iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12200-1:2000

(Main)

Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

This standard specifies the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater downpipes. It also specifies the test parameters for the test methods referred to in this standard. These products are usually used in conjunction with gutters conforming to EN 607.

Kunststoff-Rohrleitungssysteme für außenliegende Regenfalleitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Diese Norm legt Anforderungen an Rohre, Formstücke und das Rohrleitungssystem aus weichmacherfreiem Polyvinylchlorid (PVC-U) fest, die in außenliegenden Regenfalleitungen eingesetzt werden. Rohrleitungsteile nach dieser Norm werden üblicherweise mit Dachrinnen aus PVC-U nach EN 607 verwendet.

Systèmes de canalisations de descentes d'eaux pluviales en plastique à usage externe en aérien - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 1: Spécifications pour tubes, raccords et le système

Cette norme spécifie les exigences pour les tubes, les raccords et le système fabriqués à partir de poly(chlorure de vinyle) non plastifié destinés à être utilisés pour les descentes d'eaux pluviales aériennes à l'extérieur des bâtiments. Elle spécifie également les paramètres d'essais pour les méthodes d'essais référencées dans cette norme. Ces produits sont habituellement utilisés conjointement avec les gouttières conformes à la norme EN 607.

Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

General Information

Status
Withdrawn
Publication Date
19-Sep-2000
Withdrawal Date
05-Apr-2016
ICS
23.040.01 - Pipeline components and pipelines in general
23.040.05 - Pipeline and its parts for external sewage systems
23.040.20 - Plastics pipes
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 15 - Pipes and fittings for piping systems for rainwater discharge
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
06-Apr-2016
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 12200-1:2001 - Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

Relations

Replaced By
EN 12200-1:2016 - Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
Effective Date
08-Jun-2022

Buy Standard

EN 12200-1:2001EN 12200-1:2001
PreviousNext
Standard
EN 12200-1:2001
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system5RKUOHLWXQJVV\VWHPWXEHVPlastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system93.025Zunanji sistemi za prevajanje vodeExternal water conveyance systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN 12200-1:2000SIST EN 12200-1:2001en01-april-2001SIST EN 12200-1:20
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 1046:2021(Main)
Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
SIST-TS CEN/TS 1046:2021

This document gives the recommended practise for underground open trench installation and commissioning of thermoplastics piping systems to be used for the conveyance of water under pressure (in addition to EN 805) and for the discharge of wastewater under gravity (in addition to EN 1610) .
In the field of non-pressure underground drainage and sewerage this is reflected in the marking of products by application code "U" and "UD":
-   outside the building structure (U);
-   both buried in ground within the building structure (application area code "D") and outside the
building (application area code "UD").
This document covers also installation and/or connections to valves, manholes, inspection chambers, gullies and other ancillary components in piping systems.
NOTE 1   Code of practise for pipelines for gas supply is covered by EN 12007-series [21].
NOTE 2   Recommended practices for installation of plastic piping systems for soil and waste discharge within the building structure is covered by CEN/TR 13801 [12].
NOTE 3   Practices for underground installation of rainwater infiltration and storage attenuation systems are covered by CEN/TR 17179 [13].
NOTE 4   It is assumed that additional recommendations and/or requirements are detailed in the individual product standards.
NOTE 5    If non-plastic components are part of the plastic system the manufacturer's instructions should be taken into account.
Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations. This document gives specific additional recommendations for commissioning relevant for plastic piping systems.
Attention is drawn to any relevant local and/or national regulations (e.g. health, safety and hygienic requirements).

  • Technical specification
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12200-1:2016(Main)
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 12200-1:2016

This European Standard specifies the requirements for pipes, fittings, brackets and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater piping systems.
It also specifies:
a)   The requirements for metallic brackets.
b)   Both solid wall pipes and fittings, (i.e. product manufactured from a single layer), as well as solid wall multi-layer pipes.
c)   The test parameters for the test methods referred to in this standard.
Pipes can be used in conjunction with fittings and brackets of acrylic materials provided these polymers meet the performance requirements of this standard.
The products are usually used in conjunction with gutters conforming to EN 607 [1]. They are not intended for use with products conforming to EN 612 [2].
This standard is applicable to PVC-U rainwater systems of circular, square, rectangular or any other shape with sealed (rubber ring or solvent cement) or unsealed joints.
This standard covers a range of pipes and fittings sizes.
NOTE 1    It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range to take into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 2   The term "rainwater" in this standard is used also to encompass "surface water" (as defined in EN 752 [6]) run-off from buildings.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13476-3(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B
oSIST prEN 13476-3:2024

This document, together with prEN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended for use in non-pressure underground drains and sewers for foul wastewater.
NOTE 1   Products complying with this document can also be used in non-pressure underground drains and sewers for surface water.
This document is applicable to pipes and fittings with smooth internal and profiled external surfaces, designated as Type B.
This document also specifies test methods and test parameters.
This document is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure, reflected in the marking of products by “U”; and
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure, reflected in the marking of products by “UD”.
This document is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This document covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application areas, tolerance classes and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1046:2021(Main)
Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
SIST-TS CEN/TS 1046:2021

