint components shall be of such design that they will withstand the forces caused by the compression of the gasket when joined without cracking or fracturing when tested. Dimensions of joint components and gaskets shall meet the requirements specified. Test methods such as internal pressure test and vacuum test shall be performed.
SCOPE
1.1 This specification covers joints for plastic pipe systems intended for drain, and gravity sewerage pipe at internal or external pressures less than 25-ft head using flexible watertight elastomeric seals. This specification is intended to cover the test requirements, test methods, and acceptable materials. The test methods described for the joints are not intended to be routine quality control tests but to be reliability or performance requirements.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The following safety hazards caveat pertains only to the test method portion, paragraph 7.5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3212 −21 An American National Standard
Standard Specification for
Joints for Drain and Sewer Plastic Pipes Using Flexible
1
Elastomeric Seals
This standard is issued under the fixed designation D3212; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* F477 Specification for Elastomeric Seals (Gaskets) for Join-
ing Plastic Pipe
1.1 This specification covers joints for plastic pipe systems
F913 Specification for Thermoplastic Elastomeric Seals
intended for drain, and gravity sewerage pipe at internal or
(Gaskets) for Joining Plastic Pipe
external pressures less than 25-ft head using flexible watertight
elastomeric seals. This specification is intended to cover the
3. Types
test requirements, test methods, and acceptable materials. The
3.1 This specification covers two types of joints based on
test methods described for the joints are not intended to be
effectingwatertightnessthroughcompressionofanelastomeric
routine quality control tests but to be reliability or performance
seal or ring:
requirements.
3.1.1 Push-on Joint—A joint in which an elastomeric ring
1.2 The text of this specification references notes, footnotes,
gasket is compressed in the annular space between a bell end
and appendixes which provide explanatory material. These
or socket and a spigot end of pipe.
notesandfootnotes(excludingthoseintablesandfigures)shall
3.1.2 Mechanical Joint—A joint made using mechanical
not be considered as requirements of the specification.
means or devices to develop a pressure seal.
1.3 The following safety hazards caveat pertains only to the
4. Materials
test method portion, paragraph 7.5, of this specification: This
4.1 Material used for elastomeric seal in push-on joints
standarddoesnotpurporttoaddressallofthesafetyconcerns,
shall meet the requirements of either Specification F477 or
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser
F913.
of this standard to establish appropriate safety, health, and
environmental practices and determine the applicability of
4.2 Lubricant, if required, shall be suitable for lubricating
regulatory limitations prior to use.
the parts of the joints in the assembly. The lubricant shall have
1.4 This international standard was developed in accor-
no deteriorating effects on the gasket and pipe materials.
dance with internationally recognized principles on standard-
5. General Requirements
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- 5.1 Joints shall not leak when subjected to the internal and
mendations issued by the World Trade Organization Technical
external hydrostatic tests of Section 7 for a period of 10 min.
Barriers to Trade (TBT) Committee.
5.2 All surfaces of the joint upon or against which the
gasket bears shall be smooth and free of cracks, fractures, or
2. Referenced Documents
imperfections.
2
2.1 ASTM Standards:
5.3 Drawings—The manufacturer shall furnish drawings of
D2122 Test Method for Determining Dimensions of Ther-
the joint and gasket if requested by the purchaser.
moplastic Pipe and Fittings
5.4 The gasket shall be the sole element depended upon to
make the joint flexible and watertight. The gasket shall be a
continuous elastomeric ring.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
5.5 In mechanical joints, the pipe spigot shall have a wall
Current edition approved Dec. 1, 2021. Published March 2022. Originally
thickness sufficient to withstand, without deformation or
approved in 1973. Last previous edition approved in 2020 as D3212 – 20 DOI:
collapse, the compressive force exerted when the fitting is
10.1520/D3212-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or tightened.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5.6 Some joint designs provide for the angular deflection of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. a pipe joint, without reducing watertightness. Where greater
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 -------------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3212 − 20 D3212 − 21 An American National Standard
Standard Specification for
Joints for Drain and Sewer Plastic Pipes Using Flexible
1
Elastomeric Seals
This standard is issued under the fixed designation D3212; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers joints for plastic pipe systems intended for drain, and gravity sewerage pipe at internal or external
pressures less than 25-ft head using flexible watertight elastomeric seals. This specification is intended to cover the test
requirements, test methods, and acceptable materials. The test methods described for the joints are not intended to be routine
quality control tests but to be reliability or performance requirements.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The following safety hazards caveat pertains only to the test method portion, paragraph 7.5, of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F1674 Test Method for Joint Restraint Products for Use with PVC Pipe
3. Types
3.1 This specification covers two types of joints based on effecting watertightness through compression of an elastomeric seal or
ring:
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
Current edition approved Nov. 15, 2020Dec. 1, 2021. Published December 2020March 2022. Originally approved in 1973. Last previous edition approved in 2020 as
D3212 – 07D3212 – 20(2020). DOI: 10.1520/D3212-20.10.1520/D3212-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3212 − 21
3.1.1 Push-on Joint—A joint in which an elastomeric ring gasket is compressed in the annular space between a bell end or socket
and a spigot end of pipe.
3.1.2 Mechanical Joint—A joint made using mechanical means or devices to develop a pressure seal.
4. Materials
4.1 Material used for elastomeric seal in push-on joints shall meet the requirements of either Specification F477 or F913.
4.2 Lubricant, if required, shall be suitable for lubricating the parts of the joints in the assembly. The lubricant shall have no
deteriorating effects on the gasket and pipe materials.
5. General Requirements
5.1 Joints shall not leak when subjected to the internal and external hydrostatic tests of Section 7 for a period of 10 min.
5.2 All surfaces of the joint upon or against which the gasket bears shall be smooth and free of cracks, fractures, or imperfections.
5.3 Drawings—The manufacturer shall furnish drawings of the joint and gasket if requested by the purchaser.
5.4 The gasket shall be the sole element depended upon to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.