iTeh Standards logo
EURUSD
Your shopping cart is empty.
CEN

EN 13044-1:2011/AC:2014

(Corrigendum)

Intermodal Loading Units - Marking - Part 1: Markings for identification

Intermodal Loading Units - Marking - Part 1: Markings for identification

CEN/TC 119 - Editorial modifications to 5.2.3 and A.2 in the English and French versions of EN 13044-1:2011. No xml version as the mother standard EN 13004-1:2012 is not available as an xml file.

Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die Identifizierung

Unités de chargement intermodales - Marquage - Partie 1: Marquages d'identification

Referenčne obremenilne enote - Označevanje - 1. del: Identifikacijske oznake

Ta evropski standard podaja sistem za identifikacijo in predstavitev informacij o referenčnih obremenilnih enotah (ILU). Identifikacijski sistem je namenjen splošni uporabi, na primer pri dokumentiranju, nadzoru in komunikacijah (vključno z avtomatskimi sistemi za obdelavo podatkov), ter prikazu na ILU in drugih zabojnikih, ki niso v skladu s standardi ISO (tj. katerih mere in preskusni parametri se razlikujejo od tistih, opredeljenih v veljavnih standardih ISO), ki se uporabljajo pri evropskem prevozu. Vključene so metode prikaza identifikacijskih in nekaterih drugih podatkov (vključno z obratovalnimi podatki) na ILU s trajnimi oznakami. Ta evropski standard določa: a) identifikacijski sistem ILU s povezanim sistemom za preverjanje natančnosti njegove uporabe, ki ima obvezne oznake za predstavitev identifikacijskega sistema za vidno interpretacijo; b) kodirni sistem za podatke o velikosti in tipu ILU z ustreznimi oznakami za njihov prikaz; c) obvezne obratovalne oznake; d) fizično predstavitev oznak na ILU. Ta del EN 13044 določa sistem za identifikacijo lastnika ILU, kar vključuje povezan sistem za preverjanje natančnosti njegove uporabe. Ta evropski sistem ne zajema začasnih obratovalnih oznak kakršne koli vrste, trajnih oznak, podatkovnih tablic itd., ki jih morda zahtevajo medvladni sporazumi, nacionalna zakonodaja ali nevladne organizacije, ki niso CEN.

General Information

Status
Published
Publication Date
29-Apr-2014
ICS
35.240.60 - IT applications in transport
55.180.10 - General purpose containers
Technical Committee
CEN/TC 119 - Swap bodies for combined goods transport
Drafting Committee
CEN/TC 119/WG 6 - Intermodal Loading Units
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
30-Apr-2014
Completion Date
30-Apr-2014
Directive
2016/797/EU - Directive (EU) 2016/797 of the European Parliament and of the Council of 11 May 2016 on the interoperability of the rail system within the European Union (Text with EEA relevance)
Ref Project
SIST EN 13044-1:2011/AC:2014 - Intermodal Loading Units - Marking - Part 1: Markings for identification

Relations

Corrects
EN 13044-1:2011 - Intermodal Loading Units - Marking - Part 1: Markings for identification
Effective Date
09-Jul-2014
EN 13044-1:2011/AC:2014EN 13044-1:2011/AC:2014
PreviousNext
Corrigendum
EN 13044-1:2011/AC:2014
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die IdentifizierungUnités de chargement intermodales - Marquage - Partie 1: Marquages d'identificationIntermodal Loading Units - Marking - Part 1: Markings for identification55.180.10General purpose containers35.240.60Uporabniške rešitve IT v transportu in trgoviniIT applications in transport and tradeICS:Ta slovenski standard je istoveten z:EN 13044-1:2011/AC:2014SIST EN 13044-1:2011/AC:2014en,fr,de01-julij-2014SIST EN 13044-1:2011/AC:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13044-1:2011/AC
April 2014
Avril 2014
April 2014 ICS 55.180.10; 35.240.60 English version Version Française Deutsche Fassung
Intermodal Loading Units - Marking - Part 1: Markings for identification
Unités de chargement intermodales - Marquage - Partie 1: Marquages d'identification
Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die Identifizierung This corrigendum becomes effective on 30 April 2014 for incorporation in the official English and French versions of the EN.
Ce corrigendum prendra effet le 30 avril 2014 pour incorporation dans les versions officielles anglaise et française de la EN.
Die Berichtigung tritt am
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

Frequently Asked Questions

EN 13044-1:2011/AC:2014 is a corrigendum published by the European Committee for Standardization (CEN). Its full title is "Intermodal Loading Units - Marking - Part 1: Markings for identification". This standard covers: CEN/TC 119 - Editorial modifications to 5.2.3 and A.2 in the English and French versions of EN 13044-1:2011. No xml version as the mother standard EN 13004-1:2012 is not available as an xml file.

