EN 12079-3:2006
(Main)Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testing
Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testing
This part of EN 12079 specifies requirements for the periodic inspection, examination and testing of offshore freight and service containers, built in accordance with EN 12079-1, with maximum gross mass not exceeding 25000 kg and their associated lifting sets, intended for repeated use to, from and between offshore installations and ships. Inspection requirements following damage and repair of offshore containers are also included.
Other parts of the standard are:
EN 12079-1, Offshore containers and associated lifting sets - Part 1: Offshore container – Design, manufacture and marking
EN 12079-2, Offshore containers and associated lifting sets - Part 2: Lifting sets – Design, manufacture and marking
Guidance as to the knowledge and experience required by those responsible for carrying out periodic inspection and testing is given in Annex A 'Recommended knowledge and experience of staff responsible for inspection of offshore containers'
Guidance on pre-trip inspections is given in Annex B ' Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers'
Offshore-Container und zugehörige Anschlaggarnituren - Teil 3: Wiederkehrende Kontrolle, Inspektion und Prüfung
Conteneurs pour manutention en mer et dispositifs de levage associés - Partie 3: Contrôle périodique, inspection et essais
Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 3. del: Periodični nadzor, pregled in preskušanje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testingConteneurs pour manutention en mer et dispositifs de levage associés - Partie 3: Contrôle périodique, inspection et essaisOffshore-Container und zugehörige Anschlaggarnituren - Teil 3: Wiederkehrende Kontrolle, Inspektion und PrüfungTa slovenski standard je istoveten z:EN 12079-3:2006SIST EN 12079-3:2007en55.180.10General purpose containersICS:SIST EN 12079:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 12079-3:200701-januar-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12079-3April 2006ICS 55.180.10Supersedes EN 12079:1999
English VersionOffshore containers and associated lifting sets - Part 3: Periodicinspection, examination and testingConteneurs pour utilisation en mer et dispositifs de levageassociés - Partie 3: Contrôle périodique, inspection etessaisOffshore-Container und zugehörige Anschlaggarnituren -Teil 3: Wiederkehrende Kontrolle, Inspektion und PrüfungThis European Standard was approved by CEN on 9 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12079-3:2006: E
Recommended knowledge and experience of staff responsible for inspection of offshore containers.17 Annex B (informative)
Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers.18
EN 12079-2, Offshore containers and associated lifting sets - Part 2: Lifting sets – Design, manufacture and marking Guidance as to the knowledge and experience required by those responsible for carrying out periodic inspection and testing is given in Annex A 'Recommended knowledge and experience of staff responsible for inspection of offshore containers'. Guidance on pre-trip inspections is given in Annex B ' Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers'.
2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12079-1:2006, Offshore containers and associated lifting sets — Part 1: Offshore containers — Design, manufacture and marking EN 12079-2:2006, Offshore containers and associated lifting sets — Part 2: Lifting sets — Design, manufacture and marking EN 473, Non-destructive testing - Qualification and certification of NDT personnel - General principles EN 571-1, Non-destructive testing - Penetrant testing - General principles EN 818-4:1996, Short link chain for lifting purposes - Safety - Part 4:Chain slings - Grade 8 EN 818-6, Short link chain for lifting purposes - Safety - Part 6:Chain slings - Specification for information for use and maintenance to be provided by the manufacturer EN 970, Non-destructive examination of fusion welds - Visual examination EN 1289, Non-destructive examination of welds - Penetrant testing of welds - Acceptance levels EN 1290, Non-destructive examination of welds - Magnetic particle examination of welds EN 1291, Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels EN 1435, Non-destructive examination of welds - Radiographic examination of welded joints
EN 12517-1, Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels EN 13414-2, Steel wire rope slings - Safety - Part 2:Specification for information for use and maintenance to be provided by the manufacturer EN 30042, Arc-welded joints in aluminium and its weldable alloys - Guidance on quality levels for imperfections (ISO 10042:1992) EN ISO 3834-2, Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) EN ISO 5817, Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2003) EN ISO/IEC 17020, General criteria for the operation of various types of bodies performing inspection (ISO/IEC 17020:1998) 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 12079–1:2006 and the following apply. 3.1 owner legal owner of the offshore container or the delegated nominee of that body 3.2 visual inspection inspection of the characteristics of a product and determination of its conformity with specified requirements where applicable, and based on professional judgement where general requirements apply 3.3 visual examination examination in accordance with EN 970 4 Symbols R The rating i.e. the maximum gross mass of the container including permanent equipment and cargo but excluding the lifting set, in kg; T The tare mass, i.e. the mass of an empty container including any permanent equipment excluding cargo and lifting set, in kg; P The payload, i.e. the maximum permissible mass of cargo which may be safely transported by the container, in kg. NOTE 1 P = R - T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.