EN ISO 13229:2011

Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)

ISO 13229:2010 specifies a method for the determination of the viscosity number (also known as reduced viscosity) and K-value of an unplasticized poly(vinyl chloride) (PVC) resin derived from a pipe, fitting or compound.
In ISO 13229:2010, only the method for isolation (or separation) of the PVC resin is detailed.

Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung der Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010)

Diese Internationale Norm legt ein Verfahren zur Bestimmung der Viskositätszahl (auch als reduzierte Viskosi-tät bezeichnet) und des K-Wertes eines weichmacherfreien Polyvinylchlorid-(PVC-)Harzes aus einem Rohr, Formstück oder Formmasse fest. In dieser Internationalen Norm wird nur das Verfahren zur Abspaltung (oder Separation) des PVC-Harzes beschrieben, während die Bestimmung der Viskositätszahl in ISO 1628-2 angegeben ist. Das Vorhandensein anderer Zusätze oder Polymere kann die Anwendung dieses Verfahrens ausschließen (siehe Abschnitt 3).

Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de viscosité réduite et de la valeur K (ISO 13229:2010)

L'ISO 13229:2010 spécifie une méthode de détermination de l'indice de viscosité (également appelé «viscosité réduite») et de la valeur K d'une résine de poly(chlorure  de vinyle) (PVC) non plastifié prélevée sur un tube, un raccord ou une composition.
Dans l'ISO 13229:2010, seule la méthode de séparation de la résine PVC est détaillée.

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu - Cevi in fitingi iz nemehčanega polivinilklorida (PVC-U) - Ugotavljanje viskoznostnega števila in izračunavanje K-vrednosti (ISO 13229:2010)

Ta mednarodni standard določa metodo za ugotavljanje viskoznostnega števila (znanega tudi kot reducirane viskoznosti) in izračunavanje K-vrednosti nemehčane polivinilkloridne (PVC) smole, pridobljene iz cevi, fitinga ali zmesi.
V tem mednarodnem standardu je podrobno opisana le metoda za izolacijo (oziroma ločevanje) PVC-smole, ugotavljanje viskoznostnega števila pa je podano v ISO 1628-2.
Prisotnost drugih aditivov ali polimerov lahko to metodo razveljavi (glej točko 3).

General Information

• Status: Published
• Publication Date: 06-Sep-2011
• Withdrawal Date: 30-Mar-2012
• ICS: 23.040.20 - Plastics pipes
• ICS: 91.140.80 - Drainage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 07-Sep-2011
• Due Date: 26-May-2012
• Completion Date: 07-Sep-2011
• Ref Project: SIST EN ISO 13229:2011 - Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)

Relations

• Replaces: EN 922:1994 - Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value
• Effective Date: 10-Sep-2011

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13229:2011
01-december-2011
1DGRPHãþD
SIST EN 922:1997
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORYNLGHOXMHMRSRWHåQRVWQHPSULQFLSX&HYLLQ
ILWLQJLL]QHPHKþDQHJDSROLYLQLONORULGD39&88JRWDYOMDQMHYLVNR]QRVWQHJD
ãWHYLODLQL]UDþXQDYDQMH.YUHGQRVWL,62
Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value
(ISO 13229:2010)
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Rohre und
Formstücke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung der
Viskositätszahl und Berechnung des K-Wertes (ISO 13229:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Tubes et
raccords en poly(chlorure de vinyle) non plastifié (PVC-U) - Détermination de l'indice de
viscosité réduite et de la valeur K (ISO 13229:2010)
Ta slovenski standard je istoveten z: EN ISO 13229:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN ISO 13229:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13229:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 13229:2011


EUROPEAN STANDARD
EN ISO 13229

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2011
ICS 23.040.20; 91.140.80 Supersedes EN 922:1994
English Version
Thermoplastics piping systems for non-pressure applications -
Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings -
Determination of the viscosity number and K-value (ISO
13229:2010)
Systèmes de canalisations thermoplastiques pour Rohrleitungssysteme aus Thermoplasten für drucklose
applications sans pression - Tubes et raccords en Anwendungen - Rohre und Formstücke aus
poly(chlorure de vinyle) non plastifié (PVC-U) - weichmacherfreiem Polyvinylchlorid (PVC-U) - Bestimmung
Détermination de l'indice de viscosité réduite et de la valeur der Viskositätszahl und Berechnung des K-Wertes (ISO
K (ISO 13229:2010) 13229:2010)
This European Standard was approved by CEN on 11 August 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13229:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13229:2011
EN ISO 13229:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 13229:2011
EN ISO 13229:2011 (E)
Foreword
The text of ISO 13229:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 13229:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting
systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at
the latest by March 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 922:1994.
According to the CEN/CENELEC Internal Regulations, the national
...