CEN/TC 119 - Editorial modifications to 5.2.3 and A.2 in the English and French versions of EN 13044-1:2011. No xml version as the mother standard EN 13004-1:2012 is not available as an xml file.

EN 13044-1:2011/AC:2014 is classified under the following ICS (International Classification for Standards) categories: 35.240.60 - IT applications in transport; 55.180.10 - General purpose containers. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 13044-1:2011/AC:2014 has the following relationships with other standards: It is inter standard links to EN 13044-1:2011. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 13044-1:2011/AC:2014 is associated with the following European legislation: EU Directives/Regulations: 2016/797/EU. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

You can purchase EN 13044-1:2011/AC:2014 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.

The article discusses editorial modifications made to the English and French versions of EN 13044-1:2011/AC:2014, which is a standard for marking intermodal loading units for identification. The modifications specifically address sections 5.2.3 and A.2. It also mentions that there is no XML version of the standard available, as the mother standard EN 13004-1:2012 does not exist in XML format.

記事タイトル：EN 13044-1:2011/AC:2014 - インターモーダル荷役ユニット - マーキング - パート1：識別のためのマーキング 記事内容：CEN/TC 119 - EN 13044-1:2011の英語版およびフランス語版における5.2.3とA.2の編集修正について説明しています。親規格であるEN 13004-1:2012はXMLファイルとして利用できないため、XMLバージョンは存在しません。

기사 제목: EN 13044-1:2011/AC:2014 - 인터모달 로딩 유닛 - 표시 - 파트 1: 식별을 위한 표시 기사 내용: CEN/TC 119 - EN 13044-1:2011의 영어 및 프랑스어 버전에서 5.2.3과 A.2 부분에 대한 편집 수정 사항을 소개합니다. 어머니 표준인 EN 13004-1:2012이 XML 파일로 제공되지 않아 XML 버전이 없습니다.

This May Also Interest You

CEN
EN 13044-2:2011(Main)
Intermodal Loading Units - Marking - Part 2: Markings of swap bodies related to rail operation
SIST EN 13044-2:2011

This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended for general application, for example in documentation, control and communication (including automatic data processing systems), as well as for display on the ILU and other non ISO containers (i.e. which dimensions and testing parameters differ from those defined by the applicable ISO standards) used in European transport.
The methods of displaying identification and specific other data (including operational data) on the ILU by means of permanent marks are included.
This European Standard specifies:
a)   an ILU identification system with an associated system for verifying the accuracy of its use, having mandatory marks for the presentation of the identification system for visual interpretation; and
b)   a coding system for data on ILU size, with corresponding marks for their display;
c)   mandatory operational marks;
d)   physical presentation of the marks on the ILU.
This part of the European Standard prescribes the system of operational data for the codification of the swap bodies. The codification assigns a maximum profile for the cover area available at the rail tracks to the swap bodies in order to enable the selection of those rail tracks on which these swap bodies can be transported without any danger.
This part of the European Standard prescribes furthermore the additional operational markings, which are necessary for railway operation.
This European Standard does not cover temporary operational marks of any kind, permanent marks, data plates, etc. which may be required by intergovernmental agreements, national legislation or non-governmental organisations other than CEN.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13044-3:2011(Main)
Intermodal Loading Units - Marking - Part 3: Markings of semi-trailers related to rail operation
SIST EN 13044-3:2011

