EN ISO 15614-10:2005

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 10: Hyperbaric dry welding (ISO 15614-10:2005)

ISO 15614-10:2005 specifies how to qualify welding procedure specifications for welding in hyperbaric dry environments.
It also specifies the minimum testing requirements necessary for qualification of welding procedures.
ISO 15614-10:2005 may be used to qualify welding procedures using mechanized and automated welding.

Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißverfahrensprüfung - Teil 10: Trockenschweißen unter Überdruck (ISO 15614-10:2005)

Dieser Teil von ISO 15614 legt fest, wie Schweißanweisungen durch Schweißverfahrensprüfungen für das Schweißen in trockener Überdruckumgebung zu qualifizieren sind.
Er legt ebenfalls die Mindestprüfanforderungen fest, die für die Qualifizierung von Schweißverfahren notwendig sind.
Dieser Teil von ISO 15614 darf zur Qualifizierung von Schweißverfahren beim mechanischen und automatischen Schweißen verwendet werden.
ANMERKUNG   Dieser Teil von ISO 15614 ist Teil einer Normenreihe. Einzelheiten dieser Normenreihe sind in ISO 15607:2003, Anhang A, angegeben.

Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Epreuve de qualification d'un mode opératoire de soudage - Partie 10: Soudage hyperbar en caisson (ISO 15614-10:2005)

L'ISO 15614-10:2005 spécifie comment qualifier des descriptifs de modes opératoires de soudage pour le soudage dans un environnement hyperbare en caisson.
Elle spécifie également les exigences minimales nécessaires à l'épreuve de qualification de mode opératoire de soudage.
L'ISO 15614-10:2005 peut être utilisée pour qualifier des modes opératoires de soudage en utilisant le soudage mécanisé et le soudage automatique.

Popis in kvakifikacija varilnih postopkov za kovinske materiale - Preskus varilnega postopka - 10. del: Hiperbarično suho podvodno varjenje (ISO 15614-10:2005)

General Information

• Status: Published
• Publication Date: 14-Feb-2005
• Withdrawal Date: 30-Aug-2005
• ICS: 25.160.10 - Welding processes
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/SC 4 - Quality management in the field of welding
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 08-May-2009
• Completion Date: 08-May-2009
• Ref Project: SIST EN ISO 15614-10:2005 - Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 10: Hyperbaric dry welding (ISO 15614-10:2005)

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2005
3RSLVLQNYDNLILNDFLMDYDULOQLKSRVWRSNRY]DNRYLQVNHPDWHULDOH3UHVNXVYDULOQHJD
SRVWRSNDGHO+LSHUEDULþQRVXKRSRGYRGQRYDUMHQMH,62
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 10: Hyperbaric dry welding (ISO 15614-10:2005)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 10: Trockenschweißen unter Überdruck (ISO 15614-
10:2005)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Epreuve de qualification d'un mode opératoire de soudage - Partie 10:
Soudage hyperbar en caisson (ISO 15614-10:2005)
Ta slovenski standard je istoveten z: EN ISO 15614-10:2005
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15614-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS 25.160.10
English version
Specification and qualification of welding procedures for metallic
materials - Welding procedure test - Part 10: Hyperbaric dry
welding (ISO 15614-10:2005)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Epreuve de qualification metallische Werkstoffe - Schweißverfahrensprüfung - Teil
d'un mode opératoire de soudage - Partie 10: Soudage 10: Trockenschweißen unter Überdruck (ISO 15614-
hyperbar en caisson (ISO 15614-10:2005) 10:2005)
This European Standard was approved by CEN on 3 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15614-10:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 15614-10:2005) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2005, and conflicting national
standards shall be withdrawn at the latest by August 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 15614-10:2005 has been approved by CEN as EN ISO 15614-10:2005 without
any modifications.
INTERNATIONAL ISO
STANDARD 15614-10
First edition
2005-02-15
Specification and qualification of welding
procedures for metallic materials —
Welding procedure test —
Part 10:
Hyperbaric dry welding
Descriptif et qualification d'un mode opératoire de soudage pour les
matériaux métalliques — Épreuve de qualification d'un mode
opératoire de soudage —
Partie 10: Soudage hyperbare en caisson

Reference number
ISO 15614-10:2005(E)
©
ISO 2005
ISO 15614-10:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 15614-10:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Preliminary welding procedure specification (pWPS) . 2
5 Welding procedure test . 3
6 Test piece. 3
6.1 General. 3
6.2 Shape and dimensions of test pieces. 3
6.3 Welding of test pieces . 3
7 Examination and testing. 4
7.1 Extent of testing . 4
7.2 Location and cutting of test specimens . 4
7.3 Non-destructive testing. 4
7.4 Destructive tests . 4
7.5 Re-testing. 4
8 Range of qualification. 4
8.1 General. 4
8.2 Related to the manufacturer . 5
8.3 Related to the parent material. 5
8.4 Common to all welding procedures . 5
8.5 Specific to processes . 7
8.6 Specific to hyperbaric environment. 7
9 Welding procedure qualification record (WPQR) . 8

ISO 15614-10:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15614-10 was prepared by Technical Committee ISO/TC 44, Welding and allied processes.
ISO 15614 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure test:
 Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
 Part 2: Arc welding of aluminium and its alloys
 Part 3: Arc welding of cast iron
 Part 4: Finishing welding of aluminium castings
 Part 5: Arc welding of titanium, zirconium and their alloys
 Part 6: Arc welding of copper and its alloys
 Part 7: Overlay welding
 Part 8: Welding of tubes to tube-plate joints
 Part 9: Arc underwater hyperbaric wet welding
 Part 10: Hyperbaric dry welding:
 Part 11: Electron and laser beam welding
 Part 12: Spot, seam and projection welding
 Part 13: Resistance butt and flash welding
iv © ISO 2005 – All rights reserved

ISO 15614-10:2005(E)
Introduction
All new welding procedure qualifications are to be carried out in accordance with this part of ISO 15614 from
the date of publication.
This part of ISO 15614 does not invalidate previously qualified welding procedures in accordance with other
standards or specifications, providing the technical requirements are satisfied and the previous qualifications
are relevant to the application and production work on which they are to be employed.
Where additional tests have to be carried out to make the qualification technically equivalent, it is only
necessary to do the additional tests in accordance with this part of ISO 15614.
Requested for official interpretations of any aspect of this standard should be directed to the Secretariat of
ISO/TC 44 via your national standards body, a complete listing of which can be found at www.iso.org.

INTERNATIONAL STANDARD ISO 15614-10:2005(E)

Specification and qualification of welding procedures for
metallic materials — Welding procedure test —
Part 10:
Hyperbaric dry welding
1 Scope
This part of ISO 15614 specifies how to qualify welding procedure specifications for welding in hyperbaric dry
environments.
It also specifies the minimum testing requirements necessary for qualification of welding procedures.
This part of ISO 15614 may be used to qualify welding procedures using mechanized and automated welding.
NOTE This part of ISO 15614 is part of a series of standards, details of this series are given in ISO 15607:2003,
Annex A.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
ISO 6947, Welds — Working positions — Definitions of angles of slope and rotation
ISO 14175, Welding consumables — Shielding gases for arc welding and cutting
ISO 15607:2003, Specification and qualification of welding procedures for metallic materials — General rules
ISO 15609-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 1: Arc welding
ISO 15618-2, Qualificat
...