ASTM E999-10
(Guide)Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
SIGNIFICANCE AND USE
The provisions in this guide are intended to control the reliability or quality of the image development process only. The acceptability or quality of industrial radiographic films processed in this manner as well as the materials or products radiographed remain at the discretion of the user, or inspector, or both. It is further intended that this guide be used as an adjunct to and not a replacement for Guide E94.
SCOPE
1.1 This guide establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial radiographic film processing.
1.2 Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for wet-chemical processes and dry processing techniques.
1.3 The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent, on the degree to which a facility adheres to good processing practices as a matter of routine procedure.
1.4 If a nondestructive testing agency as described in Practice E543 is used to perform the examination, the testing agency shall meet the requirements of Practice E543.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of federal and local codes prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E999 − 10
StandardGuide for
Controlling the Quality of Industrial Radiographic Film
1
Processing
This standard is issued under the fixed designation E999; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1254 Guide for Storage of Radiographs and Unexposed
2 Industrial Radiographic Films
1.1 This guide establishes guidelines that may be used for
E1316 Terminology for Nondestructive Examinations
the control and maintenance of industrial radiographic film
4
2.2 ISO Standards:
processing equipment and materials. Effective use of these
ISO 11699-2 Nondestructive testing—Industrial Radio-
guidelines aid in controlling the consistency and quality of
graphic Film. Part 2: Control of film processing by means
industrial radiographic film processing.
of references values.
1.2 Use of this guide is limited to the processing of films for
ISO 18917 Photography—Determinationofresidualthiosul-
industrial radiography. This guide includes procedures for
fateandotherrelatedchemicalsinprocessedphotographic
wet-chemical processes and dry processing techniques.
materials—Methods using iodine amylase, methylene
1.3 The necessity of applying specific control procedures
blue, and silver sulfide
such as those described in this guide is dependent, to a certain
2.3 CEN Standards:
extent, on the degree to which a facility adheres to good
EN 584-2 Nondestructive Testing—Industrial Radiographic
processing practices as a matter of routine procedure.
Film. Part 2: Control of film processing by means of
4
reference values
1.4 If a nondestructive testing agency as described in
2.4 ANSI Standards:
Practice E543 is used to perform the examination, the testing
IT 2.26 Photography—Photographic Materials– Determina-
agency shall meet the requirements of Practice E543.
4
tion of Safelight Conditions
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to establish appro-
3.1 Definitions—For definitions of terms used in this guide,
priate safety, health, and environmental practices and deter-
see Terminology E1316.
mine the applicability of federal and local codes prior to use.
4. Significance and Use
2. Referenced Documents
4.1 The provisions in this guide are intended to control the
3
2.1 ASTM Standards:
reliability or quality of the image development process only.
E94 Guide for Radiographic Examination
The acceptability or quality of industrial radiographic films
E543 Specification forAgencies Performing Nondestructive
processed in this manner as well as the materials or products
Testing
radiographed remain at the discretion of the user, or inspector,
E1079 Practice for Calibration of Transmission Densitom-
or both. It is further intended that this guide be used as an
eters
adjunct to and not a replacement for Guide E94.
5. Chemical Mixing for Manual and Automatic Processes
1
This guide is under the jurisdiction of ASTM Committee E07 on Nondestruc-
5.1 Any equipment that comes in contact with processing
tive Testing and is the direct responsibility of Subcommittee E07.01 on Radiology
solutions should be made of glass, hard rubber, polyethylene,
(X and Gamma) Method.
PVC, enameled steel, stainless steel, or other chemically inert
CurrenteditionapprovedJune1,2010.PublishedJuly2010.Originallyapproved
in1990.Lastpreviouseditionapprovedin2005asE999 - 05.DOI:10.1520/E0999-
materials. This includes materials such as plumbing, mixing
10.
impellers, and the cores of filter cartridges. Do not allow
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
materials such as tin, copper, steel, brass, aluminum, or zinc to
cation SE-999 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E999 − 10
come into contact with processing solutions. These materials 6.2 In Replenisher or Process Tanks—Wherever possible,
can cause solution contamination that may result in film protect solutions in tanks with floating lids and dust covers. In
fogging or rapid oxidation. addition to preventing conta
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E999–05 Designation:E999–10
Standard Guide for
Controlling the Quality of Industrial Radiographic Film
1
Processing
This standard is issued under the fixed designation E999; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This guide establishes guidelines that may be used for the control and maintenance of industrial radiographic film
processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial
radiographic film processing.
1.2 Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for
wet-chemical processes and dry processing techniques.
1.3 The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent,
on the degree to which a facility adheres to good processing practices as a matter of routine procedure.
