prEN ISO 15613
(Main)Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO/DIS 15613:2022)
Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO/DIS 15613:2022)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Qualifizierung aufgrund einer vorgezogenen Arbeitsprüfung (ISO/DIS 15613:2022)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Qualification sur la base d'un assemblage soudé de préproduction (ISO/DIS 15613:2022)
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Kvalifikacija na podlagi predproizvodnega preskusa varjenja (ISO/DIS 15613:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2022
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Kvalifikacija na
podlagi predproizvodnega preskusa varjenja (ISO/DIS 15613:2022)
Specification and qualification of welding procedures for metallic materials - Qualification
based on pre-production welding test (ISO/DIS 15613:2022)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Qualifizierung aufgrund einer vorgezogenen Arbeitsprüfung (ISO/DIS 15613:2022)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Qualification sur la base d'un assemblage soudé de préproduction
(ISO/DIS 15613:2022)
Ta slovenski standard je istoveten z: prEN ISO 15613
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15613
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-08-02 2022-10-25
Specification and qualification of welding procedures
for metallic materials — Qualification based on a pre-
production welding test
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques —
Qualification sur la base d'un assemblage soudé de préproduction
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15613:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
ISO/DIS 15613:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15613
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
Specification and qualification of welding procedures
for metallic materials — Qualification based on a pre-
production welding test
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques —
Qualification sur la base d'un assemblage soudé de préproduction
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 15613:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
ISO/DIS 15613:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Preliminary welding procedure specification (pWPS) . 1
5 Qualification of the welding procedure . 2
6 Welding of test pieces .2
7 Testing. 2
7.1 Fusion welding . 2
7.2 Resistance welding . 2
7.2.1 General . 2
7.2.2 Overlap welding . 2
7.2.3 Butt welding . 3
8 Range of qualification . 3
9 Validity . 3
10 Welding procedure qualification record (WPQR). 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU (PED) aimed to be covered .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/29/EU (SPVD) aimed to be covered .5
iii
ISO/DIS 15613:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Quality management in the field of welding.
Any feedback, question or request for official interpretation related to any aspect of this document
should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete
listing of these bodies can be found at www.iso.org/members.html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
This second edition cancels and replaces the first edition (ISO 15613:2004), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— normative references have been updated;
— further changes to be identified after DIS ballot.
iv
ISO/DIS 15613:2022(E)
Introduction
One of the methods for welding procedure qualification is based on a pre-production welding test as
given in ISO 15607.
Qualification based on a pre-production welding test can be used where the shape and dimensions of
the standard test pieces do not adequately represent the joint to be welded.
In such cases, one or more special test pieces can be made to simulate the production joint in all
essential features, e.g. dimensions, restraint, heat sink effects, limited access. In the case of resistance
welding, actual components have to be used for the pre-production test.
v
DRAFT INTERNATIONAL STANDARD ISO/DIS 15613:2022(E)
Specification and qualification of welding procedures
for metallic materials — Qualification based on a pre-
production welding test
1 Scope
This document specifies how a preliminary welding procedure specification is qualified based on pre-
production welding tests.
This document is applicable to arc welding, gas welding, beam welding, resistance welding, stud
welding and friction welding of metallic materials. The principles of this document may be applied to
other welding processes.
This document is a part of a series of standards dealing with specification and qualification of welding
procedures. Details are given in ISO 15607.
The use of this document can be restricted by an application standard or specification.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 10447, Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection
welds
ISO 15607, Specification and qualification of welding procedures for metallic materials — General rules
ISO/TR 15608, Welding — Guidelines for a metallic materials grouping system
ISO 15609 (all parts), Specification and qualification of welding procedures for metallic materials —
Welding procedure specification
ISO 15614 (all parts), Specification and qualification of welding procedures for metallic materials —
Welding procedure test
ISO/TR 25901 (all parts), Welding and allied processes — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in the ISO/TR 25901 (all parts) and
ISO 15607 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Preliminary welding procedure specification (pWPS)
A preliminary welding procedure specification shall be prepared in accordance with the relevant part
of ISO 15609.
ISO/DIS 15613:2022(E)
5 Qualification of the welding procedure
Qualification of the welding procedure shall be carried out by an examiner or examining body in
accordance with the relevant part of ISO 15614 as modified by this document.
6 Welding of test pieces
Preparation and welding of the test pieces shall be carried out under the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.