EN 485-2:2007

Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3.
Temper designations are defined in Annex B, in compliance with the provisions of EN 515.

Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2: Mechanische Eigenschaften

Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2: Caractéristiques mécaniques

Le présent document spécifie les caractéristiques mécaniques des tôles, bandes et tôles épaisses en aluminium corroyé et alliages d’aluminium corroyés pour applications courantes.
Elle ne s’applique pas aux demi-produits laminés, livrés en bobines, destinés à être relaminés (ébauches pour laminage) ni aux produits spéciaux tels que profils de forme, tôles et bandes ondulées, gravées, laquées, etc., ni aux produits pour applications spéciales telles que la construction aéronautique, le boîtage, les échangeurs thermiques, pour lesquels les caractéristiques mécaniques sont spécifiée dans des normes européennes séparées.
Les limites de composition chimique sont spécifiées dans l’EN 573-3.
Les désignations d’états métallurgiques sont définies dans l’EN 515.

Aluminij in aluminijeve zlitine - Pločevine, trakovi in plošče - 2. del: Mehanske lastnosti

General Information

• Status: Withdrawn
• Publication Date: 03-Apr-2007
• Withdrawal Date: 21-Oct-2008
• ICS: 77.120.10 - Aluminium and aluminium alloys
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 7 - Sheets, strips and plates
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 22-Oct-2008
• Completion Date: 22-Oct-2008
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Ref Project: SIST EN 485-2:2007 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

Relations

• Replaces: EN 485-2:2004 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
• Effective Date: 22-Dec-2008
• Replaced By: EN 485-2:2008 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 485-2:2007
01-junij-2007
1DGRPHãþD
SIST EN 485-2:2004
$OXPLQLMLQDOXPLQLMHYH]OLWLQH3ORþHYLQHWUDNRYLLQSORãþHGHO0HKDQVNH
ODVWQRVWL
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2:
Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2:
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: EN 485-2:2007
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 485-2:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 485-2:2007

---------------------- Page: 2 ----------------------

SIST EN 485-2:2007
EUROPEAN STANDARD
EN 485-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2007
ICS 77.120.10 Supersedes EN 485-2:2004
English Version
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2:
Mechanical properties
Aluminium et alliages d'aluminium - Tôles, bandes et tôles Aluminium und Aluminiumlegierungen - Bänder, Bleche
épaisses - Partie 2: Caractéristiques mécaniques und Platten - Teil 2: Mechanische Eigenschaften
This European Standard was approved by CEN on 28 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 485-2:2007: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 485-2:2007
EN 485-2:2007 (E)
Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Requirements.4
4 List of alloys with mechanical property limits.4
4.1 General.4
4.2 Elongation.5
4.3 List of alloys and their mechanical properties .5
Annex A (normative) Rules for rounding.63
Annex B (informative) Explanation of temper designations used in Tables 1 to 46 based on
definitions of EN 515 .64
Bibliography .66

2

---------------------- Page: 4 ----------------------

SIST EN 485-2:2007
EN 485-2:2007 (E)
Foreword
This document (EN 485-2:2007) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2007, and conflicting n
...