EN ISO 8559-2:2020
(Main)Size designation of clothes - Part 2: Primary and secondary dimension indicators (ISO 8559-2:2017)
Size designation of clothes - Part 2: Primary and secondary dimension indicators (ISO 8559-2:2017)
ISO 8559-2:2017 specifies primary and secondary dimensions for specified types of garments to be used in combination with ISO 8559‑1 (anthropometric definitions for body measurement).
The primary aim of this document is to establish a size designation system that can be used by manufacturers and retailers to indicate to consumers (in a simple, direct and meaningful manner) the body dimensions of the person that the garment is intended to fit. Provided that the size of the person's body (as indicated by the specified dimensions) has been determined in accordance with ISO 8559‑1, this designation system will facilitate the choice of garments that fit. This information can be indicated by labelling, etc.
The size designation system is based on body measurements, not garment measurements. The choice of garment measurements is normally determined by the designer and the manufacturers who make appropriate allowances to accommodate the type and position of wear, style, cut and fashion elements of the garment.
Größenbezeichnung von Bekleidung - Teil 2: Primär - und Sekundärmaßkennzeichen (ISO 8559-2:2017)
Désignation des tailles de vêtements - Partie 2: Indicateurs des dimensions principales et secondaires (ISO 8559-2:2017)
L'ISO 8559-2:2017, à utiliser conjointement avec l'ISO 8559‑1 (définitions anthropométriques pour la mesure du corps), spécifie les mesures principales et secondaires pour des types spécifiés de vêtements.
Ce document a pour principal objet d'établir un système de désignation des tailles de vêtements pouvant être utilisé par les fabricants et les détaillants pour indiquer aux consommateurs, d'une manière simple, directe et explicite, les mensurations de la personne pour laquelle la taille du vêtement est adaptée. Grâce à une détermination précise des mensurations du corps humain (comme indiqué par les mesures spécifiées), conformément à l'ISO 8559‑1, ce système de désignation facilitera le choix d'un vêtement adapté. Ces informations peuvent être indiquées par un étiquetage, etc.
Le système de désignation des tailles est fondé sur les mesures corporelles et non pas sur celles des vêtements. Le choix des mesures des vêtements est d'ordinaire déterminé par le modéliste et les fabricants des vêtements, qui établiront les tolérances à prendre en compte selon le type, la position, le style, les éléments de coupe et de mode du vêtement.
Označevanje velikosti oblačil - 2. del: Kazalniki primarnih in sekundarnih mer (ISO 8559-2:2017)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2021
Označevanje velikosti oblačil - 2. del: Kazalniki primarnih in sekundarnih mer (ISO
8559-2:2017)
Size designation of clothes - Part 2: Primary and secondary dimension indicators (ISO
8559-2:2017)
Größenbezeichnung von Bekleidung - Teil 2: Primär - und Sekundärmaßkennzeichen
(ISO 8559-2:2017)
Désignation des tailles de vêtements - Partie 2: Indicateurs des dimensions principales
et secondaires (ISO 8559-2:2017)
Ta slovenski standard je istoveten z: EN ISO 8559-2:2020
ICS:
61.020 Oblačila Clothes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8559-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2020
EUROPÄISCHE NORM
ICS 61.020
English Version
Size designation of clothes - Part 2: Primary and secondary
dimension indicators (ISO 8559-2:2017)
Désignation des tailles de vêtements - Partie 2: Größenbezeichnung von Bekleidung - Teil 2: Primär -
Indicateurs des dimensions principales et secondaires und Sekundärmaßkennzeichen (ISO 8559-2:2017)
(ISO 8559-2:2017)
This European Standard was approved by CEN on 23 November 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8559-2:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 8559-2:2017 has been prepared by Technical Committee ISO/TC 133 "Clothing sizing
systems - size designation, size measurement methods and digital fittings” of the International
Organization for Standardization (ISO) and has been taken over as EN ISO 8559-2:2020 by Technical
Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2021, and conflicting national standards shall be
withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8559-2:2017 has been approved by CEN as EN ISO 8559-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 8559-2
First edition
2017-03
Size designation of clothes —
Part 2:
Primary and secondary dimension
indicators
Désignation des tailles de vêtements —
Partie 2: Indicateurs des dimensions principales et secondaires
Reference number
ISO 8559-2:2017(E)
©
ISO 2017
ISO 8559-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 8559-2:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Definition of primary and secondary dimensions in garments .2
5 Size designation . 5
5.1 General . 5
5.2 Garment dimensions . 6
5.3 Garment with cups . 6
6 Labelling . 6
6.1 Method . 6
6.2 Label attachment. 6
6.3 Additional information . 6
6.4 Examples of labels . 6
Annex A (informative) Examples of labels of size designation . 8
Bibliography .24
ISO 8559-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html
The committee responsible for this document is ISO/TC 133, Clothing sizing systems — Size designation,
size measurement methods and digital fittings.
This first edition cancels and replaces ISO 3636, ISO 3637, ISO 3638, ISO 4415, ISO 4416, ISO 4417 and
ISO 4418, which have been technically revised.
A list of all parts in ISO 8559 can be found on the ISO website.
iv © ISO 2017 – All rights reserved
ISO 8559-2:2017(E)
Introduction
Different sizing systems in different companies mean that different size designations can fit people
with identical or very similar body measurements.
This document can be used as a reference document for an international size designation system for
different types of garment.
INTERNATIONAL STANDARD ISO 8559-2:2017(E)
Size designation of clothes —
Part 2:
Primary and secondary dimension indicators
1 Scope
This document specifies primary and secondary dimensions for specified types of garments to be used
in combination with ISO 8559-1 (anthropometric definitions for body measurement).
The primary aim of this document is to establish a size designation system that can be used by
manufacturers and retailers to indicate to consumers (in a simple, direct and meaningful manner) the
body dimensions of the person that the garment is intended to fit. Provided that the size of the person’s
body (as indicated by the specified dimensions) has been determined in accordance with ISO 8559-1,
this designation system will facilitate the choice of garments that fit. This information can be indicated
by labelling, etc.
The size designation system is based on body measurements, not garment measurements. The choice
of garment measurements is normally determined by the designer and the manufacturers who make
appropriate allowances to accommodate the type and position of wear, style, cut and fashion elements
of the garment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8559-1, Size designation of clothes — Anthropometric definitions for body measurement
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
primary dimension
body dimension, in centimetres, that is used to designate the size of a garment for the consumer
3.2
secondary dimension
body dimension, in centimetres (or in the case of pantyhose, body mass in kilograms), that can
additionally be used to designate the size of a garment for the consumer
3.3
cup size
difference between the bust girth and the underbust girth
Note 1 to entry: See ISO 8559-1:2017, 5.7.7.
---------------------- P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.