ASTM A193/A193M-00b

Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service

SCOPE
1.1 This specification covers alloy and stainless steel bolting material for pressure vessels, valves, flanges, and fittings for high-temperature service. The term  bolting material as used in this specification covers bars, bolts, screws, studs, stud bolts, and wire. Bars and wire shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened. When strain hardened austenitic steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood.
1.2 Several grades are covered, including ferritic steels and austenitic stainless steels designated B5, B8, and so forth. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics.
Note 1—The committee formulating this specification has included fifteen steel types that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent.Note 2—For grades of alloy-steel bolting material suitable for use at the lower range of high-temperature applications, reference should be made to Specification A354.
Note 3—For grades of alloy-steel bolting material suitable for use in low-temperature applications, reference should be made to Specification A320/A320M.
1.3 Nuts for use with this bolting material are covered in Section 13.
1.4 Supplementary Requirements S1 through S10 are provided for use when additional tests or inspection are desired. These shall apply only when specified in the purchase order.
1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable M specification designation (SI units), the material shall be furnished to inch-pound units.
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

General Information

• Status: Historical
• Publication Date: 09-Oct-2001
• ICS: 21.060.01 - Fasteners in general
• ICS: 77.080.20 - Steels
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.22 - Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications

Relations

• Replaces: ASTM A193/A193M-00a - Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
• Effective Date: 10-Oct-2001
• Replaced By: ASTM A193/A193M-01 - Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1370-92(2019)e1 - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
• Effective Date: 10-Oct-2001
• Referred By: ASTM A962/A962M-23a - Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1476-07(2019) - Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1565-00(2019) - Standard Specification for Pressure-Reducing Valves for Steam Service
• Effective Date: 10-Oct-2001
• Referred By: ASTM C1533-15(2022) - Standard Guide for General Design Considerations for Hot Cell Equipment
• Effective Date: 10-Oct-2001
• Referred By: ASTM F2437/F2437M-17 - Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs
• Effective Date: 10-Oct-2001
• Referred By: ASTM F3394/F3394M-20 - Standard Specification for Hardened Steel Backup and Reaction Washers Inch and Metric Dimensions<rangeref></rangeref >
• Effective Date: 10-Oct-2001
• Referred By: ASTM B994/B994M-22 - Standard Specification for Nickel-Cobalt Alloy Coating
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1510-21 - Standard Specification for Rotary Positive Displacement Pumps, Ships Use
• Effective Date: 10-Oct-2001
• Referred By: ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
• Effective Date: 10-Oct-2001
• Referred By: ASTM C852/C852M-17(2022) - Standard Guide for Design Criteria for Plutonium Gloveboxes
• Effective Date: 10-Oct-2001
• Referred By: ASTM F998-12(2022) - Standard Specification for Centrifugal Pump, Shipboard Use
• Effective Date: 10-Oct-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A 193/A 193M – 00b An American National Standard
Standard Specification for
Alloy-Steel and Stainless Steel Bolting Materials for High-
1
Temperature Service
This standard is issued under the fixed designation A 193/A 193M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 1.6 The values stated in either inch-pound units or SI units
2
are to be regarded separately as standard. Within the text, the
1.1 This specification covers alloy and stainless steel bolt-
SI units are shown in brackets. The values stated in each
ing material for pressure vessels, valves, flanges, and fittings
system are not exact equivalents; therefore, each system must
for high-temperature service. The term bolting material as used
be used independently of the other. Combining values from the
in this specification covers bars, bolts, screws, studs, stud bolts,
two systems may result in nonconformance with the specifi-
and wire. Bars and wire shall be hot-wrought. The material
cation.
may be further processed by centerless grinding or by cold
drawing. Austenitic stainless steel may be carbide solution
2. Referenced Documents
treated or carbide solution treated and strain-hardened. When
2.1 ASTM Standards:
strain hardened austenitic steel is ordered, the purchaser should
A 194/A 194M Specification for Carbon and Alloy Steel
take special care to ensure that Appendix X1 is thoroughly
Nuts for Bolts for High-Pressure or High-Temperature
understood.
3
Service, or Both
1.2 Several grades are covered, including ferritic steels and
A 320/A 320M Specification for Alloy/Steel Bolting Mate-
austenitic stainless steels designated B5, B8, and so forth.
3
rials for Low-Temperature Service
Selection will depend upon design, service conditions, me-
A 354 Specification for Quenched and Tempered Alloy
chanical properties, and high-temperature characteristics.
Steel Bolts, Studs, and Other Externally Threaded Fasten-
NOTE 1—The committee formulating this specification has included 4
ers
fifteen steel types that have been rather extensively used for the present
A 962/A 962M Specification for Common Requirements
purpose. Other compositions will be considered for inclusion by the
for Steel Fasteners or Fastener Materials, or Both, Intended
committee from time to time as the need becomes apparent.
for Use at Any Temperature from Cryogenic to the Creep
NOTE 2—For grades of alloy-steel bolting material suitable for use at
3
Range
the lower range of high-temperature applications, reference should be
made to Specification A 354.
E 18 Test Methods for Rockwell Hardness and Rockwell
5
NOTE 3—For grades of alloy-steel bolting material suitable for use in
Superficial Hardness of Metallic Materials
low-temperature applications, reference should be made to Specification
E 21 Test Methods for Elevated Temperature Tension Tests
A 320/A 320M.
5
of Metallic Materials
1.3 Nuts for use with this bolting material are covered in
E 112 Test Methods for Determining the Average Grain
5
Section 13.
Size
1.4 Supplementary Requirements S1 through S10 are pro-
E 139 Test Methods for Conducting Creep, Creep-Rupture,
5
vided for use when additional tests or inspection are desired.
and Stress-Rupture Tests of Metallic Materials
These shall apply only when specified in the purchase order.
E 150 Practice for Conducting Creep and Creep-Rupture
1.5 This specification is expressed in both inch-pound units
Tension Tests of Metallic Materials Under Conditions of
6
and in SI units. However, unless the order specifies the
Rapid Heating and Short Times
applicable M specification designation (SI units), the material
E 151 Practice for Tension Tests of Metallic Materials at
shall be furnished to inch-pound units.
Elevated Temperatures with Rapid Heating and Conven-
6
tional or Rapid Strain Rates
E 292 Test Methods for Conducting Time-for-Rupture
1
5
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Notch Tension Tests of Materials
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
A01.22 on Steel Forgings and Wrought Fittings for Piping Applications and Bolting
Materials for Piping and Special Purpose Applications.
3
Current edition approved Dec. 10, 2000. Published February 2001. Originally Annual Book of ASTM Standards, Vol 01.01.
4
published as A 193 – 36 T. Last previous edition A 193/A 193M – 00a. Annual Book of ASTM Standards, Vol 01.08.
2 5
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- Annual Book of ASTM Stand
...