This document gives the recommended practise for underground open trench installation and commissioning of thermoplastics piping systems to be used for the conveyance of water under pressure (in addition to EN 805) and for the discharge of wastewater under gravity (in addition to EN 1610) .
In the field of non-pressure underground drainage and sewerage this is reflected in the marking of products by application code "U" and "UD":
-   outside the building structure (U);
-   both buried in ground within the building structure (application area code "D") and outside the
building (application area code "UD").
This document covers also installation and/or connections to valves, manholes, inspection chambers, gullies and other ancillary components in piping systems.
NOTE 1   Code of practise for pipelines for gas supply is covered by EN 12007-series [21].
NOTE 2   Recommended practices for installation of plastic piping systems for soil and waste discharge within the building structure is covered by CEN/TR 13801 [12].
NOTE 3   Practices for underground installation of rainwater infiltration and storage attenuation systems are covered by CEN/TR 17179 [13].
NOTE 4   It is assumed that additional recommendations and/or requirements are detailed in the individual product standards.
NOTE 5    If non-plastic components are part of the plastic system the manufacturer's instructions should be taken into account.
Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations. This document gives specific additional recommendations for commissioning relevant for plastic piping systems.
Attention is drawn to any relevant local and/or national regulations (e.g. health, safety and hygienic requirements).

  • Technical specification
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12200-1:2016(Main)
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 12200-1:2016

This European Standard specifies the requirements for pipes, fittings, brackets and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater piping systems.
It also specifies:
a)   The requirements for metallic brackets.
b)   Both solid wall pipes and fittings, (i.e. product manufactured from a single layer), as well as solid wall multi-layer pipes.
c)   The test parameters for the test methods referred to in this standard.
Pipes can be used in conjunction with fittings and brackets of acrylic materials provided these polymers meet the performance requirements of this standard.
The products are usually used in conjunction with gutters conforming to EN 607 [1]. They are not intended for use with products conforming to EN 612 [2].
This standard is applicable to PVC-U rainwater systems of circular, square, rectangular or any other shape with sealed (rubber ring or solvent cement) or unsealed joints.
This standard covers a range of pipes and fittings sizes.
NOTE 1    It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range to take into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 2   The term "rainwater" in this standard is used also to encompass "surface water" (as defined in EN 752 [6]) run-off from buildings.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13476-3(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B
oSIST prEN 13476-3:2024

This document, together with prEN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended for use in non-pressure underground drains and sewers for foul wastewater.
NOTE 1   Products complying with this document can also be used in non-pressure underground drains and sewers for surface water.
This document is applicable to pipes and fittings with smooth internal and profiled external surfaces, designated as Type B.
This document also specifies test methods and test parameters.
This document is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure, reflected in the marking of products by “U”; and
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure, reflected in the marking of products by “UD”.
This document is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This document covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application areas, tolerance classes and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3379:2024(Main)
Leather - Determination of distension and strength of surface (Ball burst method) (ISO 3379:2024)
SIST EN ISO 3379:2025

This document specifies a test method for the determination of distension and strength of the leather grain or finished surface. This method is applicable to all flexible leathers and it is particularly suitable to determine the lastability of leathers for footwear uppers.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12007-5:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements
SIST EN 12007-5:2025

This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007 1 for:
a)   a maximum operating pressure (MOP) up to and including 16 bar;
b)   an operating temperature between −20 °C and +40 °C;
c)   gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line.
It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator’s nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve).
This document does not apply retrospectively to installations before the publication date unless specifically stated.
Specific functional requirements for:
—   polyethylene pipelines are given in EN 12007 2;
—   steel pipelines are given in EN 12007 3;
—   polyamide (PA-U) pipelines are given in CEN/TS 12007 6;
—   pipework for buildings are given in EN 1775;
—   pressure regulating installations are given in EN 12279 or EN 12186;
—   pressure testing, commissioning and decommissioning are given in EN 12327;
—   safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 gives:
—   description of legislations/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 18003:2024(Main)
Food authenticity - Determination of 16-O-Methylcafestol content of green and roasted coffee - HPLC-method
SIST EN 18003:2025

This document specifies a high-performance liquid chromatography (HPLC) method for determining the 16-O-Methylcafestol content in green and roasted coffee.
The method is suitable for a content of 40 mg/kg to 1 600 mg/kg of 16-O-Methylcafestol of green and roasted coffee, respectively. The collaborative study has shown that mass fractions also between 20 mg/kg to 40 mg/kg can be successfully analysed depending on the laboratory equipment.
The compliance assessment process is not part of this document.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17972:2024(Main)
Food authenticity - Food authenticity and fraud - Concepts, terms and definitions
SIST EN 17972:2025

This document provides technical definitions of terms relating to authenticity and fraud when referring to food products. All terms and definitions are in the context of food supply chains, but most of them can also be applied when referring to feed products and the feed supply chain.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day