1.4 If a nondestructive testing agency as described in Practice E543 is used to perform the examination, the testing agency shall
meet the requirements of Practice E543.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
federal and local codes prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
E94 Guide for Radiographic Examination
E543 Specification for Agencies Performing Nondestructive Testing
E1079 Practice for Calibration of Transmission Densitometers
E1254 Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
E1316 Terminology for Nondestructive Examinations
4
2.2 ANSI Standard: ISO Standards:
ANSI PH 4.8Methylene Blue Method for Measuring Thiosulfate and Silver Densitometric Method for Measuring Residual
Chemicals in Films, Plates, and Papers ISO 11699-2 Nondestructive testing—Industrial Radiographic Film. Part 2: Control
of film processing by means of references values.
ISO 18917 Photography—Determination of residual thiosulfate and other related chemicals in processed photographic
materials—Methods using iodine amylase, methylene blue, and silver sulfide
2.3 CEN Standards:
EN 584-2 Nondestructive Testing—Industrial Radiographic Film. Part 2: Control of film processing by means of reference
4
values
2.4 ANSI Standards:
4
IT 2.26 Photography—Photographic Materials– Determination of Safelight Conditions
3. Terminology
3.1 Definitions—For definitions of terms used in this guide, see Terminology E1316.
1
This guide is under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.01 on Radiology (X and
Gamma) Method.
Current edition approved June 1, 2005.2010. Published June 2005.July 2010. Originally approved in 1990. Last previous edition approved in 19992005 as
E999-99.E999 - 05. DOI: 10.1520/E0999-105.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SE-999 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E999–10
4. Significance and Use
4.1 The provisions in this guide are intended to control the reliability or quality of the image development process only. The
acceptability or quality of industrial radiographic films processed in this manner as well as the materials or products radiographed
remain at the discretion of the user, or inspector, or both. It is further intended that this guide be used as an adjunct to and not a
replacement for Guide E94.
5. Chemical Mixing for Manual and Automatic Processes
5.1 Any equipment that comes in contact with processing solutions should be made of glass, hard rubber, polyethylene, PVC,
enameledsteel,stainlesssteel,oroth
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E999–05 Designation:E999–10
Standard Guide for
Controlling the Quality of Industrial Radiographic Film
1
Processing
This standard is issued under the fixed designation E999; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This guide establishes guidelines that may be used for the control and maintenance of industrial radiographic film
processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial
radiographic film processing.
1.2 Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for
wet-chemical processes and dry processing techniques.
1.3 The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent,
on the degree to which a facility adheres to good processing practices as a matter of routine procedure.
1.4 If a nondestructive testing agency as described in Practice E543 is used to perform the examination, the testing agency shall
meet the requirements of Practice E543.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
federal and local codes prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
E94 Guide for Radiographic Examination
E543 Specification for Agencies Performing Nondestructive Testing
E1079 Practice for Calibration of Transmission Densitometers
E1254 Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
E1316 Terminology for Nondestructive Examinations
4
2.2 ANSI Standard: ISO Standards:
ANSI PH 4.8Methylene Blue Method for Measuring Thiosulfate and Silver Densitometric Method for Measuring Residual
Chemicals in Films, Plates, and Papers ISO 11699-2 Nondestructive testing—Industrial Radiographic Film. Part 2: Control
of film processing by means of references values.
ISO 18917 Photography—Determination of residual thiosulfate and other related chemicals in processed photographic
materials—Methods using iodine amylase, methylene blue, and silver sulfide
2.3 CEN Standards:
EN 584-2 Nondestructive Testing—Industrial Radiographic Film. Part 2: Control of film processing by means of reference
4
values
2.4 ANSI Standards:
4
IT 2.26 Photography—Photographic Materials– Determination of Safelight Conditions
3. Terminology
3.1 Definitions—For definitions of terms used in this guide, see Terminology E1316.
1
This guide is under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.01 on Radiology (X and
Gamma) Method.
Current edition approved June 1, 2005.2010. Published June 2005.July 2010. Originally approved in 1990. Last previous edition approved in 19992005 as
E999-99.E999 - 05. DOI: 10.1520/E0999-105.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SE-999 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E999–10
4. Significance and Use
4.1 The provisions in this guide are intended to control the reliability or quality of the image development process only. The
acceptability or quality of industrial radiographic films processed in this manner as well as the materials or products radiographed
remain at the discretion of the user, or inspector, or both. It is further intended that this guide be used as an adjunct to and not a
replacement for Guide E94.
5. Chemical Mixing for Manual and Automatic Processes
5.1 Any equipment that comes in contact with processing solutions should be made of glass, hard rubber, polyethylene, PVC,
enameledsteel,stainlesssteel,oroth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.