EN 12413:2007+A1:2011
(Main)Safety requirements for bonded abrasive products
Safety requirements for bonded abrasive products
This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products.
This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4 of this standard.
This standard does not apply to superabrasives and coated abrasive products.
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Diese Norm gilt für rotierende Schleifkörper aus gebundenem Schleifmittel. Sie legt Anforderungen und/oder Maßnahmen zur Beseitigung oder Verringerung von Gefährdungen fest, die von der Gestaltung und Anwendung der Schleifwerkzeuge herrühren.
Diese Norm umfasst auch Verfahren und Prüfungen zur Feststellung der Übereinstimmung mit den Anforderungen sowie Benutzerinformationen, die der Hersteller dem Anwender zur Verfügung zu stellen hat.
Die berücksichtigten Gefährdungen sind in Abschnitt 4 dieser Norm aufgeführt.
Diese Norm gilt nicht für Schleifkörper mit Diamant oder Bornitrid als Schleifmittel und nicht für Schleifmittel auf Unterlagen.
Exigences de sécurité pour les produits abrasifs agglomérés
La présente norme s'applique aux produits abrasifs agglomérés rotatifs. Elle spécifie les exigences et/ou mesures pour la suppression ou la réduction des risques résultant de la conception et de l'application des produits abrasifs.
La présente norme contient également les modes opératoires et les essais permettant de vérifier la conformité avec les exigences ainsi que les informations de sécurité pour l'utilisation que le fabricant doit fournir à l’utilisateur.
Les phénomènes dangereux à prendre en considération sont listés à l'Article 4 de la présente norme.
La présente norme ne s'applique pas aux superabrasifs, ni aux produits abrasifs appliqués.
Varnostne zahteve za vezana brusilna sredstva
Ta standard velja za rotirajoča se vezana brusilna sredstva. Določa zahteve in/ali ukrepe za odpravo ali zmanjševanje nevarnosti, ki so posledica načrtovanja in uporabe abrazivnih proizvodov.
Ta standard vsebuje tudi postopke in preskuse za preverjanje skladnosti z zahtevami in varnostnimi informacijami o uporabi, ki jih mora proizvajalec priskrbeti uporabniku.
Nevarnosti, ki so upoštevane, so navedene v klavzuli 4 tega standarda.
Ta standard ne velja za superabrazive in prevlečene abrazivne proizvode.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varnostne zahteve za vezana brusilna sredstvaSicherheitsanforderungen für Schleifkörper aus gebundenem SchleifmittelExigences de sécurité pour les produits abrasifs agglomérésSafety requirements for bonded abrasive products25.100.70BrusivaAbrasivesICS:Ta slovenski standard je istoveten z:EN 12413:2007+A1:2011SIST EN 12413:2007+A1:2011en,fr,de01-maj-2011SIST EN 12413:2007+A1:2011SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12413:2007+A1
March 2011 ICS 25.100.70 Supersedes EN 12413:2007English Version
Safety requirements for bonded abrasive products
Exigences de sécurité pour les produits abrasifs agglomérés
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel This European Standard was approved by CEN on 10 May 2007 and includes Amendment 1 approved by CEN on 17 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12413:2007+A1:2011: ESIST EN 12413:2007+A1:2011
Marking . 36A.1Content of marking . 36A.2Execution of marking . 39Annex B (informative)
Mounted points . 40B.1Example calculation of the maximum permissible speeds of rotation . 40B.2Example for application of the calculation method . 44Annex C (normative)
Verification methods for side load capacity . 46C.1General . 46C.2Single point side load . 46C.3Three point side load . 47C.4Impact test . 48Annex D (informative)
Colour codes . 49Annex E (informative)
Speed conversion table . 50Bibliography . 51 SIST EN 12413:2007+A1:2011
1 Scope This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products. This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer. The hazards taken into consideration are listed in Clause 4 of this standard. This standard does not apply to superabrasives and coated abrasive products. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 6103, Bonded abrasive products — Permissible unbalances of grinding wheels as delivered — Static testing (ISO 6103:2005) ISO 525, Bonded abrasive products — General requirements ISO 13942, Bonded abrasive products — Limit deviations and run-out tolerances 3 Definitions and symbols 3.1 Bonded abrasive products Products consisting of abrasives e.g. aluminium oxide, silicon carbide held together by a bond. Bonded abrasive products within the meaning of this standard are all products as defined, see for example by ISO 525. 3.2 Grinding machines 3.2.1 Stationary machines Machines that are fixed in position during operation, see for example EN 13218. Included are fixed swing-frame machines and mobile machines clamped firmly in position during use. 3.2.2 Mobile machines Machines that are not fixed in position during operation. They are manually guided (but not supported) by hand during use, e.g. floor grinding machines, flexibly suspended swing-frame grinding machines. 3.2.3 Hand-held machines Machines, including those with flexible drives that are held in the hand during the grinding process, see for example EN 792-7, EN 792-9, EN 60745-2-3 and EN ISO 19432. SIST EN 12413:2007+A1:2011
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.