This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended for general application, for example in documentation, control and communication (including automatic data processing systems), as well as for display on the ILU and other non ISO containers (i.e. which dimensions and testing parameters differ from those defined by the applicable ISO standards) used in European transport.
The methods of displaying identification and specific other data (including operational data) on the ILU by means of permanent marks are included.
This European Standard specifies:
a)   an ILU identification system with an associated system for verifying the accuracy of its use, having mandatory marks for the presentation of the identification system for visual interpretation, and
b)   a coding system for data on ILU size, with corresponding marks for their display;
c)   mandatory operational marks;
d)   physical presentation of the marks on the ILU.
This part of the European Standard prescribes the system of operational data for the codification of the semi-trailer. The codification assigns a maximum profile for the cover area available at the rail tracks to the semi-trailer in order to enable the selection of those rail tracks on which these semi-trailers can be transported without any danger.
This part of the European Standard prescribes furthermore the additional operational markings, which are necessary for railway operation.
This European Standard does not cover temporary operational marks of any kind, permanent marks, data plates, etc. which may be required by intergovernmental agreements, national legislation or non-governmental organisations other than CEN.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13044-1:2011(Main)
Intermodal Loading Units - Marking - Part 1: Markings for identification
SIST EN 13044-1:2011

This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended for general application, for example in documentation, control and communications (including automatic data processing systems), as well as for display on an ILU and other non ISO containers (i.e. which dimensions and testing parameters differ from those defined by the applicable ISO standards) used in European transport.
The methods of displaying identification and certain other data (including operational data) on ILUs by means of permanent marks are included.
This European Standard specifies:
a)   an ILU identification system with an associated system for verifying the accuracy of its use, having mandatory marks for the presentation of the identification system for visual interpretation, and
b)   a coding system for data on ILU size and type, with corresponding marks for their display;
c)   mandatory operational marks;
d)   physical presentation of the marks on the ILU.
This part of EN 13044 specifies a system to identify the owner of the ILU, which includes an associated system for verifying the accuracy of its use.
This European Standard does not cover temporary operational marks of any kind, permanent marks, data plates, etc. which may be required by intergovernmental agreements, national legislation or non-governmental organisations other than CEN.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12285-4:2025(Main)
Workshop fabricated steel tanks - Part 4: Vertical cylindrical single skin and double skin tanks for the aboveground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of buildings
kSIST FprEN 12285-4:2023

This document specifies the requirements for metallic shop fabricated cylindrical vertical steel tanks, single and double skin for the aboveground storage of water polluting liquids (both flammable and non-flammable) within the following limits:
—   from Ø 1250 mm up to Ø 4 000 mm inner tank nominal diameter, and
—   up to maximum overall shell length of 6 times the nominal inner tank diameter (or max 14 m shell lenght Lz), and
—   tank possible to be divided from 1 to 5 compartments,
—   for liquids with maximum density of up to 1,9 kg/l, and
—   with an operating pressure (P0) of maximum 50kPa (0,5 bar (g)) and minimum – 5 kPa (- 50 mbar (g)), and
—   where double skin tanks with vacuum leak detection system are used the kinematic viscosity of the stored media shall not exceed 5 × 10−3 m2/s.
This document is applicable for normal ambient temperature conditions (−40 °C to + 50 °C). Where temperatures are outside this range, additional requirements need to be taken into account.
This document is not applicable to tanks used for storage and/or supply of fuel/gas for building heating/cooling systems, and of hot or cold water not intended for human consumption, nor to loads and special measures necessary in areas subject to risk of earthquakes.
This document is not applicable for the storage of liquids having dangerous goods classes listed in Table 1 because of the special dangers involved.
Table 1 - List of dangerous goods which are not covered by this document
UN-classification   Type of dangerous goods
Class 1   Explosives
Class 4.2   Substances liable to spontaneous combustion
Class 4.3   Substances which in contact with water emit flammable gases
Class 5.2   Organic peroxides
Class 6.2   Infectious substances
Class 7   Radioactive substances, hydrocyanic or hydrocyanic solvent liquids, metal carbons, hydrofluoric acid, bromide liquids
NOTE   The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 6.2).

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14245:2021/A1:2025(Amendment)
Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing - Amendment 1 (ISO 14245:2021/Amd 1:2025)
SIST EN ISO 14245:2021/oprA1:2025
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11929-3:2025(Main)
Determination of the characteristic limits (decision threshold, detection limit and limits of the coverage interval) for measurements of ionizing radiation - Fundamentals and application - Part 3: Applications to unfolding methods (ISO 11929-3:2025)
oSIST prEN ISO 11929-3:2025

The ISO 11929 series specifies a procedure, in the field of ionizing radiation metrology, for the calculation of the “decision threshold”, the “detection limit” and the “limits of the coverage interval” for a non-negative ionizing radiation measurand when counting measurements with preselection of time or counts are carried out. The measurand results from a gross count rate and a background count rate as well as from further quantities on the basis of a model of the evaluation. In particular, the measurand can be the net count rate as the difference of the gross count rate and the background count rate, or the net activity of a sample. It can also be influenced by calibration of the measuring system, by sample treatment and by other factors.
ISO 11929 has been divided into four parts covering elementary applications in ISO 11929-1, advanced applications on the basis of the ISO/IEC Guide 98-3:2008/Suppl 1:2008 in ISO 11929-2, applications to unfolding methods in this document, and guidance to the application in ISO 11929-4.
ISO 11929-1 covers basic applications of counting measurements frequently used in the field of ionizing radiation metrology. It is restricted to applications for which the uncertainties can be evaluated on the basis of the ISO/IEC Guide 98-3 (JCGM 2008). In ISO 11929-1:2025, Annex A, the special case of repeated counting measurements with random influences is covered, while measurements with linear analogous ratemeters, are covered in ISO 11929-1:2025, Annex B.
This document deals with the evaluation of measurements using unfolding methods and counting spectrometric multi-channel measurements if evaluated by unfolding methods, in particular, for alpha- and gamma‑spectrometric measurements. Further, it provides some advice on how to deal with correlations and covariances.
ISO 11929-4 gives guidance to the application of the ISO 11929 series, summarizes shortly the general procedure and then presents a wide range of numerical examples.
ISO 11929 Standard also applies analogously to other measurements of any kind especially if a similar model of the evaluation is involved. Further practical examples can be found, for example, in ISO 18589[7], ISO 9696[2], ISO 9697[3], ISO 9698[4], ISO 10703[5], ISO 7503[1], ISO 28218[8], and ISO 11665[6].
NOTE            A code system, named UncertRadio, is available for calculations according to ISO 11929- 1 to ISO 11929-3. UncertRadio[35][36] can be downloaded for free from https://www.thuenen.de/en/institutes/fisheries-ecology/fields-of-activity/marine-environment/coordination-centre-of-radioactivity/uncertradio.The download contains a setup installation file which copies all files and folders into a folder specified by the user. After installation one has to add information to the PATH of Windows as indicated by a pop‑up window during installation. English language can be chosen and extensive “help” information is available.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 415-4:2025(Main)
Safety of packaging machines - Part 4: Palletizers and depalletizers and associated equipment
kSIST FprEN 415-4:2024

This document is applicable to the following groups of machines, auxiliary equipment and their combinations:
-   palletizers;
-   depalletizers;
-   auxiliary equipment incorporated in or linked to the operations of palletizers and depalletizers;
-   conveying systems which are part of palletizers or depalletizers;
-   palletizers combined with functions of machines which are covered by other parts of EN 415, but detailed requirements are only provided for palletizing functions.
The individual machines are described in 3.2. Auxiliary equipment is described in 3.3.
This document deals with safety requirements for machine design, transport, installation, commissioning, operation, adjustment, maintenance and cleaning of palletizers, depalletizers, auxiliary equipment and conveying systems which are part of palletizer or depalletizer. The extent to which hazards, hazardous situations and events are covered is indicated in Annex A.
Exclusions:
This document is not applicable to the following machines:
-   machines that were manufactured before the date of publication of this document by CEN;
-   conveyors that connect palletizers and depalletizers with machines that are not in the scope of this document.
Conveyors in the scope of this document also fall in the scope of EN 619:2022, however, this document describes the additional or specific hazards for conveyors fitted into palletizers and depalletizers and so the requirements of this document take precedence over the requirements of EN 619:2022.
This document does not consider the following hazards:
—   the use of palletizers and depalletizers in a potentially explosive atmosphere;
—   the health, safety or hygiene hazards associated with the products that are contained in the unit load handled by palletizers and depalletizers except for the spillage of hazardous substances caused by the malfunction of a machine.

  • Draft
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14078:2025(Main)
Liquid petroleum products - Determination of fatty acid methyl ester (FAME) content in middle distillates - Infrared spectrometry method
SIST EN 14078:2026

This document specifies a test method for the determination of fatty acid methyl ester (FAME) content in diesel fuel or domestic heating fuel by mid-infrared (IR) spectrometry and a transmission sample cell, which applies to FAME contents of the three measurement ranges as follows:
-   range A: for FAME contents ranging from approx. 0,05 % (V/V) to approx. 3 % (V/V);
-   range B: for FAME contents ranging from approx. 3 % (V/V) to approx. 20 % (V/V);
-   range C: for FAME contents ranging from approx. 20 % (V/V) to approx. 50 % (V/V).
Principally, higher FAME contents can also be analysed if diluted; however, no precision data for results outside the specified range is available at present.
This test method was verified to be applicable to samples which contain FAME conforming to EN 14214. Reliable quantitative results are obtained only if the samples do not contain any significant amounts of other interfering components, especially esters and other carbonyl compounds which possess absorption bands in the spectral region used for quantification of FAME. If such interfering components are present, this test method is expected to produce higher values.
NOTE 1   For the purposes of this document, the term “% (V/V)” is used to represent the volume fraction (φ) of a material.
NOTE 2   For conversion of grams FAME per litre (g FAME/l) to volume fraction, a fixed density for FAME of 883,0 kg/m3 is adopted.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-15:2025(Main)
Woodworking machines - Safety - Part 15: Presses (ISO 19085-15:2025)
kSIST FprEN ISO 19085-15:2025

1.1    This document specifies the safety requirements and measures for
—    cold presses,
—    hot presses,
—    bending presses,
—    edge/face gluing presses,
—    membrane presses, and
—    embossing presses,
where the pressing force is applied by hydraulic, pneumatic or electrical actuators pushing two flat or shaped surfaces against each other, capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
1.2    This document is applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with:
a)    a device for hot gluing;
b)    a device for high-frequency gluing in the frequency range from 1 MHz to 400 MHz;
c)    a device for high-frequency shaping in the frequency range from 1 MHz to 400 MHz;
d)    an automatic workpiece loading and unloading system;
e)    an intermediate additional platen;
f)    a workpiece extractor;
g)    a horizontal pressing system;
h)    split moveable platens.
1.3    The machines are designed to process workpieces consisting of:
a)    solid wood;
b)    materials with similar characteristics to wood (see ISO 19085-1:2021, 3.2), except those with light alloy laminates/edges/profiles for high-frequency presses;
c)    wood-based material such as chipboard, fibreboard and plywood composed/laminated with steel sheets/edges/profiles, except for high-frequency presses;
d)    honeycomb board;
e)    composite boards made from the materials listed above.
1.4    This document does not deal with any hazards related to:
—    specific devices that differ from the list above;
—    hot fluid heating systems internal to the machine other than electrical;
—    any hot fluid heating systems external to the machine;
—    operation of taking intermediate platens out and in again;
—    the combination of a single machine being used with any other machine (as part of a line).
1.5    This document is not applicable to:
—    frame presses;
—    membrane presses where the pressing force is applied by vacuum only;
—    presses for producing chipboard, fibreboard, OSB;
—    machines intended for use in potentially explosive atmosphere;
—    machines manufactured before the date of publication of this document.

  • Draft
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15827:2025(Main)
Railway applications - System Engineering requirements for bogies and running gear
SIST EN 15827:2026

This document is applicable to the system engineering of bogies and running gear for rail vehicles, including those vehicles intended to operate under the Interoperability Directives.
It specifies the requirements to achieve:
-   a satisfactory design of bogie or running gear,
-   validation of the design within its operating envelope, and
-   a maintenance plan
to ensure that the relevant performance and safety criteria are maintained.
The scope of the system engineering process specified in this document includes the design, validation and maintenance of bogies and running gear. No requirements are specified for other systems components that are attached to the bogies or running gear, except to ensure that a satisfactory interface has been provided.
NOTE   Specifications that relate to bogies and running gear can only be considered in the context of a specific vehicle application. Therefore, the performance, including safety, can relate only to the bogies and running gear as part of a vehicle configuration and not to the individual elements of the bogies or running gear.

  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day